Table of Contents
Advertisement
8.5.4.
8.5.4.
8.5.4.
8.5.4. Withdraw the element assembly from tank body/sensor assembly.
8.5.4.
8.5.5.
8.5.5.
8.5.5.
8.5.5.
8.5.5. Renew element assembly. Make sure that the location spigot on the tank
body/sensor assembly engages in the cutout in the element assembly.
8.5.6.
8.5.6.
8.5.6.
8.5.6. Refit in reverse order. To prevent overheating, make sure that the wiring
8.5.6.
is correctly routed, and that all the screws are tight and are not cross-
threaded. Make sure that the thermal switch clip is fitted correctly.
8.6. To clean the element assembly:
8.6.
8.6.
8.6.
8.6.
8.6.1.
8.6.1.
8.6.1. Refer
8.6.1.
8.6.1.
assembly"
assembly" and remove the element assembly.
assembly"
assembly"
assembly"
8.6.2.
8.6.2.
8.6.2.
8.6.2.
8.6.2. Unclip the thermal switch clip and remove the element retaining ring and
the seal.
8.6.3.
8.6.3. Immerse the element assembly up to the flange in a proprietary plastic
8.6.3.
8.6.3.
8.6.3.
kettle descalent. Follow the descalent manufacturer's instructions.
DO NOT allow the solution to come into contact with the element
DO NOT allow the solution to come into contact with the element
DO NOT allow the solution to come into contact with the element
DO NOT allow the solution to come into contact with the element
DO NOT allow the solution to come into contact with the element
assembly terminals or the plastic components.
assembly terminals or the plastic components.
assembly terminals or the plastic components.
assembly terminals or the plastic components.
assembly terminals or the plastic components.
Note!
Note! Heater elements may be damaged by excessive use of descalent
Note!
Note!
Note!
solution.
8.6.4.
8.6.4.
8.6.4.
8.6.4.
8.6.4. Refer to Section 8, Maintenance: "8.4. To renew the tank body/
sensor assembly"
sensor assembly"
sensor assembly" and remove the tank body/sensor assembly.
sensor assembly"
sensor assembly"
8.6.5.
8.6.5.
8.6.5.
8.6.5. Rinse out the tank body/sensor assembly in cold water to remove any
8.6.5.
limescale.
DO NOT immerse tank body/sensor assembly in descalent.
DO NOT immerse tank body/sensor assembly in descalent.
DO NOT immerse tank body/sensor assembly in descalent.
DO NOT immerse tank body/sensor assembly in descalent.
DO NOT immerse tank body/sensor assembly in descalent.
8.6.6.
8.6.6.
8.6.6.
8.6.6.
8.6.6. Refit in reverse order. Make sure that the thermal switch clip is fitted
correctly.
to Section 8, Maintenance: "8.5. To renew the element
Section 8, Maintenance: "8.5. To renew the element
Section 8, Maintenance: "8.5. To renew the element
Section 8, Maintenance: "8.5. To renew the element
Section 8, Maintenance: "8.5. To renew the element
Section 8, Maintenance: "8.4. To renew the tank body/
Section 8, Maintenance: "8.4. To renew the tank body/
Section 8, Maintenance: "8.4. To renew the tank body/
Section 8, Maintenance: "8.4. To renew the tank body/
41
41
41
41
41
- Quick Links:
- Fault Diagnosis Fault Diagnosis
Hide quick links:
Advertisement
Table of Contents
