Table of Contents
Advertisement
New Hallingford
3 Door 3 Drawer Wardrobe
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Dimensions
Width - 148,8cm
Depth - 60,3cm
Height - 205,7cm
Important
- Please read these instructions before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
03456 400 800
- Please keep for future reference
2278380
2745253
2749716
2482279
2448282
Issue 1 - 10/06/14
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Argos New Hallingford 3 Door 3 Drawer Wardrobe
Summary of Contents for Argos New Hallingford 3 Door 3 Drawer Wardrobe
- Page 1 New Hallingford 3 Door 3 Drawer Wardrobe Assembly Instructions 2278380 - Please keep for future reference 2745253 2749716 Tip : To prevent damage, we recommend that you 2482279 build your unit on the 2448282 carton(s) it was packed in. Dimensions Width - 148,8cm Depth - 60,3cm Height - 205,7cm...
- Page 2 Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the • Do not stand or put weight on •To reduce the likelihood of components and tools listed on the product, this could cause damaging your damage.
- Page 3 Components - Panels If you have damaged or missing components, call the Customer Helpline: 03456 400 800 Please check you have all the panels listed below Door x 2 Left side Right side Upright (205.6 x 58cm) (205.6 x 58cm) (196.9 x 57.6cm) (199.2 x 48.8cm) P2349b...
- Page 4 Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. FK1324 FK1980 FK1981 40mm Screw x 9 20mm Screw x 12 9mm Srew x 6 FK1301...
- Page 5 Assembly Instructions Step 1 Drawer assembly x 3 Insert two small locking nuts J into drawer wrap Make sure the ‘arrow’ on J is pointing towards the hole in the edge of 0 Screw 24mm locking screws H into holes shown on back of drawer front !.
- Page 6 Assembly Instructions Step 1 - continued Turn the drawer wrap assembly over and push onto drawer front !. Use a philips or flatblade screwdriver, that is a good fit, to turn small locking nut J as far as it will go - more than 1/2 turn.
- Page 7 Assembly Instructions Step 2 - Step 2 - continued continued Slide top of runners R back. Fix through 3rd hole of runner R and pre-drilled holes of upright 3 using 10mm fixing screw drawer Fix through 1st and 9th hole of runners R using 15mm screw O.
- Page 8 Assembly Instructions Step 4 Attaching plinths Align the sides of plinth front ^ with bottom 5 as shown and attach using 40mm screw A. Note: there are no Top side predrilled holes for 40mm screw aA. Note: top and bottom panels 5 are identical.
- Page 9 Assembly Instructions Step 7 Step Insert locking screws Screw 24mm locking screw H into top 5. Unfinished back edge Step 8 Attaching panels Two people are needed here. Position top 5, large horizontal 7 and small horizontal 8 onto upright Insert two Large locking nuts I into upright 3, 3 in large horizontal 7 and 2 in...
- Page 10 Assembly Instructions Step 10 Attaching panels Two people are needed here. Position upright small 6 onto bottom 5 and small horizontal 8. Insert two Large locking nuts I into upright small 6 and small horizontal 8 where shown. Use a screwdriver to turn locking nuts I clockwise to lock.
- Page 11 Assembly Instructions S S tep 12 Attaching panels Two people are needed here. Position right side 2 and left side 1 onto top and bottom Insert six Large locking nuts I in top and bottom 5, insert 2 large locking nuts I into large horiziontal 7.
- Page 12 Assembly Instructions Step 14 Attaching pelment and L-bracket Position pelment * onto top 5 as shown, fix by using three 40mm screws Step 15 Insert shelf Position shelf @ onto board carriers N and fix by screwing four 15mm screws O through board carrier N into shelf @.
- Page 13 Assembly Instructions Step 16 Inserting drawers Pull runners out. S lide drawers onto runners so they butt up against back of drawer front. 1st small threaded hole Fix through drawer sides into runners using 9mm screws Step 17 Inserting hanger rails Place hanger rails U and V onto hanger rail supports M.
- Page 14 Assembly Instructions Step 19 Hanging doors With help, slot hinge door Q onto hinge back Tighten screw shown to lock hinges in position. Repeat a and b for other doors. See ‘Hinge adjustment’ in step 20 if the doors need adjusting. Position L-Bracket G onto top 5 as shown, fix by using15mm screw D.
- Page 15 Assembly Instructions Step 20 Hinge adjustment To move doors up or down: loosen screws shown and move doors to suit. Once doors are aligned, re-tighten. To move doors in or out: loosen screw shown and move doors to suit. Re-tighten screws. To move doors left or right: loosen screw shown and move doors...
- Page 16 A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Need help?
Do you have a question about the New Hallingford 3 Door 3 Drawer Wardrobe and is the answer not in the manual?
Questions and answers
Can we get a video on how to assemble
To assemble the Argos New Hallingford 3 Door 3 Drawer Wardrobe:
1. Preparation:
- Assemble on a soft, level surface to avoid damage.
- Keep children and animals away.
- Lay out all parts and ensure you have enough space.
- It is easier with two people.
2. Drawer Runners (Step 2):
- Slide the top of runner R forward and fix to upright 3 using 10mm fixing screw E.
- Slide runner R back and fix using screws E in the 3rd hole and 15mm screws O in the 1st and 9th holes.
- Repeat on upright small 6. Note: No pre-drilled holes for 15mm screws.
3. Insert Locking Screws (Step 3):
- Screw 24mm locking screw H into upright 3.
4. Bottom Panel (Step 5):
- Insert locking screws H into bottom panel 5.
5. Attach Upright to Bottom (Step 6):
- Position upright 3 on bottom panel 5.
- Insert large locking nuts I into upright and turn clockwise to lock.
6. Top and Horizontal Panels (Step 8):
- With two people, position top 5, large horizontal 7, and small horizontal 8 onto upright 3.
- Insert large locking nuts I where shown and turn clockwise to lock.
7. Insert Locking Screws into Upright 6 (Step 9):
- Screw 24mm locking screw H into upright small 6.
Continue following the instructions on the next steps as outlined in the manual. Use a damp cloth and mild detergent for cleaning and check for loose screws over time. Do not discard with household waste.
This answer is automatically generated