Table of Contents
Advertisement
IMPORTANT NOTE TO THE
OWNER REGARDING
PRODUCT WARRANTY
Your warranty certificate is supplied as a separate document with
the unit installed by your contractor. Read the limited warranty
certificate carefully to determine what is and is not covered. Keep
the warranty certificate in a safe place. If you are unable to locate
the warranty certificate, please contact your installing contractor,
or contact customer service at 1-866-944-7575 to obtain a copy.
To receive the 10-Year Parts Limited Warranty, online registration
must be completed within 60 days of installation. Online
registration is not required in California or Quebec.
Full warranty details and instructions are available at
www.whirlpoolhvac.com.
To register your unit, go to www.whirlpoolhvac.com. Click on the
manufacturer's Comfort Commitment
the bottom center of the home page. Next, click on the Click
Here to Register Your Product link located at the top center of the
page, and complete the forms in the manner indicated.
SHIPPING INSPECTION
Upon receiving the unit, inspect it for damage from shipment.
Claims for damage, either shipping or concealed, should be filed
immediately with the shipping company. Check the unit model
number, specifications, electrical characteristics and accessories
to determine if they are correct. In the event an incorrect unit is
shipped, it must be returned to the supplier and must not be
installed. The manufacturer assumes no responsibility for
installation of incorrectly shipped units.
REPLACEMENT PARTS
When reporting shortages or damages, or ordering repair parts,
give the complete product model and serial numbers as stamped
on the product. Replacement parts for this product are available
through your contractor or local distributor. For the location of
your nearest distributor, consult the white business pages, the
yellow page section of the local telephone book or contact:
Tradewinds Distributing Company, LLC
14610 Breakers Drive
Jacksonville, Florida 32258
1-866-944-7575
If you are replacing an air handler, the system must be
manufacturer-approved and Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) matched.
NOTE: Installation of unmatched systems is strongly
discouraged.
CODES AND REGULATIONS
The WPC/WPH M-series air conditioners and heat pumps are
designed for outdoor use only. WPH M-Series is available in
cooling capacities of 2, 2¹⁄₂, 3, 3¹⁄₂, 4 and 5 nominal tons of
cooling. WPC M-Series is available in cooling capacities of 3,
4 and 5 nominal tons of cooling. Optional field-installed heat kits
are available in 5, 8, 10, 15 and 20 kW. The units can be easily
installed in manufactured or modular homes with existing high-
static ductwork. The units can also be easily converted to
accommodate a plenum for normal or low-static applications.
TM
Warranty link located at
The WPC/WPH M-series are self-contained packaged units so
the only connections needed for installation are the supply and
return ducts, the line and low voltage wiring and drain
connection. The units are ETL listed and AHRI certified.
The information on the rating plate is in compliance with the FTC
and DOE rating for single-phase units. The efficiency ratings of
these units are a product of thermal efficiency determined under
continuous operating conditions independent of any installed
system.
EPA Regulations
IMPORTANT: The United States environmental protection
agency (EPA) has issued various regulations regarding the
introduction and disposal of refrigerants in this unit. Failure to
follow these regulations may harm the environment and can lead
to the imposition of substantial fines. Because regulations may
vary due to passage of new laws, we suggest a certified
technician perform any work done on this unit. Should you have
any questions, please contact the local office of the EPA.
National Codes
This product is designed and manufactured to permit installation
in accordance with National Codes. It is the installer's
responsibility to install the product in accordance with National
Codes and/or prevailing local codes and regulations.
MAJOR COMPONENTS
The unit includes a hermetically sealed refrigerating system
(consisting of a compressor, condenser coil, evaporator coil with
flowrator), an indoor blower, a condenser fan and all necessary
internal electrical wiring. The heat pump also includes a reversing
valve, solenoid, defrost thermostat and control and loss of charge
protection. The system is factory-evacuated, charged and
performance tested. Refrigerant amount and type are indicated
on rating plate.
PREINSTALLATION CHECKS
Before attempting any installation, the following points should be
considered:
Structural strength of supporting members
Clearances and provision for servicing
Power supply and wiring
Air duct connections
Drain facilities and connections
Location may be on any 4 sides of a home, manufactured or
modular, to minimize noise.
Clearances and Accessibility
The unit is designed to be located outside the building with
unobstructed condenser air inlet and discharge. Additionally, the
unit must be situated to permit access for service and
installation. Condenser air enters from 3 sides. Air discharges
upward from the top of the unit. Refrigerant gauge connections
are made on the right side of the unit as you face the compressor
compartment. Electrical connections can be made either on the
right, bottom or duct panel side of the unit. The best and most
common application is for the unit to be located 10" (25.4 cm)
from the wall (4" [10.2 cm]) minimum) with the connection side
facing the wall. Close to the wall application minimizes exposed
wiring.
3
Advertisement
Table of Contents
Troubleshooting
