Carrier 3V VVT 33ZCVVTZC-01 Installation And Start-Up Instructions Manual page 45

Table 18 --Time Schedule Maintenance Table
DESCRIPTION VALUE UNITS NAME
Mode 1 MODE
Current Occupied Period 2 PERIOD
Override in Progress No OVERLAST
Override Duration 0 min OVERDURA
Occupied Start Time 08:00 OCCSTART
Unoccupied Start Time 18:00 UNSTART
Next Occupied Day Thu NXTOCCD
Next Occupied Time 00:00 NXTOCCT
Next Unoccupied Day Wed NXTUNOD
Next Unoccupied Time 18:00 NXTUNOT
Last Unoccupied Day PRVUNOD
Last Unoccupied Time 00:00 PRVUNOT
UNOCCUPIED START TIME -- This variable displays the
time that the current occupied mode will end (the beginning of
the next unoccupied mode).
Unoccupied Start
Time: Display Range 00:00 to 24:00
Network Access None
NEXT OCCUPIED DAY- This vadable displays the &ty
when the next occupied period is scheduled to begin. This
point is read in conjunction with the next occupied time to
allow the user to know the next time and day when the next
occupied period will occm:
NOTE: If the current mode is occupied, this point makes refer-
ence to the next occupied pedod and, in most cases, may not
be the stone as the cunent occupied start time.
Next Occupied
Day: Display Range MON, TUE, WED,
THU, FRI, SAT. SUN
Network Access None
NEXT OCCUPIED TIME -- This variable displays the time
of day when the next occupied period will occm: This point is
read in conjunction with the next occupied &ty to allow the
user to know the next time and day when the zone will become
occupied.
NOTE: If the current mode is occupied, this point makes
reference to the next occupied period and, in most cases,
may not be the same as the current occupied start time.
Next Occupied
Time: Display Range 00:00 to 24:00
Network Access None
NEXT UNOCCUPIED DAY-- This variable displays the
day when the next unoccupied period is scheduled to begin.
This point is read in conjunction with the next unoccupied time
to allow the user to know the next time and day when the zone
will become unoccupied.
NOTE: If the current mode is unoccupied, this point makes
reference to the next unoccupied period and, in most cases,
may not be the same as the current unoccupied start time.
Next Unoccupied
Day: Display Range MON, TUE, WED,
THU, FRI, SAT. SUN
Network Access None
NEXT UNOCCUPIED TIME -- This variable displays the
time of day when the next unoccupied period is scheduled
to begin. This point is read in conjunction with the next
unoccupied day to allow the user to know the next time and
&ty when the zone will become unoccupied.
NOTE: If the current mode is unoccupied, this point makes
reference to the next unoccupied period and, in most cases,
may not be the same as the current unoccupied start time.
Next Unoccupied
Time: Display Range 00:00 to 24:00
Network Access None
LAST UNOCCUPIED DAY-- This vmiable displays the
last day when the zone changed from occupied to unoccupied
mode. This point is read in conjunction with the last unoccu-
pied time to allow file user to know the last time and day
when the zone became unoccupied.
Last Unoccupied
Day: Display Range MON, TUE, WED,
THU, FRI, SAT. SUN
Network Access None
LAST UNOCCUPIED TIME -- This variable displays the
last time of &ly when the zone changed from occupied to unoc-
cupied mode. This point is read in conjunction with the last
unoccupied day to _dlow the user to know the last time and day
when a zone becmne unoccupied.
Last Unoccupied
Time: Display Range 00:00 to 24:00
Network Access None
System Commissioning Maintenance Table --
The System Colnmissioning Maintenance _tble (SYSTCOMM)
displays and perlnits the setting of 'all &tlnpel_ in the linked sys-
tem from the Linkage Coordinator zone controllel: The bypass
controller &tmper position, system plessme and pressure set
point me also displayed and the plessure set point may be _dteled
directly from fllis table. See Table 19.
COMMISSIONING MODE -- This vmiable is used to put
file master zone controller into the commissioning mode. Force
tiffs point to enable. The Linkage Coordinator zone controller
will be ready to accept a command to perform the tests and
functions on this screen. The Linkage Coordinator zone con-
troller will go into ZONE_BAL mode.
NOTE: If this zone controller is not the Linkage Coordinatol:
enabling this variable will have no effect.
Commissioning
Mode: Display Range Disable/Enable
Default Value Disable
Network Access Read/Write
45