Panasonic SP22P Maintenance Manual page 120

MEASURES FOR
ERROR
Symbols
(+) overrun ....................................................... 4-7
(-) overrun ........................................................ 4-7
(-5001) The parameter is incorrect ................... 4-2
(-5002) Hardware error .................................... 4-2
(-5004) Object-limit over ................................... 4-2
(-5005) Insufficient memory ............................. 4-2
(-5009) Double defined directory ..................... 4-2
(-5010) File not found ....................................... 4-2
A
Air pressure drop ..................................... 4-3, 4-5
Air pressure drops .......................................... 4-10
Axis controller communication error ................. 4-7
Axis error of emergency stop ........................... 4-7
C
C→R conveyor transport error ......................... 4-6
Center conveyor transport error ....................... 4-6
Center conveyor width adjustment timeout ...... 4-5
Cleaning nozzle down error ............................. 4-5
Cleaning nozzle up error .................................. 4-5
Cleaning paper empty ...................................... 4-4
Cleaning solvent empty stop ............................ 4-4
Cleaning unit couple error ................................ 4-6
Cleaning unit fixed error ................................... 4-6
Cleaning unit position error .............................. 4-6
Cleaning unit set NG ........................................ 4-6
Communication error with recognition device .. 4-2
Could not be deleted the recognition data ....... 4-2
Could not be read the recognition data ............ 4-2
Could not be saved the recognition data ......... 4-2
Counter error .................................................... 4-7
Cover open ............................................ 4-3, 4-11
Cover open stop ............................................... 4-5
D
Data check ....................................................... 4-3
Data delete error .............................................. 4-2
Data error ......................................................... 4-7
Data load error ................................................. 4-2
Data save error ................................................ 4-2
DC down .......................................................... 4-6
Device list ....................................................... 4-26
Directory load error .......................................... 4-2
Disk initialization error ...................................... 4-2
Disk is write protect .......................................... 4-8
Disk is write protected ...................................... 4-2
Disk not inserted .............................................. 4-2
Driver condition ................................................ 4-3
Driver error ............................................. 4-7, 4-16
Page 2
E
Emergency stop error ...................................... 4-5
Emergency switch .................................... 4-3, 4-9
Emergency switch ON ...................................... 4-5
Emergency switch on ....................................... 4-9
Errors in using the floppy disk .......................... 4-2
Error messages (error list) ............................... 4-2
Errors during PT network ................................. 4-2
Errors during the self-diagnosis ....................... 4-3
F
F conv. board transport error ............................ 4-4
F squeegee down error .................................... 4-6
F squeegee up timeout .................................... 4-5
F→R conveyor transport error ......................... 4-6
Feedback error ....................................... 4-7, 4-15
Format error ............................................. 4-2, 4-8
I
Immediate stop error ........................................ 4-4
Input check after error .................................... 4-27
L
Left conveyor width adjustment timeout ........... 4-5
Lift axis brake off ....................................4-3, 4-13
Lifter shaft brake off ......................................... 4-6
Limit switch list (LS) ....................................... 4-23
Load list .......................................................... 4-22
Lord arrangement .......................................... 4-19
M
Motor list (M) .................................................. 4-24
O
Output check after error ................................. 4-28
P
Paste recognition error ..................................... 4-6
PCB extend error ............................................. 4-4
PCB holder origin error .................................... 4-5
PCB positioning error ....................................... 4-5
PCB recognition error ...................................... 4-4
PCB stopper return error .................................. 4-6
PCB transport error ................................ 4-5, 4-14
PCB vacuum error ............................................ 4-6
Photo sensor list 1 (PH) ................................. 4-22
Positioning time over error ............................... 4-7
Power box fan motor ...................................... 4-12
Power motor fan box ........................................ 4-3
Pre process production end ................... 4-3, 4-10
Pressure data error .......................................... 4-6
Pressure teach ................................................. 4-3
Printable area over ........................................... 4-5
PT communication error ................................... 4-2
PT communication time-out ............................. 4-2
PT recog data not exist .................................... 4-2
193C-E-MMA0Z-A01-01