Supermicro X11SSH-CTF Quick Reference Manual

S
C
UPERMICR
ontaCt
R
• Website: www.supermicro.com
• General Information: marketing@supermicro.com
X11ssH-Ctf/tf
• Technical Support: support@supermicro.com
Q r g 1.0a
uICk eferenCe uIde • Phone: +1 (408) 503-8000, Fax: +1 (408) 503-8008
Motherboard Layout and Features
VGA
JOH1
JPME2
LEDBMC
JIPMB1
JPTG1
USB2/3
JD1
SAS CODE
MH8
BT1
X11SSH-TF
Intel
PCH
J24
LE3
LEDS1
LSI3008
JSD2
(-CTF only)
JSD1
JSAS1
FANA
PRESS FIT
Heatsink Installation
CPU Installation
Socket Key
Press down
and turn
clockwise
Pin 1
Apply thermal
CPU Key
grease
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
guide.
I
nformatIon
COM1
JPCK1
J2
USB6/7 COM2
(3.0)
IPMI_LAN
LAN1
LAN2
USB0/1
X550 JTPM1
JPWR2
JI2C2
JPWR1
SP1
REV:1.01
DESIGNED IN USA
CPU Socket LGA1151
JF1
BAR CODE
JPI2C1
LEDPWR
FAN1
FAN2
MAC CODE IPMI CODE
Front Panel Control (JF1)
1 2
PWR Power Button
Ground
Reset Reset Button Ground
Power Fail LED
3.3 V
5V Stby OH/Fan Fail
3.3V Stby NIC2 Active LED
3.3V Stby NIC1 Active LED
ID_UID_SW/3.3V Stby HDD LED
3.3V PWR LED
NMI Ground
19 20
f ,
or your system to work ProPerly Please download aPProPrIate
/ / '
drIvers Images user s manual from tHe lInks below
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com/CDR_Images/CDR-X11-UP/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
Connectors and LED Indicators
Jumpers
Jumper Description Default Setting
JBR1 BIOS Recovery Pins 1-2 (Normal)
JBT1 CMOS Clear Open (Normal)
JI 2 C1/JI 2 C2 SMB to PCI-E Slots Enable/Disable Pins 2-3 (Disabled, Default)
JPB1 BMC Enabled Pins 1-2 (Enabled)
JPCK1 LANCONF Flash Pins 2-3 (Disabled, Default)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPME2 Manufacturing Mode Pins 1-2 (Normal)
JPS1 SAS 3.0 Enable/Disable (X11SSH-CTF only) Pins 1-2 (Enabled)
JPSAS1 SAS HDD Enable/Disable (X11SSH-CTF only) Pins 1-2 (Enabled, Default)
JPTG1 10Gb LAN Enable/Disable Pins 1-2 (Enabled)
JVRM1 VRM SMB Clock (to BMC or PCH) Pins 1-2 (BMC, Normal)
JVRM2 VRM SMB Data (to BMC or PCH) Pins 1-2 (BMC, Normal)
JWD1 Watch Dog Pins 1-2 (Reset)
Connectors
Connector Description
BT1 Onboard Battery
COM1/COM2 COM Port/COM Header
FAN1 ~ FAN5, FANA System/CPU Fan Headers (FAN1: CPU Fan)
IPMI_LAN Dedicated IPMI LAN Port
I-SATA0 ~ I-SATA7 Intel PCH SATA 3.0 Ports
I-SGPIO/I-SGPIO2 Serial Link General Purpose I/O Headers
J24 M.2 PCI-E 3.0 X4 Slot
JD1 Power LED/Speaker Header (Pins 1-3: Power LED, Pins 4-7: Speaker)
JF1 Front Control Panel Header
JIPMB1 4-pin BMC External I2C Header (for an IPMI Card)
JL1 Chassis Intrusion Header
JOH1 Overheat LED Header
JPI C1 Power Supply SMBbus I C Header
2 2
JPWR1 24-pin ATX Power Connector
JPWR2 12V 8-pin Processor Power Connector
JSAS1 Eight SAS 3.0 Ports (X11SSH-CTF only)
JSD1/JSD2 SATA DOM Power Connectors
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
JUIDB1 UID Switch
LAN1/LAN2 LAN (RJ45) Ports
SLOT4 PCH PCI-E 3.0 X2 (IN X4) Slot
SLOT6 CPU PCI-E 3.0 X8 Slot
SP1 Internal Speaker/Buzzer
USB0/1 Back panel Universal Serial Bus (USB) 2.0 Port
USB2/3, USB4/5 Front Accessible USB 2.0 Headers
USB6/7 Back panel USB 3.0 Port
USB8 USB Type A Header
USB9/10 Front Accessible USB 3.0 Header
VGA VGA Port
LED Indicators
LED Description Status
LEDBMC BMC Heartbeat LED Blinking Green: BMC Normal
LEDPWR Onboard Power LED Solid Green: Power On
LEDS1 SAS Activity LED (X11SSH-CTF only) Blinking Green: SAS Active, Red: SAS Error
LE1 UID LED Solid Blue: Unit Identified
LE3 M.2 LED Blinking Green: Active
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
P C
aCkage ontents
: • One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
CPU Support
The X11SSH-CTF/TF motherboard supports an Intel Xeon E3-1200 v5, 6th
Gen Core i3, Pentium, and Celeron series processors in an LGA1151 type
socket.
Memory Support
The X11SSH-CTF/TF motherboard supports up to 64GB of DDR4 ECC UDIMM
memory at a speed of 2133 MHz in four memory slots. Populating these DIMM
slots with a pair of memory modules of the same type and size will result in
interleaved memory, which will improve memory performance.
DIMM Memory Installation
When installing memory modules, the DIMM slots should be populated in the fol-
lowing order: DIMMB2, DIMMA2, then DIMMB1, DIMMA1. Populate the blue sots
first. See the motherboard layout on the left for the location of the DIMM slots.
•
Always use DDR4 DIMM modules of the same type, size, and speed.
•
Mixed DIMM speeds can be installed. However, all DIMMs will run at the
speed of the slowest DIMM.
•
The motherboard will support odd-numbered modules (1 or 3 modules in-
stalled). However, for best memory performance, install DIMM modules in
pairs to activate memory interleaving.
Recommended Population (Balanced)
DIMMA1 DIMMB1 DIMMA2
2GB
2GB 2GB 2GB
4GB
4GB 4GB 4GB
8GB
8GB 8GB 8GB
16GB
16GB 16GB 16GB
Back Panel I/O Connectors
2
5
3 6
1
4
1. COM Port
2. IPMI LAN
3. USB1
4. USB0
5. USB7 (3.0)
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
DIMMB2 Total System Memory
2GB 4GB
2GB 8GB
4GB 8GB
4GB 16GB
8GB 16GB
8GB 32GB
16GB 32GB
16GB 64GB
1
7 8 9
Back panel I/O
6. USB6 (3.0)
7. LAN1
8. LAN2
9. VGA Port