Korenix JetCon 3401G Quick Installation Manual

A Beijer Electronics Group Company
JetCon 3401G Industrial Gigabit Ethernet Media Converter
Quick Installation Guide V1.2
Overview
e JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T,
802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit ber
conversion using store and forward technology. e JetCon 3401G adopts rugged metal case
o
design to operate in harsh environments (-25~70 C); It also provides IP-31 standard
protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can
be enabled/ disabled by dip switch. e ber port supports SFP socket for several of SFP
transceiver to achieve di erent link distance.
JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the
6-pin removable terminal block.
Package Check List
A Beijer Electronics Group Company
JetCon 3401G Industrial Gigabit Ethernet Media Converter
Quick Installation Guide V1.2
Overview
 JetCon 3401G
e JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T,
802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit ber
conversion using store and forward technology.
design to operate in harsh environments (-25~70oC); It also provides IP-31 standard
 Quick Installation Guide protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can
be enabled/ disabled by dip switch. e ber port supports SFP socket for several of SFP
transceiver to achieve di erent link distance.
JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the
 CD User Manual 6-pin removable terminal block.
Package Check List
 JetCon 3401G
 Quick Installation Guide
 CD User Manual
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 3401G on the DIN rail.
For information about the DIN Rail installation, please refer to user's manual.
Wiring the Power Inputs
1. Insert the positive and negative wires into
the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent
the DC wires from being loosened. See Figure-1
Notes: e recommended working voltage is DC24V (DC12~ 48V)
Wiring the Relay Output
Maximum 1A current / DC 24V
e relay output alarm contacts are in the middle of
the terminal block connector as shown in gure-3.
By inserting the wires and settings the DIP switch of PW1P Alm 1@ DC24V
+
the respective alarm function to "ON", relay output
alarm will detect port or power fault, and form a
short circuit. e alarm relay output is "Normal Open". See, Figure -2. For more information,
please refer to the chapter 2-4 and 2-5 of user's manual for more detail information.
Wiring the Earth Ground
In an industrial environment, there might be
devices that generate electromagnetic noise, such
as AC motors, electric welding machine, or a
power generator. ese devices will generate
electric noise or surges that might disturb
communications.
To prevent those noises, the device should be well earthed. In the Figure- 3 shows how
to make connection.
Connecting to Network
1. Connecting the Ethernet Ports: Connect one end of an Ethernet cable into the UTP port
of JetCon 3401G, while the other end is connected to the attached networking device.
UTP ports support auto MDI/MDIX function.
and blinking for 100Mbps link; the LNK/ACT LED will turn on for link up and blinking
for packet transmits and receives.
2. Install Gigabit SFP transceiver and make the connection: Connect the ber port on
your JetCon 3401G to another Gigabit Fiber Ethernet device, by following the gure below.
Industrial Networking & Computing
Wrong connection will cause the ber port not working properly.
Software and Documentation
e JetCon 3401G adopts rugged metal case
e SFP Fiber port supports 2 LEDs for link/activity and full duplex/collision; once the
A Beijer Electronics Group Company
gigabit ber port is link up, the link LED will be trigger to "ON".
JetCon 3401G Industrial Gigabit Ethernet Media Converter A Beijer Electronics Group Company
Overview Quick Installation Guide V1.2 Industrial Networking & Computing
e JetCon 3401G Industrial Gigabit Ethernet Converter, conforming IEEE 802.3 10Base-T, 802.3u 100Base-TX and 1000Base-T/SX/LX standard, supports RJ-45 copper to Gigabit ber Software and Documentation
design to operate in harsh environments (-25~70oC); It also provides IP-31 standard conversion using store and forward technology. e JetCon 3401G adopts rugged metal case
also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can protection. It features Link Loss Forwarding to raise an alarm when a remote fault occurs and
be enabled/ disabled by dip switch. transceiver to achieve di erent link distance. JetCon 3401G is recommended to be powered by DC 24V with 12~48V range from the 6-pin e ber port supports SFP socket for several of SFP A Beijer Electronics Group Company
Package Check List removable terminal block.
 JetCon 3401G  Quick Installation Guide
CD User Manual 
ATTENTION
is is a Class 1 Laser/LED product.
！ Don't look into the Laser/LED Beam.
DIP Switch Settings for Alarm Relay Output and Link
Loss Forwarding
Pin No. # Status
Figure-1
ON
# 1
Port Event Alarm
Off
ON
#2
Power Event Alarm
Off
#3 ON
Figure-2
LLF
Alarm
System
(Link Loss Forwarding)
Off
Extra Power
System
W2
+
Power Event Alm
Port Event Alm LLF
ON: Enable
Figure-3
Earth Ground
Screw
PW1P Alm 1@ DC24V W2
+ +
Power Event Alm
Port Event Alm LLF
ON: Enable
Earth Ground
Warning: Do not connect to AC line-Natura l
e
e Speed LED will turn on for 1000M link
Description
To enable port link down alarm at this port.
To disable port link down alarm at this port.
To enable power failure alarm.
To disable power failure alarm.
To enable Link Loss Forwarding function at both of fiber and
copper port. Once either one of copper or fiber port is
disconnected, the JetCon 3401G will turn-off the other port to
alert the end of attached device forcibly.
Note: Once the LLF is active and the cable event is recovered,
the LLF DIP-switch must be re-triggered to arouse this function.
To disable Link Loss Forwarding function.
Support
5 Years Warranty
Each of Korenix's product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional sta s are
ready to solve your problems at any time Korenix global service center's e-mail is
KoreCARE@korenix.com.
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm