Model Number Description; Commercial Self-Contained Signature; Series - Trane IntelliPak SCWF 20 Installation, Operation And Maintenance Manual

Model Number Description

Commercial Self-Contained Signature Series
Digit 1 — Unit Model
S = Self-Contained
Digit 2 — Unit Type
C = Commercial
I = Industrial
Digit 3 — Condenser Medium
W = Water-cooled
R = Air-cooled
Digit 4 — Development Sequence
F = Signature Series
Digit 5— Refrigerant Circuit
Configuration
U = Standard Capacity
V = High Capacity
Digit 6, 7 — Unit Nominal Capacity
20 = 20 Tons (water only)
22 = 22 Tons (water only)
25 = 25 Tons (water or air)
29 = 29 Tone (water or air)
30 = 30 Tons (air only)
32 = 32 Tons (water only)
35 = 35 Tons (water or air)
38 = 38 Tons (water only)
40 = 40 Tons (air only)
42 = 42 Tons (water only)
46 = 46 Tons (water only)
50 = 50 Tons (air only)
52 = 52 Tons (water only)
58 = 58 Tons (water only)
60 = 60 Tons (air only)
65 = 65 Tons (water only)
72 = 72 Tons (water only)
80 = 80 Tons (water only)
90 = 90 Tons (water only)
C0 = 100 Tons (water only)
C1 = 110 Tons (water only)
Digit 8 — Unit Voltage
6 = 200 volt/60 hz/3 ph
4 = 460 volt/60 hz/3 ph
5 = 575 volt/60 hz/3 ph
Digit 9 — Air Volume/Temp Control
2 = VFD and supply air temp ctrl
3 = VFD w/ bypass and supply air temp ctrl
4 = Constant volume, zone temp cool only
5 = Constant volume, w/ zone temp heat/
cool
6 = Constant volume and supply air temp ctrl
SCXF-SVX01Q-EN
Digit 10, 11 — Design Sequence
** = Factory Assigned
Digit 12 — Unit Construction
A = Vertical discharge
B = Vertical discharge with double wall
Digit 13— Flexible Horizontal
Discharge Plenum Type
B = STD plenum w/ factory-cut holes
C = Low plenum w/ factory-cut holes
E = Std plenum w/ field-cut holes
F = Low plenum w/ field-cut holes
H = STD plenum double wall w/ field-cut
holes
J = Low plenum double wall w/ field-cut holes
K = Extended height plenum w/factory-cut
holes, ship separate
L = STD plenum w/factory-cut holes, ship
separate
M = Low plenum w/factory-cut holes, ship
separate
N = Extended height plenum w/field-cut
holes, ship separate
P = STD plenum w/field-cut holes, ship
separate
R = Low plenum w/field-cut holes, ship
separate
T = Extended height double-wall plenum w/
field-cut holes, ship separate
U = STD double-wall plenum w/field-cut
holes, ship separate
V = Low double-wall plenum w/field-cut
holes, ship separate
W = STD double-wall (perf) plenum w/field-
cut holes (90 to110 ton only)
X = Low double-wall (perf) plenum w/field-
cut holes (90 to 110 ton only)
Y = Extended height double-wall (perf)
plenum w/field-cut holes, ship separate (90
to 110 ton only)
0 = None
Digit 14— Motor Type
2 = ODP motor
4 = TEFC motor
Digit 15, 16 — Motor HP
05 = 5 hp
07 = 7.5 hp
10 = 10 hp
15 = 15 hp
20 = 20 hp
25 = 25 hp
30 = 30 hp
40 = 40 hp
50 = 50 hp (460V, 575V only)
60 = 60 hp (90 to 110 ton only)
Digit 17, 18, 19 – Fan RPM
040 = 400 rpm
045 = 450 rpm
050 = 500 rpm
052 = 525 rpm
055 = 550 rpm
057 = 575 rpm
060 = 600 rpm
065 = 650 rpm
070 = 700 rpm
075 = 750 rpm
080 = 800 rpm
085 = 850 rpm
090 = 900 rpm
095 = 950 rpm
100 = 1000rpm
105 = 1050 rpm
110 = 1100 rpm
115 = 1150 rpm
120 = 1200 rpm
125 = 1250 rpm
130 = 1300 rpm
135 = 1350 rpm
Digit 20 — Unit Isolators
A = Steam coil
B = Hot water coil
C = Electric heat, 1 stage
D = Electric heat, 2 stage
F = Hydronic heat ctrl interface
G = Electric heat ctrl interface
K = Steam coil ship separate, LH
L= Hot water coil ship separate, LH
T = Hot water coil, high capacity, LH
U = Hot water coil, high capacity, LH, ship
separate
0 = None
Digit 21 — Unit Isolators
A = Isopads
B = Spring isolators
0 = None
Digit 22— Unit Finish
1 = Paint - Slate Gray
Digit 23— Supply Fan Options
0 = Standard fan
1 = Low CFM fan
Digit 24— Unit Connection
1 = Disconnect switch
2 = Terminal block
3 = Dual point power (2 blocks)
11