Advertisement
4. TROUBLE ON SHORT ENABLE (Zones 5-k)
If none of the below is desired. DO NOT program anything. You are now
finished programming the Control PROM.
Trouble On Short Enabte can be programmed in any of the following
combinations (for Zones 1-4, see Item 4. PROM Data Group 16 on page
14).
ZONE 5
PROGRAM A 1
ZONE 6
PROGRAM A 2
ZONE 7
PROGRAM A 4
ZONE 6
PROGRAM AN 6
ZONES 5 AND 6
PROGRAM A 3
ZONES 5 AND 7
PROGRAM A 5
ZONES 5 AND 6
PROGRAM A 9
ZONES 5. 6 AND 7
PROGRAM A 7
ZONES 6 AND 7
PROGRAM A 6
For a combination not given above. follow the two pass procedure of Item
12 of PROM Data Group 2 on page 12.
FIRST PASS:
cl
SECOND PASS:
cl
8. COMMUNICATION
PROM
CommunlaUon
PROM Date Group 1
To program, set Phone No. Selector Switch lo "Primary" and Rotary Switch
to Position 1 (Access U) on No. 690 PROM Programmer
Prbaary PABX Acoeas Number' (Select from 0 lhru 9. Up lo 4 digits):
q IKIULI
(e.g..
9)
NOTE: This field should be programmed with a '70 (if TouchToneQ dialing
is used) or 1170 (if rotary [p&e] dialing is used) in installations
where a call wailing service is present on the phone line used. This
code can prevent call wailing from interrupting the outbound
communication on such lines, if the service inhibit option is present.
Communlceilon
PROM Data Group 2
To program, set Phone No. Selector Switch lo "Secondary" and Rotary
Switch lo Position 1 (Access #) on No. 690 PROM Programmer.
Bocondaty PABX Acoaes Number' (Sefect from 0 thru 9. up lo 4 digits):
Dun0
NOTE: (See note under Primary PABX Access Number)
Communkatlon
PROM Data Group 3
To program, set Phone No. Selector Switch to "Primary" and Rotary Switch
lo Position 2 (Main Phone No.) on No. 690 PROM Programmer.
Prlmaty Tefco Numbef
(Se!ecl from 0 thru 9. up lo 12 digits):
[e.g., Out 01 Area Access digit (1). Area Code, Exchange, Line Number]
Communlcatlon
PROM Data Group 4
To program. set Phone No. Selector Switch to "Secondary" and Rotary
Switch to Position 2 (Main Phone No.) on No. 690 PROM Programmer.
Baoonduy
Toleo Number
(Select from 0 lhru 9. up lo 12 digits):
*NOTES: 1. Trailing btanks are permissible for emries less than the maxi-
mum number ot digits but teading or intermediate blanks are
NOT allowed.
2. In certain Telco networks, it may be necessary to program an
11 in the position immediately following the fast digit of the
T&o Number. See Note on Page 6 for details.
Communk&on
PROM Data Group 5
To program, set Phone No. Selector Switch lo "Primary" and Rotary Switch
to Position 3 (Subs ID#) on No. 690 PROM Programmer.
Pharys-
ID" (Select from 0 thru 9):
"NOfE:
All 4 digits must be filled m. The leading digit IS not transmitted
for Ademco Low Speed. SESCOA. and Radamcs untess PROM
Data Group 12. Bit 1
IS
set.
Communlwtlon
PROM Daie Group 6
To program, set Phone No. Selector Switch lo "Secondary" and Rotary
Switch lo Position 3 (Subs IDtl) on No. 690 Programmer.
Secondary Subecrlber ID" (Select from 0 thru 9):
cl000
-NO=
All 4 digits must be tilled in. The leadmg digit
IS
not transmllled
for Ademco Low Speed, SESCOA. and Radionics unless PROM
Data Group 12. Bii 1 is set.
Communlcatlon
PROM Oate Group 7
To program. set Rotary Switch lo Position 4 ("Not Used") and raise
switches tor checked boxes representing bits set withm the hexadecimal
code.
Ademco Low Spnd/SESCOA/Radlonlcr
Raportlng Codes for
Trouble and Trouble Restore (Select from 0 thru 9. B thru F)
Trouble'
Trouble Restore'
SWITCHES
1
2
3
4
5
6
7
6
I
I
Bit deights
2
4
6
1
2
4
6
(e.g..7=1
+2+4.8=1
+2+bC=4+6,D=i
+4+&seepagel6)
CommunkaUon
PROM Dais Group 8
To program. set Rotary Switch 10 Position 5 ("Sys Opttons") ana ratse
swtches for checked boxes representing bits set wrthln the hexadecimal
_
code.
Ademco Low SpeedlSEISCOAfRadlonlt
Reporting Codes tar
Openfng and Cloelng (Select from 0 thru 9. B lhru F)
Opening'
Closng'
SWITCHES
1
2
3
4
5
6
7
6
I
I
I
I
I
I
I
Bit ieights
2
4
6'
1
2
4
6
'NOTE: The code assignments shown on page 9 are required it English
language prlntout
IS
desued
al the Ademco No. 665 or Radlomcs
No. 6000/6500 Receivers for the Ademco Low Speed, Radlontcs
"Superfast" and Radionics "BFSK" formats.
Communkeilon
PROM Data Group g
To program. set Rotary Switch lo Position 6 ("lnvened") and raise switches
for checked boxes representing bits set within the hexadecimal code.
Mulmum
Number of Altompts to DW (Select from 1 thru 15. delaulls to
6 it not programmed) and Ademco Low SPeed/SESCOA/Red)onlcr
Rqowng
Co& lor Owns
(Se&xx tram 0 mru 9. B thru F)
1
2
3
4
5
6
7
6
I
I
I
I
I
I
1
Bit ieights
2
4
6
1
2
4
6
15
Advertisement
