Carrier 3V VVT 33ZCVVTZC-01 Installation And Start-Up Instructions Manual page 46

Table 19- System Commissioning Maintenance Table
DESCRIPTION VALUE UNITS STATUS FORCE NAME
Commissioning Mode Disable Enable/Disable SCMOD
Auto-Disable Timer 0.0 Min SCTIME
All Zone Dampers to Max Disable Enable/Disable ZD_MAX
All Zone Dampers to Min Disable Enable/Disable ZD_MIN
Position Single Zone Disable Enable/Disable ZD_SING
Zone 1 Damper Position 0 %OPEN ZD_POS0!
Zone 2 Damper Position 0 %OPEN ZD_POS02
Zone 3 Damper Position 0 %OPEN ZD_POS03
Zone 4 Damper Position 0 %OPEN ZD_POS04
Zone 5 Damper Position 0 %OPEN ZD_POS05
Zone 6 Damper Position 0 %OPEN ZD_POS06
Zone 7 Damper Position 0 %OPEN ZD_POS07
Zone 8 Damper Position 0 %OPEN ZD_POS08
Zone 9 Damper Position 0 %OPEN ZD_POS09
Zone 10 Damper Position 0 %OPEN ZD_POS 10
Zone 11 Damper Position 0 %OPEN ZD_POS1 !
Zone 12 Damper Position 0 %OPEN ZD_POS 12
Zone 13 Damper Position 0 %OPEN ZD_POS13
Zone 14 Damper Position 0 %OPEN ZD_POS14
Zone 15 Damper Position 0 %OPEN ZD_POS15
Zone 16 Damper Position 0 %OPEN ZD_POS 16
Zone 17 Damper Position 0 %OPEN ZD_POS 17
Zone 18 Damper Position 0 %OPEN ZD_POS 18
Zone 19 Damper Position 0 %OPEN ZD_POS 19
Zone 20 Damper Position 0 %OPEN ZD_POS20
Zone 21 Damper Position 0 %OPEN ZD_POS21
Zone 22 Damper Position 0 %OPEN ZD_POS22
Zone 23 Damper Position 0 %OPEN ZD_POS23
Zone 24 Damper Position 0 %OPEN ZD_POS24
Zone 25 Damper Position 0 %OPEN ZD_POS25
Zone 26 Damper Position 0 %OPEN ZD_POS26
Zone 27 Damper Position 0 %OPEN ZD_POS27
Zone 28 Damper Position 0 %OPEN ZD_POS28
Zone 29 Damper Position 0 %OPEN ZD_POS29
Zone 30 Damper Position 0 %OPEN ZD_POS30
Zone 31 Damper Position 0 %OPEN ZD_POS31
Zone 32 Damper Position 0 %OPEN ZD_POS32
Bypass Damper Position 0 %OPEN BDP
Bypass Pressure Sensor 0.00 in H20 BPSENS
Bypass Pressure Setpoint 0.00 in H20 BPSETP
AUTO DISABLE TIMER -- This vmiable displays the num-
ber of minutes remaining before the system commissioning
mode will be automatictflly disabled. System commissioning
mode is automatic_dly disabled after one hour of no activity in
this table. The Auto Disable Timer is reset each time a v;due is
changed in this table.
Auto Disable
Timer: Display Range 0 to 60 min
Network Access None
ALL ZONE DAMPERS TO MAX -- This variable displays
whether the Linkage Coordinator zone controller has been
directed to set all of its linked zone controllers to their config-
ured Cool Maximum Positions (Dmnper Service Configuration
Table). If this decision is forced to Erlable, the Linkage Coordi-
nator zone controller will set all system zone dampers to their
configured Cool Maximum Positions and display the values in
Zone (1-32) Damper Position variables. At this time if any of
the Zone (1-32) Damper Position variables are forced, the new
position will be written to the zone's Cool Maximum Position
and Heat Maximum Position configuration values and the zone
will be repositioned to this new maximum position.
NOTE: If this zone controller is not the Linkage Coordinator,
enabling this variable will have no effect.
All Zone
Dampers to Max: Display Range Enable/Disable
NetwoN Access Read/Write
ALL ZONE DAMPERS TO MIN -- This vmiable displays
whether the Linkage Coordinator zone controller has been
directed to set all of its linked zone controllers to their config-
ured Cool Minimum Positions (Damper Service Configuration
Table). If this decision is forced to Erlable, the Linkage Coordi-
nator zone controller will set all system zone dampers to their
configured Cool Minimum Positions and display the values in
Zone (1-32) Damper Position vmiables. At this time if tiny of
the Zone (1-32) Damper Position variables are forced, the new
position will be written to the zone's Cool Minimum Position
and Heat Minimum Position configuration values and the zone
will be repositioned to tiffs new minimum position.
NOTE: If this zone controller is not the Linkage Coordinator,
enabling this variable will have no effect.
All Zone
Dmnpers to Min: Display Range Enable/Disable
NetwoN Access Read/Write
46