Advertisement
Quick Links
Applies to all available screen materials:
Product Description: The Aeon Series is a fixed frame projection
The EDGE FREE
design resembles a giant size flat
ign resembles a giant size flat panel TV display. The Aeon includes a
®
installation option to further enhance the frame appearance and
installation option to further enhance the frame appearance and absorb projector overshoot
backlighting kit is available for added visual appearance
Hardware and Parts List
Please make sure all parts listed below are included
A. Elbow joint x 4 pcs
E. Center Support bar x 1-2
pc
I. M6x12 screw x 2-12pcs
M. Black Tape x 1 bag
Rev.070216-MZ
Aeon Series
EDGE FREE® Fixed Frame Projection Screen
EDGE FREE
Fixed Frame Projection Screen
User's Guide
CineGrey 3D EDGE FREE
Series is a fixed frame projection screen that uses Elite's EDGE FREE
for added visual appearance.
re included before installation.
B. Top/Bottom horizontal
B. Top/Bottom horizontal
fame x 4 pcs
fame x 4 pcs
F. Wall brackets x 2-3 pcs
F. Wall brackets x
J. M5x50 screws and anchor x
. M5x50 screws and anchor x
6 pcs
N. Bezel trim
ezel trim x 6 pcs
www.elitescreens.com
and CineWhite
CineWhite™ EDGE FREE
®
uses Elite's EDGE FREE™ technology.
n includes an ultra-thin trim as an
absorb projector overshoot. An optional LED
C. Left/Right vertical
frame x 2 pcs
G. M6 screw x 2-12 pcs
K. Rubber hammer x 1 pc
O. Corner Support Bar
(180"-200") x 4 pcs
®
D. Center joints x 2 pcs
H. M5x15 screw x 24 pcs
H. M5x15 screw x
L. Screwdriver x 1 pc
O. Corner sleeve x 4 pcs
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Elite Screens EDGE FREE Aeon Series
Summary of Contents for Elite Screens EDGE FREE Aeon Series
- Page 1 Aeon Series EDGE FREE EDGE FREE® Fixed Frame Projection Screen Fixed Frame Projection Screen User’s Guide Applies to all available screen materials: CineGrey 3D EDGE FREE and CineWhite CineWhite™ EDGE FREE ® ® Product Description: The Aeon Series is a fixed frame projection Series is a fixed frame projection screen that uses Elite’s EDGE FREE uses Elite’s EDGE FREE™...
- Page 2 Frame Assembly 1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H). 2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws. 3.
- Page 3 6. Insert the two vertical short frames(C) into the elbow joint (A). Horizontal long frame (B) push push Vertical short frame (C) Note: For models 180” and above, ensure two M6 screws (G) are inserted on each vertical frame before proceeding to step 7. Face up 7.
-
Page 4: Screen Material Installation
8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the M5x15 Screws (H). Four corners join correctly to form a perfect square. Use the included screwdriver (L) to fasten the Mx15 screws (H) into each corner by aligning the frame screw holes to the holes in the elbow joint (A). - Page 5 3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following order A→B→C→D (see instructions below for details). Attach the screen material to the corners as shown below. 3) Fold over second side 4) Repeat until all four 1) Stretch the screen 2) Fold over and attach...
- Page 6 5. Proceed to attach the rest of the material to the frame as described in the illustrations below. Proceed to attach the rest of the material to the frame as described in the illustrations below. Proceed to attach the rest of the material to the frame as described in the illustrations below. Grasp the middle of the of the screen material and attach it to the velcro...
- Page 7 6. If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material. Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure prolonging the life of the screen material.
- Page 8 Support bar installation (for models (for models 180” and above): 1. Position the center support bar (E) center support bar (E) and M6 hex screws (G) in the areas of the frame shown in fig 1. Align the in the areas of the frame shown in fig 1. Align the hole on each end of the support bar with the hole on each end of the support bar with the M6 hex screws (G) located at the top and bottom frame ted at the top and bottom frame sections.
- Page 9 Notice to Installer: Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D Angular Reflective ALR (Ambient Light Rejecting) Screen. Make sure to follow these instructions in order for the CineGrey 3D to perform correctly. •Angular-Reflective material is not compatible with ultra/short-throw projectors •Minimum lens throw ratio 1.5x image width •Ambient light must not come from the same direction as the projector...
- Page 10 Figure 2 NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The back of the material should be labeled with a DOWN sticker to indicate the material is facing in the down position. The Elite Screens logo should be installed on the DOWN side 3.
- Page 11 4. After the bezel trim has been installed en installed, place a corner sleeve (O) on all four corners. four corners. Begin by aligning and adjusting the corner sleeve through the front of the screen through the front of the screen. Make sure the corner sleeve comple completely wraps the edge of the bezel trim.
-
Page 12: Installation
4. The design of the wall brackets allows the frame to slide over them through its sides. This is an important feature of the installation design as it allows your screen to be properly centered. For a local Elite Screens contact or Technical Support, please visit www.elitescreens.com Rev.070216-MZ...
Need help?
Do you have a question about the EDGE FREE Aeon Series and is the answer not in the manual?
Questions and answers