Integration Points List - Water-To-Air Standard Software - Bosch FHP560 Applications Manual

2 8 | FHP560 Controller

13 Integration Points List - Water-to-Air Standard Software 7.05.03

Integration Points
BACnet MODBUS
Point Description
#
Name
Type Object
Name
Type
ID
1 BAS CO₂ Sensor Value bas_CO₂_val_1 AV:49 fl oat value
2 BAS Mixed Air Temp bas_mat_1 AV:86 fl oat value
BAS Outside Air
3 effective_oat_1 AV:29 fl oat value
Temperature
4 BAS RH Sensor Value bas_rh_sen_val_1 AV:56 fl oat value
BAS Temperature
5 bas_sen_val_1 AV:19 fl oat value
Sensor Value
Evaporator Coil
6 coil_cfg_1 AV:94 fl oat value
Confi guration Selection
Compressor Control
7 comp_mode_1 AV:64 fl oat value
Mode
8 Compressor Stages cmp_stgs_1 AV:14 fl oat value
Compressor Stages
9 stages_1 AV:114 fl oat value
Selection
10 Control Source ctrl_source_1 AV:15 fl oat value
Cooling Demand
11 clg_pct_1 AV:13 fl oat value
Percentage
12 IN-2 Mode Status ui2_mode_status_1 AV:18 fl oat value
Table 23
Data subject to change
N2 LON
Read
Only
SNVT
Register Type ID Name SNVT
#
40001 data fl oat 1 1 nviBasCO₂Val SNVT_ppm(29)
40003 data fl oat 2 ‒ ‒ ‒
SNVT_
40005 data fl oat 3 0 nviEffectiveOAT
temp_p(105)
SNVT_lev_
40007 data fl oat 4 15 nviBasRhSenVal
percent(81)
SNVT_
40009 data fl oat 5 2 nviBasSenVal
temp_p(105)
40011 data fl oat 6 ‒ ‒ ‒
40013 data fl oat 8 ‒ ‒ ‒
SNVT_count_
40001 data fl oat 7 16 nvoCmpStgs

inc(9)
40107 data fl oat 79 ‒ ‒ ‒
SNVT_count_
40023 data fl oat 12 3 nviCtrlSource
inc(9)
40025 data fl oat 13 ‒ ‒ ‒

