Brother MD-602 Service Manual page 28

No. Key name
y
Fixed stitch key
u
Name label key
i
Pleat presser
sewing key
o
AUTO key
!0 0
Thread trimming
key
!1
Sewing speed key
!2
Sewing speed
indicator
!3
Backtack indicator
!4
Slow start key
!5
Correction key
!6
Needle up/down
key
!7
Half stitch key
22
When this key is pressed, the number of stitches for seam E (01 – 99) is sewn.
To sew start backtack stitches at this time, press the start backtack key e. The number of
start backtack stitches are set by A and B.
To sew end backtack stitches at this time, press the end backtack key r. The values for C
and D become the number of end backtack stitches when fixed stitch sewing is off.
When this key is pressed, the number of stitches for seams E and F (01 – 99) will each be
sewn twice.
To sew start backtack stitches at this time, press the start backtack key e. The values for A
and B become the number of start backtack stitches when name label sewing is off.
To sew end backtack stitches at this time, press the end backtack key r. The values for C
and D become the number of end backtack stitches when name label sewing is off.
When this key is pressed, the number of stitches for seam E (01 – 99) is sewn when the
actuator is pressed.
To sew start backtack stitches at this time, press the start backtack key e. The number of
start backtack stitches are set by A and B.
To sew end backtack stitches at this time, press the end backtack key r. The values for C
and D become the number of end backtack stitches when pleat presser sewing is off.
When this key is pressed, machine operations (start backtack sewing, end backtack sewing,
fixed stitch sewing and thread trimming) will be automatically carried out up until the set
position when the treadle is depressed.
This key is only valid when the continuous backtack key t, fixed stitch key y or name label
key u has been pressed.
When this key is pressed, the thread is trimmed after sewing is completed.
This key is only valid when the fixed stitch key y or name label key u has been pressed.
When this key is pressed, the sewing speed indicator !2 will illuminate and the sewing
speed will be shown in the LED display q. You can then set the sewing speed by setting
the respective values for A, B, C and D.
If this key is then pressed again, the backtack indicator !3 will illuminate and the backtack
sewing speed will be shown in the LED display q. You can then set the sewing speed by
setting the respective values for A, B, C and D.
If this key is then pressed again or if the machine is started, the LED display q, sewing
speed indicator !2 and backtack indicator !3 will all switch off.
When this key is pressed, the first two stitches at the sewing start (after the thread has been
trimmed and the needle has been raised) are sewn at low speed.
When set to ON, correction sewing is carried out at low speed when the quick reverse
switch is pressed. This function cannot be used after thread trimming.
If the quick reverse switch is pressed while the sewing machine is operating, reverse feed
will be carried out.
The " " and " " indicators illuminate each time this key is pressed.
If the treadle is pressed to the neutral position while the "
needle will rise above the needle plate and stop (needle up stop).
If the treadle is pressed to the neutral position while the "
needle will drop below the needle plate and stop (needle down stop).
This key is used to raise or lower the needle when machine operation is interrupted.
Function
MD-602, 612
" indicator is illuminated, the
" indicator is illuminated, the