ZooZ ZSE18 User Manual

USER MANUAL FEATURES SPECIFICATIONS
Fast, reliable motion detection Model Number: ZSE18
4 4
4 Built-in vibration sensor 4 Z-Wave Frequency: 908.42 MHz
4 Latest S2 security protocol and 4 Power: 1 CR123A battery (3V) or
AES-128 signal encryption micro USB
MOTION SENSOR
4 2 alternative power sources: 4 Range: Up to 100 feet
ZSE18
battery or micro USB 4 Operating Temp.: 32-104° F
Installation and Use: Indoor only 1. Bring the sensor within direct
Auto-inclusion for instant set-up
4 4
4 Visual range test tool
Z-WAVE CONTROL
4 Magnetic mount for quick and
flexible installation
ADD DEVICE to your hub
Adjustable LED indicator
4
Initiate inclusion (pairing) in
4 Low battery alerts
the app (or web interface).
Z-Wave Plus with improved 500
4
www.getzooz.com chip for faster and safer wireless
Twist open the cover of
communication the sensor to access
the battery.
confirm inclusion.
PULL BATTERY TAB OUT EXCLUSION (REMOVING DEVICE)
3. A new motion sensor will appear
1. Bring the sensor within direct
Activating the battery will
in your device list.
automatically put the sensor range of your Z-Wave gateway
into inclusion mode. If it's not Z-Wave button
USB
controller (hub).
port
added within 30 seconds, try
2. Put the Z-Wave hub into
resetting it and including it manually.
exclusion mode (not sure how to
MANUAL INCLUSION (PAIRING)

TROUBLESHOOTING

do that? ask@getzooz.com).
3. Press and release the Z-Wave
The sensor won't add to the hub?
range of your Z-Wave gateway button on the sensor 3 times as
Try this:
(hub).
quickly as possible.
1. Initiate EXCLUSION and click the
2. Put the Z-Wave hub into 4. Your hub will confirm exclusion
Z-Wave button 3 times quickly.
inclusion mode (not sure how to and the device will disappear
Then try adding it again.
do that? ask@getzooz.com).
from your controller's device list.
2. Bring the sensor closer to your
3. Press and release the Z-Wave
Z-Wave hub.
button 3 times quickly. The LED
3. Click the Z-Wave button on the
indicator will start blinking fast
If your primary controller is missing
sensor 4-5 times VERY quickly
and turn solid for a second to or inoperable, you may need to
when adding it.
reset the device to factory settings. During wake-up, the sensor recei-
To complete the reset process ves communication from the hub
manually, press and HOLD the Z- (setting updates or network infor-
Wave button on the sensor for at mation). Long wake-up interval will
least 20 seconds. The LED indica- not affect how o en the sensor
tor will flash, stay solid, and then reports motion or vibration to your
turn off to confirm factory reset. gateway (hub).
MANUAL WAKE-UP
NOTE: All previously recorded activity
Press and HOLD the Z-Wave button
and custom settings will be erased from
for 5 seconds to wake the device
the device's memory.
up. The LED will start flashing.
WAKE-UP MODE
You may need to wake the sensor
up manually IF:
The sensor's wake-up interval is set
1. It doesn't fully configure during
to 12 hours by default to save
set-up (status is not displayed or
battery life. You can change the
FACTORY RESET
errors pop up in your hub's
wake-up interval in advanced
interface).
settings if available in your system.
2. You change advanced settings for
POSITIONING
the sensor and want them to Attach your sensor to
This product should be installed
4
update. the magnetic base and
indoors upon completion of any
position it to cover the
building renovations.
MOUNTING
area you wish to moni-
4 Do not install the sensor in a place
with direct sun exposure, high
tor. For best results, mount the
RECOMMENDED: Use the mount-
temperature, or humidity.
sensor within 0 feet from the door 2
ing screw to securely attach the
4 Keep away from chemicals, water, and
and around 7 feet from the ground.
magnetic base to a flat surface of dust.
MOTION DETECTION RANGE Ensure the device is never close to any
your choice. 4
heat source or open flame to prevent
13 FEET
120°
fire.
4 Ensure the device is connected to an
OR:
25 FEET
electric power source that does not
Use the adhesive tape to stick the
exceed the maximum load power.
120°
base to a clean surface
13 FEET 4 No part of the device may be replaced
See Settings for ways to optimize or repaired by the user, except for the
for quick and hassle-
battery.
free installation. and customize motion detection
and activity reports.
WARNING