40033 data fl oat 55 ‒ ‒ ‒

Integration Points
Point Description
#
Name
Description
BAS CO₂ Sensor Value in PPM
Default: 1001 PPM
BAS Mixed Air Temperature Value
Current Alarm
in °F
13
Condition Status
Default: 66.5 °F
Effective Outside Air Temperature
in °F
Default: 60 °F
RH Sensor Value Supplied by BAS
in %
Default: 56 %RH
BAS Zone Temperature Sensor
Value in °F
Damper Occupancy
Default: 74 °F
14
Selection
Coil Confi guration Setup
0 = Parallel (Default)
1 = Series
Compressor Mode Setup
0 = Zone Control - ZS (Default)
1 = Discharge Air Control
2 = Zone Control - BAS Sensor
3 = Zone Control - Remote Sensor
Reports Confi guration Status of
DI5 Mode (Digital
Compressor Stages 15
Input 5)
1 = 1 Compressor 1 Stage
2 = 2 Compressor 2 Stages
5 = 1 Compressor 2 Stages
Selected Compressor Stages
(Confi gured at Factory)
1 = 1 Compressor 1 Stage
2 = 2 Compressor 2 Stages
5 = 1 Compressor 2 Stages
(Default) Discharged Air
16
Temperature Setpoint
Control Source for Occupancy
Setup
Effective Cooling
17
0 = Digital Input Enable (e.g. Room
Setpoint
Occupancy Sensor)
1 = Keypad Schedule
18 Effect Disch Air Temp
2 = BAS Occupancy Command
(Default)
3 = Factory Use Only
Entering Water
19
4 = Manual On-Continuous
Temperature
Cooling Status in Demand Percent, Effective Heating
20
% Setpoint
Modulating Damper
Reports how the controller Input 21 eff_dpr_pos_screen_1
Position
#2 (IN-2) is confi gured
0 = Not Used
1 = Zone Remote Sensor 22 Zone Humidity eff_zone_humid_1
2 = Outdoor Air Temperature
Sensor
Leaving Water
3 = Entering Water Temperature 23
Temperature (LWT)
Sensor
4 = Mixed Air Temperature Sensor
Mixed Air Temperature
5 = Relative Humidity Sensor 24
(MAT)
(Probe)
6 = Digital Enable (e.g. Room
Outdoor Air
Occupancy Sensor) 25
Temperature (OAT)
7 = Return Air Temperature Sensor
Table 24
Page____ of ____
BACnet MODBUS N2
Type SNVT
Object
Name Register Type ID
ID Type #
current_alarm_1 AV:17 fl oat value 40003 data fl oat 9 17
mdpr_occ_sel_1 AV:97 fl oat value 40031 data fl oat 16 ‒
di5_mode_1 AV:60 fl oat value 40015 data fl oat 10 ‒
dat_stpt_1 AV:30 fl oat value 40017 data fl oat 11 18
eff_clg_stpt_1 AV:5 fl oat value 40039 data fl oat 20 4
eff_dat_1 AV:10 fl oat value 40011 data fl oat 18 21
eff_ewt_1 AV:62 fl oat value 40013 data fl oat 19 22
eff_htg_stpt_1 AV:6 fl oat value 40045 data fl oat 23 5
AV:81 fl oat value 40047 data fl oat 24 ‒
AV:20 fl oat value 40021 data fl oat 26 24
eff_lwt_1 AV:11 fl oat value 40015 data fl oat 21 23
eff_mat_1 AV:87 fl oat value 40017 data fl oat 22 ‒
eff_oat_1 AV:75 fl oat value 40055 data fl oat 28 6
Applications Manual
LON
Read
Description
Only
Name SNVT
Alarm Status of unit:
0 = No Alarm,
1-10 = UPM Fault Code
20 = Output Overridden via Keypad
30 = Sensor Failure
40 = Leaving Water Temp Alarm
50 = Zone Temp Alarm
SNVT_count_
nvoCurrentAlarm  60 = Discharge Air Temperature
inc(9)
Alarm
70 = Filter Alarm/Compressors 1 &
2 Runtime
80 = Zone Humidity Alarm
90 = High CO₂ Level Alarm
100 = Differential Pressure Switch
(DPS) Alarm"
Damper Occupancy Selection
Setup
0 = Disabled
‒ ‒
1 = Occupied (Default)
2 = Unoccupied
3 = Any Occupancy
Controller Input #5 Confi guration
Selection
0 = Dirty Filter Switch
1 = Entering Water Temp Sensor -
Economizer/Boilerless
2 = Differential Pressure Switch
3 = Secondary Condensate Pan
4 = Fan Status Switch
‒ ‒
5 = Valve End Switch
6 = Damper End Switch
7 = Smoke Detector Switch
8 = Pump Status Switch
9 = MIxed Air Temp Sensor - Mixed
Air Control
10 = Input Expansion Module (IEM)
11 = Not Used (Default)
Discharged Air Temperature
SNVT_
nviDatStpt Setpoint Setup in °F
temp_p(105)
Default: 65 °F
SNVT_ Effective Cooling Setpoint (after
nvoEffClgStpt 
temp_p(105) setpoint adjustment applied) in °F
SNVT_ Discharge Air Temperature (DAT)
nvoEffDat 
temp_p(105) in °F
SNVT_ Water Side Economizer Effective
nvoEffEwt 
temp_p(105) Entering Water Temperature in °F
SNVT_ Effective Heating Setpoint (after
nvoEffHtgStpt 
temp_p(105) setpoint adjustment applied) in °F
Effective Outside Air Damper
‒ ‒

Position in %
SNVT_lev_ Effective Zone Humidity in Percent
nvoEffZoneHumid

percent(81) RH (%)
SNVT_ Effective Leaving Water
nvoEffLwt

temp_p(105) Temperature Status in °F
Effective Mixed Air Temperature
‒ ‒

in °F
SNVT_ Effective Outdoor Temperature
nvoEffOat

temp_p(105) Status in °F
Bosch Thermotechnology Corp.