Foscam FI9826P Quick Installation Manual

Quick Installation Guide
（For Windows & Mac OS）
Indoor HD Wireless IP Camera with P2P
Ethernet Cable
V4.8
EQ982117
3
1. Enable the DHCP feature of your router (Enabled by default
normally), then open the IP Camera Tool program. It should
display the camera's IP address in your LAN (Local Area Network).
2. Double click the camera list here, and your default browser
will open up to the camera's login page. When logging in for the
first time, you will need to download and install the add-on.
Take Microsoft Internet Explorer as an example. For Google
Chrome, Apple Safari, or Mozilla Firefox, please refer to the User
Manual.
Note：
Doesn't support 64-bit browser.
ShenZhen Foscam Intelligent Technology Co., Ltd
www.foscam.com
1
Package Contents
IP Camera Power Adapter Resource CD
Mounting Bracket Wi-Fi Antenna
LAN
Quick Installation Guide
（For Windows & Mac OS）
Indoor HD Wireless IP Camera
Quick Installation Guide Warranty Card
3. After installing the add-on, refresh the browser and click
Access the IP Camera
Login.
in LAN
4. When you login for the first time, it will request that you
modify the default username and/or password. Input the New
username, New password, and Confirm the password
Modify to complete the modification. You will now use the
new username and password to login to the camera in the
future.
Click Install
Hardware Introduction
Physical Description
Mounting Port
Reset Button
Speaker
LENS
Infrared LED
Microphone
1. Mount the antenna and make it stand vertically.
2. Connect the camera to the LAN network (Router or Switch) via
network cable.
3. Connect the power adapter to the camera.
LAN
ANT
Antenna
DC 5V I / O Alarm I / O Alarm ANT Antenna
WPS AUDIO
SD Input DC 5V
Power
IN IN/OUT
OU T
WPS OUT IN Micro SD
Power
Output SD Card Slot
SD Card Slot WPS
Network light
Network light
Power light Power light
WPS
FI9815P Supports I/Oalarm
Default username is admin with
no password.
Main stream offers the highest
quality video while Sub stream
offers less quality, but also less
delay when viewing.
click
,
Notes:
automatically. Please set the basic parameters, such as camera
name, camera time, wireless settings and so on.
the reset button on the bottom of the camera using a pin for 5
seconds. This resets the camera to factory defaults.
Input the New username,
please continue with the setup by following the Wireless and
New password and
Confirm the password.
Remote Access steps below.
Hardware Connection
ANT
o WPS AUDIO
SD
OUT IN
WPS
5. After logging in, you will see live video on the interface.
After logging in for the first time, it will go to "Setup Wizard"
If you forget your username or password, you can press and hold
If you want to access your camera over wireless or the Internet,
2

Software Installation

1. Insert the CD into the CD drive of your computer.
2. Go to the folder "IP Camera Search Tool" and find the folder
"For Windows OS"or "For Mac OS". Copy and paste the IP camera
tool file to your computer, or drag it onto your desktop.
Shortcut icon for Windows OS Shortcut icon for Mac OS
Notes:
If your computer ( Windows OS ) supports autorun function,
you can find the corresponding file in the opened control
panel.
If your computer does not have CD drive, you can download
the IP camera tool from our website: www.foscam.com for free.
4

Wireless Connection

Your camera supports wireless connection (camera with PoE
does not support wireless connection). You could use either
of the following two ways to connect cameras and the
internet.
WPS (Wi-Fi Protected Set-up) connection: your wireless
router supports WPS function.
Configure the wireless connection manually: your wireless
router does not support WPS function.
★ WPS Connection
Before using the WPS connection, the matters need attention.
Please make sure that your router supports WPS function,
and has been connected to the network.
If the camera have connected the network cable, please
disconnect it.