LG LNV7210R series Owner's Manual page 2

Part Names and Functions
a
b
c
h i jk
d
e
f
g
l
Installation
Using the micro SD card Remove the micro SD card
1. Press the back end of the micro SD card to release the lock
You can record your surveillance environment with the micro SD
condition.
card even if the network is disconnected condition.
To insert the micro SD card
1. Remove the Dome Cover.
2. Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the
micro SD card to fix it at the last step.
2. Take the micro SD card out carefully from the camera. It
may cause a malfunction of the micro SD card or the micro
SD card slot if you use the power too much at lock status.
CAUTION:
• If you install the micro SD card on the camera and remove
with the micro SD card condition indicator lights on, you
must unmount the micro SD card by using the [System >
Storage > Device Management > Unmount] menu. The
NOTE:
micro SD card data is compromised or the camera may
not operate normally, if you remove the card without use
• Do not use the power too much when you insert the micro
[Unmount] function.
SD card. The micro SD card may be damaged.
• LG Electronics is not responsible for deleted data caused
• If you insert the micro SD card in the wrong position,
by user mishandling when you insert or remove the micro
the micro SD card may be damaged or it may cause the
SD card.
malfunction of the micro SD Card Slot.
Recommended the micro SD card specification
• Keep the terminal part of the micro SD card in clean. Be
careful the terminal part of the micro SD card not to dusty.
Maker
• As the micro SD card is consumable, the micro SD card end
its days and may be not able to save data if you use it more LG
than over certain times. In this case, replace micro SD card
Sandisk
to buy a new one.
Transcend
*MFL69458110*
NOTE:
Speed of reading and writing more than 10 MB/Sec. (Class 6)
a Dome Cover
b IR Sensor (LNV7210R only)
c IR LED (LNV7210R only)
NOTE:
Do not stare at operating IR LED within hazard distances (1 m).
d micro SD card slot
Insert the micro SD card.
e Jog button
Use this button for control the Zoom / Focus of the camera.
f Video Out Connector
Use this jack for checking the picture with portable monitor when install the camera.
g RESET button
Push the button more than 3 seconds, this would restore the factory default network related
settings.
h AUDIO IN / OUT (Line Level Input/ Output)
i ALARM IN & OUT / ALARM IN & OUT RETURN
Provides physical interface for sensor and Alarm/Relay.
j Power input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be
operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.
k ETHERNET / PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached
RJ-45 connector.
NOTE:
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power
supplies (LPS).
l Camera mounting bracket
You can lock the camera mounting bracket by tighten the screws.
Mounting the camera
Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.
1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.
2. Install the camera mounting bracket to the ceiling.
Capacity Block Size (FAT 32)
Less than
32 kbyte
32 GB
Connection
Precautions Connecting Power Source
• Be sure to switch off the unit before Connect power, using one of the methods
installation and connection. listed below:
• The installation should be made by To use the power adapter
qualified service personnel or system
Connect a DC 12 V power source to the power
installers.
input terminal as shown below.
• Do not expose the power and connection (recommended power adapter is DC 12 V / 1.5
cables to moisture, which may cause A or above)
damage to the unit.
Connecting Network
You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system configuration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.
NOTE:
• When the connecting Alarm and Audio,
tighten the screws as shown above.
• Put your finger between the power
connector and the camera body to pull
out the connector.
PoE Device
(IEEE802.3af )
Broadband
Service
Router
To use the PoE (Power over Ethernet)
Broadband
device
Service
Connect the PoE cable to the LAN port on the
unit. You must use the "IEEE802.3af" standard
PoE device.
3. Connect the cables to the cable jacks of the camera body. 4. Assemble the camera and the housing. Make sure when
you assemble the camera in the right direction. Lock the
camera mounting bracket by tighten the fixing screw.
NOTE:
Push the cap from inside to arrange the cables through the
conduit. (Optional)
NOTE:
• The Photo MOS Relay is rated for 100 mA
at DC 20 V or 100 mA at AC 28 V.
• Grasp both ends of the 3 or 4 pin
connector plug and then sway both side
to pull it out.
PoE Device
(IEEE802.3af )
NOTE:
If the camera doesn't work properly after
Connecting Microphone and
connecting PoE device, please check if the PoE
device supplies enough power. Speaker Device
Connecting Alarm Device
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.
ALARM IN & OUT / ALARM IN & OUT RETURN
(Sensor Input / Relay Output)
Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
AUDIO OUT
AUDIO IN
Alarm (relay)
Device
NOTE:
Keep the microphone away from the speaker
Sensor
to avoid howling.
Device
NOTE:
• Adjust the position of [ALIGN] arrow, to the hole at the
bottom of camera.
Then push and turn in the direction of the [LOCK] arrow.
• Arrange the cables by cable tie after installation.
Camera Adjustment
Adjust the rotation position of the camera.
Fixing Screw
ROTATION
NOTE:
• When you assemble the dome cover, make sure the SD
card PCB position is aligned with the LG logo.
• The camera could be damaged by adjusting Pan, Tilt by
force.
• PAN: 350° / TILT: 75° / ROTATION: 355°
• When you adjust PAN/TILT/ROTATION manually,
be careful your hand is not to hurt by protrusions of other
part.