Advertisement
2 Operation
For first time users, please follow the steps below to complete the
pre-installation.
2.1 Install the SIM card
Unscrew the cover of device. Insert SIM card with the copper contacts
face-down and the notch on the SIM card at the left side of the SIM slot.
Note: Make sure to disable the SIM PIN entry function on the SIM card
before inserting your SIM card
After installing the SIM card,
please screw the back cover..
M1.7- #00
3.2 Connecting ignition detection line on Vehicle
Analog Input
Input Negative
(Blue)
(Yellow)
SOS
Main Power
(Green)
(Red)
Ground
Ground
(Black)
(Black)
Out Input
Ignition Detection Input
(White)
(Orange)
Off
ACC
Lock
Ignition On
Connect the orange wire from the cable to ACC
position of vehicle. Connect the black wire to ground.
2.2 Connect the Main Cable
Please pay attention to hand-tighten the fool-proof connector of the cable
with tracker.
2.3 Connect the Main Power
Analog Input
(Blue)
SOS
(Green)
Ground
Ground
(Black)
(Black)
Out Input
Ignition Detection Input
(White)
(Orange)
Connect the red wire from the cable to a power source of 9V~36 V.
Connect the black wire to ground.
08
3.3 Connecting Relay
Car Battery
+
To Car Battery+
Cut off Ignition Power Connect with Really
Relay Yellow Cable
Relay
Relay Black Cable
85
Red
30
Tracker
87 87a
Relay Blue Cable
86
White
(Current limit 300mA)
Relay Yellow Cable
Connect the white wire from device's cable to the yellow wire of relay.
For the other connections, please refer to the diagram above.
3.4 Installation reminder
WARNING:
In a confined space of the car, there is a big different temperature
between inside and outside of the car. In addition, it is also considerable
temperature difference between tracker's interior and exterior.
Therefore, if you put a tracker in the car, please make sure to place it
with good ventilation.
12
2.4 Turn on Tracker
After connecting the power, please press the
reset button to turn on the device.
2.5 Fix the device
You could fix the device
with the Velcro tape as the
picture above.
Input Negative
(Yellow)
Main Power
(Red)
You could tear down the cover of double side
tape and stick to the installation position.
There is a magnet behind the double side tape.
You could install the device to a metal surface.
The magnet on the device would attract the
metal surface.
09
For Vehicle:
The device could be placed or installed on the marked position as the
pictures below.
Glove compartment
Off
Lock
ACC
lgnition(ON)
Under dashboard
(OBD2 connector)
If you'd like to install to the OBDII connector of vehicles, please connect
device with the OBDII power cable firstly, then you could connect the
OBDII power cable to the OBDII connector of vehicle as the picture
below.
13
3 Installation
3.1 Installing the Emergency button
There is a line of cable for connecting a push button for emergency help.
Analog Input
(Blue)
SOS
(Green)
Ground
(Black)
Out Input
(White)
One end of the button must be connected to the SOS line and the other
end must be connected to the ground line.
SOS line
(red wire)
Ground line
(Black wire)
10
For Motorcycle:
For motorcycle rider, the device could be installed at the marked position
as the picture as below.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
Back of front seat
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and receiver.
●
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●
Consult the dealer or an experienced radio/ TV technician for help.
●
Notice:
Any changes or modifications not expressly approved by the party responsible for compliance could void
your authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located of operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.
減少電磁波影響，請妥適使用
內建固定式電池：「消費者不可自行拆卸內建電池，如要拆卸需請專業人士/維修廠商拆卸」
14
13
14
N3PM2GTR388000
N3PM2GTR388001
Input Negative
(Yellow)
Main Power
(Red)
Ground
(Black)
Ignition Detection Input
(Orange)
11
15
15
Advertisement
