In-situ TROLL 9500 Quick Start Manual

Your new Multi-P arameter TROLL 9500 arrives with the following installed:
• Removable Basic sensors pH, ORP, Polarographic Dissolved Oxygen, Conductivity (as required)
• Alkaline batteries—if shipped with Polarographic DO sensor, to keep the sensor conditioned
• Permanent sensors Barometric Pressure, Temperature, Pressure/Level (optional), Turbidity (optional)
The Cal Cup is attached with water in the bottom to keep the sensors hydrated
1
to your local hard drive from
Install Win-Situ ® 4
the In-Situ software CD or the In-Situ website.
Optional: Install the desktop component of Pocket-
Situ 4 to the same computer. Then use the In-Situ Software
Manager to install it on the RuggedReader
ActiveSync ® connection.
Tip: If using a USB TROLL Com, be sure to
select the option "Install USB TROLL Com
Drivers" when installing Win-Situ.
4
Plug the TROLL Com into a USB or serial port
on a desktop/laptop PC, or into the serial port
on a RuggedReader handheld PDA.
5
Launch the software—
: Double-click the desktop shortcut
Win-Situ
On first connection, be sure to select the
correct COM port for a USB connection.
Set up the port for a Direct connection to
device at
One 19200
6
Connect to the TROLL 9500—
A
Win-Situ 4
7
When connected, the device appears in the Navigation tree
below the COM port. Select the TROLL and set its clock—
Select the TROLL. The software retrieves and displays informa-
A
tion about the device and all installed sensors. This can take a
moment . . .
Select
B Edit
C In the next screen, select the
Follow the Wizard to synchronize the device clock with the PC
D
clock
8
Quick-Cal the Basic water quality sensors
A Detach the Cal Cup. Empty out liquid and remove small sponge (if present). Rinse
sensors with DI water
B Fill Cal Cup to the line with Quick Cal solution and re-attach—not too tight
Establish software connection as above. Select Parameters in the Navigation tree
C
Click or tap . Select sensors to calibrate. Click or tap
D Quick Cal
ORP, and Conductivity calibration
: Turn probe upside-down and pour out some solution so
E For Polarographic DO
DO sensor membrane is in air and temperature sensor is completely covered. Re-
attach cap loosely. Select vented cable or supply barometric pressure for accurate
results. Select Run to complete DO calibration. Details are in Section 3 of the
Operator's Manual
Remove Cal Cup, pour out the Quick Cal solution, rinse the front end of the probe,
F
and attach the restrictor
2
at your next
®
Tip: After plugging in a USB TROLL Com, follow the prompts
to install the drivers. Then use Windows
determine which COM port the USB TROLL Com is using.
OR
.
baud.
Highlight the
A COM
Click or tap
B Find
B
Clock option
Install batteries:
A Remove battery compartment cover
B Insert batteries
C Replace cover and tighten
A
C
B
Device Manager to
®
: Tap the Start menu, tap Pocket-Situ 4
Pocket-Situ
Set up the port with a
TIP:
to device at
One 19200
port in the Navigation tree
A
Pocket-
Situ 4
B
A
B
to start pH,
Run
B
Multi-Parameter Water Quality TROLL
MP TROLL 9500
Quick STaRT Guide
3
a TROLL Com to the TROLL
Attach
9500 or to its cable.
Mating the Twist-Lock connectors is
easy after you do it once. Detailed
steps and photos are on the back of this
Quick Start Guide.
USB or Serial port
connection
Direct
baud
RuggedReader clock. Set
it first if wrong (Start Menu
> Settings > System tab >
compartment
Clock)
C
E
D
®
Serial
port
Battery
Sealed
body
Restrictor
Nose cone