Related Manuals for Escea EK1250
Summary of Contents for Escea EK1250
- Page 1 Installation Instructions and User Guide EK Series Escea Fireplace Kitchen For the latest documentation, visit www.escea.com 630451_1...
- Page 2 Escea will not be accountable for any such failings or their consequences. Manufactured by: Escea Ltd, PO Box 5277 Dunedin NZ, Ph: +64 3 478 8220 For contact details of your local Escea distributor or dealer, please visit www.escea.com or email us at info@escea.com.
- Page 3 WARNING FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY DAMAGE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY ALSO VOID YOUR FIRE INSURANCE AND/OR WARRANTY. A LIT FIRE MUST NEVER BE LEFT UNATTENDED. THE FIREPLACE MUST ONLY BE USED FOR COOKING/HEATING AS INTENDED. MAINTAIN AND OPERATE THE FIREPLACE IN ACCORDANCE WITH THESE INSTRUCTIONS.
-
Page 4: Table Of Contents
Installation Process and Product Details Product Description Product Dimensions Safety Clearances to Combustibles Clearances to Combustible Surfaces Non-Combustible Cavity Installation Minimum Requirements of the Cavity Sealing Requirements Installing the Flue System Flue Specifications Assembling and Installing the Fireplace Gather Installation Securing the Base of the Appliance Assembling the Fireplace Attaching and Removing the Pivot Drawer... -
Page 5: Installation Process And Product Details
It is designed for outdoor use ONLY. Product Dimensions The EK series consists of three different sizes of fireplace: the EK950, the EK1250, and the EK1550. Dimensions for each fireplace can be found on the next pages. - Page 6 EK1250 1296 1219 1247 Flue: 350 ID WEIGHT: 380KG...
- Page 7 EK1550 Note: The EK1550 requires two flues to function properly - this is mandatory. 1596 1519 1547 Flue: 350 ID Flue: 350 ID WEIGHT: 450KG EK Installation Manual 630451_1...
-
Page 8: Safety Clearances To Combustibles
Safety Clearances to Combustibles Clearances to Combustible Surfaces Note: The concrete structure shown below must comply with section “C1 Minimum Requirements of the Cavity” on page 9. -
Page 9: Non-Combustible Cavity Installation
Non-Combustible Cavity Installation Minimum Requirements of the Cavity This appliance is designed for outdoor use ONLY. When the appliance forms part of a building, or is installed attached to the building, then the entire appliance must be fully enclosed in concrete material (concrete block and/or poured concrete) of 140mm thickness or greater. -
Page 10: C2 Sealing Requirements
The air vent(s) can be any size or shape, provided that the total combined open surface area is at least 28000mm Note: The EK1250/EK950 are shown as an example; the EK1550 requires two flues. A total open surface area of... -
Page 11: Installing The Flue System
Note: The EK1550 will require two of each item shown below (two flue terminals, two cones, etc.). The EK1250 and EK950 require one of each item shown below. NOTE: THE APPLIANCE & FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/... -
Page 12: Assembling And Installing The Fireplace
Assembling and Installing the Fireplace Gather Installation CAUTION: Team or mechanically aided lift required for gather. Gather Weight EK950: 60 kg EK1250: 80 kg EK1550: 120 kg Once the gather is in place, attach using the bolts, nuts, and washers provided. -
Page 13: E2 Securing The Base Of The Appliance
Securing the Base of the Appliance Remove the shaded parts below to access the securing holes. The EK1250 has been used as an example; the EK950 and EK1550 would be secured in the same manner. Secure the appliance base suitably using any 4 of the holes circled below. -
Page 14: E3 Assembling The Fireplace
Assembling the Fireplace The EK1250 has been used as an example in the images below. The EK950 will have one fewer panel and racking strip; the EK1550 will have one more panel and racking strip. Note: For the EK950 there is no end spacer - cut bricks are supplied... -
Page 15: E4 Attaching And Removing The Pivot Drawer
Using the Weather Cover (Optional Accessory) The weather cover (shown below) provides protection from the elements for the interior of the firebox. EK Installation Manual 630451_1 It is an optional accessory that can be purchased from your local Escea dealer. Ensure that the firebox... -
Page 16: Burning Guide
is cool prior to fitting the weather cover. To install the weather cover, position the hooks at the bottom of the weather cover on the pins located on either side of the pivot drawer of the fireplace, as shown below. With the bottom hooks in place, rotate the weather cover up until it slides into the top, as shown below. -
Page 17: F1 Fuel Selection
Fuel Selection For optimal wood burning, use firewood with a moisture content of less than 20%. Starting the Fire If you are starting your fire for the purpose of cooking, then please proceed to section “G Cooking Guide” on page 17. To start the fire, stack kindling so that it leans against the back panels, allowing sufficient airflow between pieces. -
Page 18: G1 Cast Iron Instructions
Cast Iron Instructions All cast iron parts lock into the grill frames provided with the appliance. Ensure that they are securely set prior to cooking. The cast iron parts supplied are coated in a vitreous enamel. In the event of decay or chipping, the cast iron can be seasoned by rubbing a thin layer of oil on the cast iron and heating the surface. - Page 19 warmer grill, position the cooking grills closer to the bottom of the fire. For lower heat, position the cooking grills higher. For the slotted grill, it is best to position the fat drip tray on the front of the grill prior to cooking. The fat drip tray will collect any grease drips to provide easy cleanup.
-
Page 20: H Maintenance
Once you have finished cooking, remove all cooking trays and the ember generator prior to using the fire for standard outdoor heating. Use the provided gloves when handling the hot cooking trays and the ember generator. Heat will begin to transfer through the gloves after 30 seconds. It is recommended to move the hot trays within 30 seconds. -
Page 21: H1 Chimney Maintenance
H2 Recommended Refurbishment Products Stovebright Metallic Black Spray Paint This product may be used on all black painted surfaces and is available from your Escea dealer. Before application, ensure any corrosion is removed by a wire brush; also ensure that the surface is clean and free of any dust. - Page 22 Escea dealer. Nature of Warranty Subject to the exclusions in section 2 & 3, Escea may undertake to put right any defects in the Escea Outdoor Wood Fire products supplied by Escea for the periods specified below:...
- Page 23 Damage caused by abnormally corrosive environments (e.g. sea salt corrosion). Escea wood fires are coated with high temperature paint that may show signs of surface rust if exposed to moisture for an extended period of time. Any repair and replacements of parts that are subject to normal wear and tear expected with any outdoor fire product.
- Page 24 Escea product. Escea may charge you a service call fee if a repairer will be required to travel more than 30 km from the nearest service centre to your location. You can obtain details on the location of service centres and service call fees by visiting the Escea website or calling the customer care line below.
Need help?
Do you have a question about the EK1250 and is the answer not in the manual?
Questions and answers