Instructions In Mode1 And Mode2 - Roland PNC-900 Camm-1 User Manual

Instruction Format
OA OA;
OC OC;
OE OE;
OF OF;
OH OH;
OI OI;
OO OO;
OP OP;
OS OS;
OW OW;
PA PA x1, y1(...,xn, yn);
PA;
PD PD x1, y1(...,xn, yn);
PD;
PR PR 1, y1(... xn, yn);
PR;
PT PT d;
PT;
PU PU x1, y1(...,xn, yn);
PU;
RA RA x, y;
RR RR x, y;
SA SA;
SC SC Xmin, Xmax, Ymin,
Ymax;
SC;
SI SI w, h;
SI;
SL SL tanØ;
SL;
SM SM s;
SM;
SR SR w, h;
SR;
SS SS;
TL TL lp(,lm);
TL;
UC UC (c,) x, y,(c,)
,...., xn, yn;
UC;
VS VS v;
VS;
WG WG r, Ø1, Øc(,Ød);
XT XT;
YT YT;

• Instructions in mode1 and mode2

Instruction Format
!NR !NR [terminator]
!PG !PG n [terminator]
!ST !ST n [terminator]
Meaning of Parameter [Parameter Range (Default)]
None
None
None
None
When the PNC-900 receives an OF instruction from the computer,
"40,40 [TERM]" is output.
None
None
When the PNC-900 receives an OI instruction from the computer,
"900 [TERM]" is output.
None
When the PNC-900 receives an OO instruction from the computer,
"0,0,0,0,1,0,0,0 [TERM]" is output. The "1" in this output indicates that
circle and arc commands have been loaded
None
None
None
xn, yn: Absolute XY coordinates [*1]
xn, yn: XY coordinates [*1]
xn, yn: Relative XY coordinates [*1]
d: Pen thickness (mm) [0—5 (0.3)]
xn, yn: XY coordinates [*1]
x, y: Absolute XY coordinates of opposite angle of rectangle [*1]
x, y: Relative XY coordinates of opposite angle of rectangle [*1]
None
Xmin, Ymin: User XY coordinates of P1 [*1]
Xmax, Ymax: User XY coordinates of P2 [*1]
w: Character width (cm.) [-128 — +127.99999 (3.8)]
h: Character height (cm.) [-128 — +127.99999 (5)]
tanØ: Character slant [*1 (0)]
s: Character or symbol [*4 (Default: Clears symbol mode)]
w: Character width (%) [*1 (3.8 )]
h: Character height (%) [*1 (5 )]
None
lp: Tick length in positive direction [*2 (0.5%)]
lm: Tick length in negative direction [*2 (0.5%)]
c: Tool control value [-(67108863) — -99, +99 — +(67108863)]
xn: Units of movement in X-axis direction [-99< xn<+99]
yn: Units of movement in Y-axis direction [-99< yn<+99]
v: Tool speed (cm/sec.) [1 — 20 ]
r : Radius [*1] Ø1 : Start angle [*3]
Øc : Center angle [*3] Ød : Chord tolerance [*3 (5 )]
None
None
Meaning of Parameter [Parameter Range (Default)]
None
n: [-1600 — +1600 mm]
n: [0, 1]
Explanation
Output Actual Point
Output Commanded Position
Output Error
Output Factor
Output Hard-Clip Limits
Output Identification
Output Option Parameter
Output P1 & P2
Output Status
Output Window
Cut Absolute
Tool Down
Cut Relative
Pen Thickness
Tool Up
Shade Rectangle Absolute
Shade Rectangle Relative
Select Alternate Set
Scaling
Absolute Character Size
Character Slant
Symbol Mode
Relative Character Size
Select Standard Set
Thick Length
User Defined Character
Velocity Select
Shade Wedge
X-Tick
Y-Tick
Explanation
Not Ready
Page Feed
Select Tool
19