CTC Union FRM220-10/100i(S)-2E-DC12 User Manual

Introduction
The FRM220 Family are slide-in-line cards for placement in the FRM220 Platform
Media Converter Chassis and available in a number of different models that also act
as a stand-alone converters when placed in a one-slot chassis. The 10/100i(S)-2E is a
two UTP plus Fiber media converter/switch for 10Base-T or 100Base-TX data
transmission over 100Base-FX optical fiber media. Depending on your specific network
needs, these converters are available with either multi-mode or single-mode fixed
optical transceivers with connectors for SC, ST or FC. In single mode, WDM (Wave
Division Multiplexing with SC connector) is also available in 20, 40, 60, or 80Km reach,
which will provide the ability to transmit and receive data using only a single optical
fiber. The 10/100iS-2E model sports an SFP cage to accept industry standard SFP
optical modules.
When the 10/100i(S)-2E card is placed in the FRM220 rack with NMC, the in-band
management, can monitor, configure and control the activity of each port for both local
and remote sides. For the UTP side, auto-negotiation is default. You may set data rate
to 10Mbps or 100Mbps and duplex mode to full or half duplex through forced mode
setting on either UTP port. Added features such as stand-alone console management
(when installed in CH01M chassis) all advanced features such as ingress/egress
bandwidth control, 802.3X flow control and 802.1Q VLAN. Six LED indicators signal
the power status of the converter, UTP port speed, duplex status and Link/Act and FX
port Link/Act and FEF (Far End Fault).
Features
Auto-negotiation or manual mode for each TP port
Link Fault Pass-through (LFP) function
Far End Fault on fiber port
802.3X pause control on TP
Compatible with FRM220 Chassis in-band management
Bandwidth control (32K or 512K x N)
Maximum MTU supports 2046 bytes frame size
Supports 802.1Q tag VLAN and VLAN pass-through
Supports local and remote monitoring (Link/Speed/Duplex/Power)
Supports local and remote configuration (all parameters)
Dying gasp feature to report remote unit power failure
Supports Auto Laser Shutdown (ALS) feature
Online firmware upgrade (local or remote) when in FRM220 chassis
Panel
Figure #1. Front Panel of FRM220-10/100i(S)-2E
Figure #2. Rear Panel of Stand-alone FRM220-10/100i(S)-2E-DC12
FRM220-10/100i(S)-2E-AC/DC48/AD/AD-M

User Guide

In-band Managed Fiber Media Converter/Switch
2 x 10/100Base-TX / 100Base-FX – FRM220-10/100i(S)-2E
Specifications
Standards
IEEE802.3 10Base-T, 802.3u 100Base-TX & 100Base-FX, 802.3X, 802.1Q
Auto or Full/Half/10/100 Forced mode supported
Maximum MTU size up to 2046 Bytes
10/100Base-TX Connectors
Two RJ-45 connectors are provided for connection to MDI-X (to PC) or MDI (to switch)
Fiber
equipment. Auto MDI-X allows all UTP connections to be made using standard
Connections
straight-through UTP cable.
LEDs 100Base-TX UTP Cable
Cable type should be Cat.5 or better
Ethernet Cable distance should not exceed 100 meters
Connections
Fiber Optic Connectors
FRM220-10/100i-2E : Fixed transceivers available with SC, FC or ST connections
FRM220-10/100iS-2E : SFP cage to support MSA Fast Ethernet or STM-1/OC3 optics
Environment
Operating temperature : 0 ~ 50C, Storage 0~70C
Humidity : 5-~90% (non-condensing)
Power
Adapter: 100~240VAC input to 12VDC @ 1000mA output
AC Chassis: Built-in power supply for 100~240VAC input
DC Chassis: Built-in power supply for 18~72VDC input
AD Chassis: Both AC and DC power supplied built-in
Dimensions: (W x D x H) mm
10/100i(S)-2E-DC12 : 88 x 160 x 24
Built-in power types : 135 x 201 x 35
Management Features
The 10/100i(S)-2E is designed to be placed either in a stand-alone chassis with
serial console management port or in the FRM220 managed chassis. As a remote unit,
it may be placed in any single-slot chassis. When placed in a stand-alone chassis with
DB9 console port, these devices support a text based serial terminal with an easy to
use menu system for configuration. When placed in a managed rack, the card is
configured and monitored through the chassis NMC (network management controller)
via console, Telnet, Web HTTP or SNMP.
sales@ctcu.com
V 1.1