Advertisement
Advertisement
Table of Contents
Related Manuals for Sunny Health & Fitness SF-T7723
Summary of Contents for Sunny Health & Fitness SF-T7723
-
Page 1: User Manual
FORCE FITMILL SF-T7723 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669). -
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. -
Page 3: Exploded Diagram
EXPLODED DIAGRAM 19 19... -
Page 4: Hardware Package
HARDWARE PACKAGE #31 M8x45x20 4PCS #32 M8x15 4PCS #28 φ8.2xφ16.2x1.5 8PCS #29 M8 2PCS #38 M8x85x20 4PCS #40 φ8xφ20x1.5 10PCS #39 M8x50x20 4PCS #36 1PC #37 φ12xφ28x2.0 1PC #45 S6 1PC #46 S13-14 1PC #47 S17-S19 1PC #48 S5 1PC Ordering Replacement Parts (U.S. -
Page 5: Parts List
PARTS LIST Description Spec Description Spec Main Frame Phillips Self Drilling Screw ST4.8x16 Bottom Frame Transportation Wheel Stabilizer Tube Socket Pan Head Screw M8x40x15 φ8.2xφ16.2x1.5 Rear Handlebar Flat Washer Front Handlebar Nylon Nut Phillips Pan Head Self Middle Handlebar ST5.5x22 Drilling Screw Bottom Handlebar Socket Pan Head Bolt... -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTIONS STEP 1: #31 M8x45x20 2PCS #32 M8x15 4PCS Remove 2 Socket Pan Head Bolts (No. 31), 4 #28 φ8.2xφ16.2x1.5 8PCS Socket Pan Head Screws (No. 32), 8 Flat #29 M8 2PCS Washers (No. 28) and 2 Nylon Nuts (No. 29) #46 S13-14 1PC from Stabilizer Tubes (No. - Page 7 STEP 3: #36 1PC Attach Main Frame (No. 1) to Bottom Frame (No. 2) with 1 Round Knob (No. 36) and 1 Flat Washer (No. 37). Then tighten and secure with Round Knob (No. 36). #37 φ12xφ28x2.0 1PC 36 37 STEP 4: #38 M8x85x20 2PCS Insert Rear Handlebars (No.
- Page 8 STEP 5: #38 M8x85x20 2PCS Remove 4 Socket Pan Head Bolts (No. 39), 4 Arc Washers (No. 40) from Middle #39 M8x50x20 4PCS Handlebars (No. 6) with Allen Wrench (No. 48). #40 φ8xφ20x1.5 6PCS Attach Middle Handlebars (No. 6) to Front Handlebar (No.
-
Page 9: Folding Instructions
FOLDING INSTRUCTIONS Folding: To fold up the treadmill, loosen and pull out Round Knob (No. 36) and Flat Washer (No. 37). Lift up on the rear end of Main Frame (No. 1) until the Cylinder (No. 15) lock into the tube. - Page 10 HOW TO MOVE THE TREADMILL Before attempting to move the treadmill, please make sure that it has been properly folded. To tilt, start by placing one hand at Rear Handlebar (No. 4) to support the treadmill. Next, place one foot on position “A” to hold the bottom end of the treadmill steady.
-
Page 11: Maintenance Instructions
MAINTENANCE INSTRUCTIONS CENTERING THE WALKING BELT: If the walking belt is off centered, the unit will make noise. Please use the tool to re-adjust the walking belt if it is too loose or too tight. 1. When the walking belt moves to the right side, please turn the right side hexagon socket screw clockwise 1 or 2 circles, and then turn back a little bit. -
Page 12: Treadmill Lubrication
TREADMILL LUBRICATION To reduce the friction of the walking belt and minimize wear, lubricant may be applied directly onto the treadboard and underside of the walking belt. Lift one side of the walking belt and touch the top surface of the treadboard. If the surface is wet, no lubrication is required.