Advertisement
Overview - Baby unit
Sound sensitivity and sound activation
Sound sensitivity
With sound sensitivity setting, you can choose to hear sounds from the
Microphone
baby unit all the time, or to hear sounds that exceed a certain level. The
default level Highest allows you to hear all sounds (including background
Infrared LEDs
noises).
Camera
Light sensor
If you set the sound sensitivity to
a lower level (e.g. Medium), you
ON/OFF
will only hear sounds that exceed
LED light
the selected level. The baby unit
may not detect soft sounds, and
the parent unit speaker may remain
quiet.
For details, please see Adjust the
sound sensitivity of the baby unit
in the User's manual.
Speaker
Night vision
Power jack
ON/OFF switch
Temperature
sensor
Wall mount holes for
upright mounting
Wall mount holes for
lateral mounting
Sound activation
When sound activation is on, the parent unit screen stays off
VOX Sensitivity
Low
to save power when the baby unit detects no sound.
Medium
Once the baby unit detects sounds that are louder than the
High
chosen sound sensitivity level, the parent unit screen turns
Highest
on automatically. It will then turn off again after 50 seconds
of no sound detection.
Dim mode
The baby unit has infrared LEDs that
With dim mode preset to
allow you to see your baby clearly at
LCD
LCD
on, your parent unit display
night or in a dark room. When the baby
Brightness
Brightness
will dim to conserve energy
unit being viewed detects low light
Dim Mode
Dim Mode
after 10 minutes of inactivity,
levels, the infrared LEDs are switched
in which there is neither key
on automatically. The images from the
pressed nor alert received
baby unit are in black and white, and
from the baby unit.
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
10 min inactivity
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
Press any buttons
colors and backgrounds, the video quality
may vary. Adjust the baby unit's angle or
NOTES
NOTE
Note
place the baby unit at a higher level to
• If you do not want LCD to dim automatically, turn off the Dim Mode.
prevent glare and blurry display.
Mount the baby unit on dry wall (optional)
Items to purchase
Sound-activated Screen
On
You will need to purchase the
O
following items separately to
mount your baby unit:
2 screws
2 anchors
Drill two holes in the wall.
Note
NOTE
NOTES
If you drill the holes into a stud, go to
• The types of screws and anchors you
step 3.
need depend on the composition of the
-OR-
wall.
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Dim Mode
Dim Mode
On
On
Note
NOTES
NOTE
Insert the screws into the holes and tight-
en the screws until only 1/4 inch of the
• Check for reception strength and camera
screws are exposed.
angle before drilling the holes.
Use a pencil to mark two holes in
parallel. Make sure they are the same
distance apart as the wall mount holes
on the baby unit.
For VM5251-2 only
Status check - Two baby units
Change different views - Single CAM
If you are viewing baby unit
, the POWER
In Single CAM or Patrol mode, press VIEW to switch
LED light of baby unit
turns on. As baby
between the image of baby units
is not being viewed, its POWER LED
unit
light flashes.
OR
Change different views - Patrol
Depending on your preference, choose
the upright or lateral orientation to mount
your unit. Align the wall mount holes at the
Select Patrol as your monitoring mode to alternately
bottom or at the rear side of the baby unit
view the image from baby units
with the screws on the wall. Slide the baby
seconds.
unit down until it locks into place.
NOTES
Note
NOTE
• If you power on only one baby unit, you may see
the parent unit displaying
and then
No link to CAM # (# represents the baby unit
number), and the LINK LED light flashing.
Press VIEW in Single CAM or Patrol mode to switch
Change different views - Split
OR
to the baby unit you have powered on.
Select Split as your monitoring mode to view the
images from both baby units at once.
Tilt or rotate to adjust camera angle.
Monitoring Mode
Single CAM
Patrol
Split
and
.
Press VIEW
Monitoring Mode
Single CAM
Patrol
and
every 10
Split
10s
Monitoring Mode
Single CAM
Patrol
Split
Advertisement
