Advertisement
*NOTE& 1. Selecl 1 mru 8 for communicator alarm reports. Select 0 ii
communicator report not desired for a zone.
2. Note that there is no assignment of an alarm code/channel
here tor duress reporling. If any fonat othar than Adamoo
H&h Spead is utiliied. that assignment is made in the
Communication PROM. PROM Data Group 9 (see page 15).
However, ii Ademco High Speed Format is used. duress is
automatically present. The only way to suppress the duress
capability for that iormal is tor the user of the system lo
always employ user codes ending in "9".
9. ENABLE LOW BATTERY REPORTING IN ADEYCO HIGH
SPEED OR RADIONICS 'BFBK" FORMAT?
If YES. place a 1 here
lf NO. place a 0 here . . . . . . . . . . . . . . . . ..*.*.....
ENABLE THE COMMUNICATOR
TO DUAL REPORT?
If YES. place a 2 here
If NO, place a 0 here . . . . . . . . . . . . . . . . . . . . . . . . . .
ENABLE THE COMMUNICATOR
TO ALTERNATE CALLS BY
lwos7
If YES. place a 4 here
If NO. place a 0 here . . . . . . . . . . . . . . . . . . . . . . . ..-
ARE ALL THE ANSWERS TO THE PREVIOUS QUESTIONS
"NO-?
lf AU NO. place an 8 here
lf NOT ALL NO, place a 0 here . . . . . . . . . . . . . . . . . .
Add up all the numbers and place Ihe result tn the box.
Program the value in the
box.
El
10. ENABLE THE REPORTING OF AC POWER FAIL AND LOW
BA-RY
REPORTS7
If YES, place a 1 here
If NO, ptace a 0 here . . . . . . . . . . . . . . . . . . . . . . . . . .
ENABLE A ULSOQ (GRADE "A") REQUIRED SOUNDING OF AN
ALARM AFTER A SUSTAINED AC LOSS?
If YES, place a 4 here
If NO. place a 0 here . . . . . . . . . . . . . . . . . . . . . . . . . .
ARE ALL THE ANSWERS TO THE ABOVE QUESTIONS
-NO7
If ALL NO, place an 8 hare
If NOT ALL NO, place a 0 here . . ..*.............
Add up all the numbers and place the resutl in the box.
Program the value in the box.
l-l
11. ENABLE THE ALARM RELAY TO ACTlVATE DURING FIRE
ALARMS?-
It YES, place a 1 here
IfNO,placeaOhere
. . . . . . . . . -
. . . . . . . . . . . . . .
ENABLE THE EXTERNAL SIREN TO SOUND DURING FIRE
ALARMS?-
If YES, place a 2 hare
If NO, place a 0 here . . . . . . . . . . . . . . . . . . . . . . . . . .
'NOTEz One of these two selections must be YES if tire protection is
provided by the system.
LATCH THE ALARM RELAY AFTrR -MEOUT
UNTIL NUCI
DISARMED?
If YES. place a 4 here
If NO, place a 0 here . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE: In order tor this capability to Iunction. the first Rem of Entry 11
in PROM Data Group 1 or 2 or both must have a YES answer.
ARE ALL THE ANSWERS TO THE ABOVE OUESTIONS
'NO-?
If ALL NO, place an 8 here
lfNOTALLNO,ptaceaOhere
. . . . . . . . . . . . . . . . . .
Add up all me numbers and place the result in the box.
Program the value in the box.
cl
12 ZONE RESTORE ENABLE (Zones 5-8)
It none of the below is desired, DO NOT program this location.
For Zone Restore Enable. the user has the capability of ProWammin9
any cpmbination of zones described below (for zones t-4 See ltam 12.
PROM Data Group 1 on page t 1).
ZONE 5
PROGRAM A t
ZONE 6
PROGRAM A 2
ZONE 7
PROGRAM A 4
ZONE 8
PROGRAM AN 8
ZONES 5 AND 6
PROGRAM A 3
ZONES 5 AND 7
PROGRAM A 5
ZONES 5 AND 8
PROGRAM A 9
ZONES 5. 6 AND 7
PROGRAM A 7
ZONES 6 AND 7
PROGRAM A 6
cl
ff iI is desired lo program a combination not given above. a two pass
programming procedure will be required. On the first pass. program the
earker entnes of this group plus the tlrsl pass entry for this Item. On the
second pass (which should be done aWr the anttla PROM Data
Group has been programmed), repeal the pnor entries ot this group
and then program the second pass entry tor this item.
FIRST PASS
ZONES 6 AND 8
PROGRAM A 2
ZONES 5. 6 AND 8
PROGRAM A 3
ZONES 7 AND 8
PROGRAN A 4
ZONES 5. 7 AND 8
PROGRAM A 5
SECOND PASS
PROGRAM AN 8
PROGRAM AN 8
PROGRAM AN 8
cl
PROGRAM AN 8
ZONES 6. 7 AND 8
PROGRAM A 6
PROGRAM AN 8
ZONES 56.7
AND 8 PROGRAM A 7
PROGRAM AN 8 cl
Control PROM Data Gmup 3
To program. set Phone No. Seleclor Switch to "Primary" and Rotary Switch
to Posit~on 3 (Subs ID I) on No. 690 PROM Programmer.
MASTER SECURITY CODE (Select from 0 thru 9 digit set. repeating
digits permitted):
clElcl-1
Control PROM Data Group 4
To program. set Phone No. Selector Switch to "Secondary" and Rotary
Switch to Position 3 (Subs ID #) on No. 690 PROM Programmer.
NOTEz For the next 3 functions. enter zones t-8 to enable the ConsoIe key
pair or enter 0 to disable the console key pair.
1. CONSOLE 'FIRE" KEYS ASSIGNED TO ZONE
2 CONSOLE 'POLICE- KEYS ASSIGNED TO ZONE
cl
3. CONSOLE 'EMERG" KEYS ASSIGNED TO ZONE
cl
4. FAST RESPONSE ENABLE
If none of the below IS desrred, DO NOT program mis location.
For Zone Fast Response Enable. the user has the capability of pro.
gramming any combination of zones described below.
ZONE 5
PROGRAM A 1
ZONE 6
PROGRAM A 2
ZONE 7
PROGRAM A 4
ZONE 8
PROGRAM AN 8
ZONES 5 AND 6
PROGRAM A 3
ZONES 5 AND 7
PROGRAM A 5
ZONES 5 AND 8
PROGRAM A 9
ZONES 5. 6 AND 7
PROGRAM A 7
ZONES 6 AND 7
PROGRAM A 6
cl
For a combinatton not given above. follow the Iwo pass procedure 01 Item
12. PROM Data Group 2 on this page
FIRST PASS: cl
SECOND PASS:
cl
ControlPROMDataGrou~5
To program. set Rotary Switch to Position 5 (Sys Option) on No. 690 PROM
Programmer and raise switches for checked boX(eS).
TROUBLE ON OPEN SuEcf
(e.g.. tse. day/night burglary, etc.)
(check as many as desired)
zone I 1 Zone 2 Zone 3 701~ 4 Zone 5 Zone6
Zone 7 tone 8
I
Advertisement
