Advertisement
11. Arm the ayahm from a eoneole or koyw
anci hrnediatety
Wow the arming sequence of security code entry plus an-
ing command (AWAY or STAY) by daproaalon of the
INSTANT Lay. The lNSTANT LED on the console should
light. After allowing for the exit delay to expire. any fault intro-
duced in the entry/exit zone will cause an immediate alarm.
Disarm the system and nnte that the INSTANT LED will QO out.
12
turn on tlw Chlma Mode by entering the security code fol-
lowed by depression of the CHIME key during the disarmed
state. Open and close any contact in a zone selected for
chime enable and a single tone will be produced at any con-
sole or keypad for each fauft. announcing the entry of some-
one. Remove the Chime Mode by reentering the security code
followed by depression of the CHIME key.
13. Conduel a bur~faty
toat
by entering the security code fol-
lowed by depression of the TEST key. This will initiate a test of
the sensing circuitry by shorbng all zones. The alarm sounder
will sound trqm battery power lor 3 seconds and 8 will be dis-
played at the console if all the sensing circuitry is operating
and
as a test of
all
of the liihtable segments of
the display.
15 seconds later, the system will automatically enter the instal-
lation test mode provided the user did not disarm the system.
.
When in the instalfation test mode, the console will beep every
15 seconds to remind the user that the system is not active. A
test report 10 the central station is initiated when entering this
mode. Activation of any zone causes a bnaf 'k second sound-
ing from the exterior alam sounder(s), as wall as visual zone
annunciation on the console's zone idantffication display.
14. All the tone oonlKtr
may now be chuked
W dlsturblnQ
each contact m each zone and listening tOr the short SIren
and/or bell sound (whichever is used). The inSlattatiOn test
mode will not tlmeout. II must be ended manually by keying
the security code lottowed by depression of fhe OFF
key.
15. Dbconnacl
AC power to the
l yabrn.
The POWER LED on
the console should go oul within 5 seconds. but the system
should remain operable. After an installer PROM programmed
AC Loss delay (up to 36 minutes), a rapidly pulsing trouble
sound will be produced at consoles and keypads and an AC
Loss report will be communicated to the central station. KeymQ
of the security code and OFF is required to silence the trouble
sounding.
NOTE: The AC Loss sounding is suppressed while the system
is armed. The sound is only produced when the OFF
LED (on the console) IS lit.
Restore AC power to the system.
16. Arm the rystam and rlmubta having the pnmbes
by fol-
lowing the procedures in the OPERATION Section.
17. Slmubte entry of (he prembes and dbarm the system
by
following the procedure gtven In the OPERATION
Section
AC POWER LED ON BACH SECURITY CONSOLE SHOULD BE LIT
AT AU TlYES. If out. AC lailure is indicated and the system is operating
on battery. Check plug-in transformer or for power failure.
TO ARM BURGLARY SYSTBM PROM CONSOLB/REMOTB
KEYPADS:
1. Make sun the AC POWER LED b St.
2 The READY LED on the con&e qr remote keypad ahoufd ba II1 to
indicate that no zones are faulted.
I1 tha READY LED b not IIt, check the Zone I.D. Display on the con-
sole (depress READYX&y to get display). A fautted zone indication
denotes a fault whtch must ba cleared or the zone bypassed (prior to
arming by individual zone bypass or during arming by the spatial auto-
matic bypassing forcad arming sequence. in order to arm the system).
Make sure that the exit dti
is closed!
2 En@ lho m.cwlIy code al the consob or remote keyPad.
a If rmmalnlng on Iha prwnbas
l
Ror arming, immadtatefy (within 2
seconds of code entry) press fhe STAY key. Interior zone(s) should
now be turned Off and the rest of the burglary zones in Me aysfam
should now be annad (entry/exit zones after exit delay timeout). This
is indicated at consoles and keypads by 3 brief tones and tha lighting
of the STAY LED.
b. If laavlng lha p#ambaa w
l
nnlng, immadiitafy (wifhin 2 seconds
of code entry) press the AWAY key. All bursfary zones should now be
armad (entry/exit zones after exit delay timeout). Thii is indicated at
consoles and keypads by 2 brief tones and the lighting of the AWAY
LED. Depart before the exit delay period ends. via an entry/exit door.
NOTE: Failure to arm is indicatad by a single lone at consoles and kay-
pads and by failure to turn off ma OFF LED (at consoles) and
turn on either the AWAY or STAY LED.
TO ARM BURGLARY BYBYBY FBOM TOUCHTONE*
PHONE:
NOtE: This feature can only ba used on systems equipped with a
No. 4178 Remote Phone Arming Module.
1. obl the l yamm"r tatopbona numbor.
2. Tha ayatam wflf pIckup afhr 10 rlnp and will sand a brief
aoknowladQmanl (V'm listening") tone.
2whonunackn~
ttw*nd8,llbouswwlllhave10
aaa~&
& &umu,
&g
tom. The arming tone is TouchTone@ digit
"2" artcj this digit musf be pressed for at least 025 seconds (to be cer-
fain, counf~ one one-thousand. fwo one-thousand).
4. If ti
aystam data&
the arming tona, it will then maxe an attempt to
force arm itself. After a briif pause it will respond wlrh enher one or Iwo
tX=OPS.
a A ringk beep lndluta
that the lysbm cannot k armed
because one or more zones not enabled tor DypaSS are tautted
b. Two boaps Indloate Hut lhe
l
ttrmpt to arm was wcautul.
A
closing report will be sent to the central momtonng stabon User l.D I
"P' will appear in Adamw high speed and expanoea low speed tor-
mat closing reports.
It ow or mom tones wublod for bypass wa fmdbd at arm Ume,
then these are automatically bypassed. A bypass report WIII be sent
to the central station in addiiion to the closing repon
NOTE: Two beeps can also indicate that the system IS alraaoy armed at
the lima that the current attempt to arm is maoe MO MW ctoslng
reporl is sent tf this is me case.
5. If the system. has not received Ihe arming tone
l
Ror Iho 10
aacond
ualting parI@ has alapaad, because of a faulty telco connecuon for
example, then it will simply hang up. The ann/dlsarm state 01 me system
will not be affected. The user should wait a few seconds oetore trytng
again.
TO DISARM BURGLARY SYSTBY:
1. When onterkq ttm pnmboa, enter only vb an enhy/oxH door. A
slowly pulsing tone will be heard from consoles
and
keypaos ounng the
entry delay period.
NOlEz If a rapidly pulsing tone is heard. it is an lndlcatlon or me
memory of an alarm that took place prewously The user Should
immediitely leave the premises and call the police trom a safe
tocation.
It already wlthln pnmbos,
go directly to the nearest console or
keypad.
2 Bofom the entry &by
period ilf any) ends, enter (he security code
and pmr
OtV.
NOm
While the system is disarmed, the READY LED will QO on and off
as the protected zones open and close dunng normal operation
of doors. windows. PIRs. etc . . . .
23
Advertisement
