Korenix JetCon 2301 Quick Installation Manual

A Beijer Electronics Group Company
JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.1
Overview
JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of
forwarding modes – Store and Forward, Modi ed Cut-through, Pure Converter and
Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with
IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh environments
with severe electromagnetic interference and -25~70°C (JetCon 2301) or -40~75°C (JetCon
2301-w). It features Link Loss Forwarding to forward link status changes for alerting remote
or central management systems when a remote fault occurs. It also adopts one relay output to
alarm users if a port link fails or if the power fails. Alarms can be enabled/ disabled by dip
switch. JetCon 2301 has redundant power inputs with wide range DC10~60V through the
6-pin removable terminal block. e ber port supports Single-mode or Multi-mode for
providing up to 30KM extended distance transmission.
Package Check List
 JetCon 2301 Industrial Media Converter
 Quick Installation Guide
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 2301 on
the DIN rail. For information about the DIN Rail installation, please
refer to user's manual.
Grounding JetCon 2301
ere is one grounding screw on the bottom side
of JetCon 2301. Connect the frame grounding of
JetCon 2301 to the grounding surface to ensure
safety and prevent noise for communication
interference.
Chassis connects
to the Earth Ground
Wiring the Power Inputs
1. Insert the positive and negative
wires into the V+ and V- contact on
the terminal block connector.
2. Tighten the wire-clamp screws to
prevent the power wires from being
loosened.
Accept 24AWG wire. JetCon 2301
Note: e recommended working voltage
provides auto-polarity reverse
is DC 24V (Input range: DC10~ 60 V)
Wiring the Relay Output
e relay output contacts are in the middle of the
terminal block connector as shown in
below. By inserting the wires and by setting the
DIP switch of the respective alarm function to
"ON", relay output alarm will detect port or
power fault, and form a short circuit.
relay output is "Normal Open". For detailed
information, please refer to chapter 2-5 of the
User's Manual.
Note: e relay contact supports only 1A current, DC 24V. It is not recommended
to apply higher voltage and current higher than this speci cation.
Connecting to Network
1. Connecting the Ethernet Port: Connect one end of an Ethernet cable into the UTP port
of JetCon 2301, while the other end is connected to the attached networking device. UTP
port supports auto MDI/MDIX function.
ashing to indicate RJ-45 port links and the packets received and transmitted from RJ-45.
2. Connecting the Fiber Port: Connect the ber port of your JetCon 2301 to another Fiber
A Beijer Electronics Group Company
JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter
Quick Installation Guide V1.1
Overview
JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of
forwarding modes – Store and Forward, Modi ed Cut-through, Pure Converter and
Ethernet device, by following the gure below. Wrong connection or wrong ber cable type
Converter with auto-change modes. e JetCon 2301 adopts rugged aluminum case with
IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh
environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or
-40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes
for alerting remote or central management systems when a remote fault occurs. It also
adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be
will cause the ber port not working properly.
enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range
DC10~60V through the 6-pin removable terminal block. e ber port supports
Single-mode or Multi-mode for providing up to 30KM extended distance transmission.
Package Check List
 JetCon 2301 Industrial Media Converter JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter Overview Quick Installation Guide V1.1 A Beijer Electronics Group Company
Converter with auto-change modes. JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of forwarding modes – Store and Forward, Modi ed Cut-through, Pure Converter and e JetCon 2301 adopts rugged aluminum case with
 Quick Installation Guide environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh -40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes
enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range for alerting remote or central management systems when a remote fault occurs. It also adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be
Single-mode or Multi-mode for providing up to 30KM extended distance transmission. DC10~60V through the 6-pin removable terminal block. Package Check List e ber port supports
  Quick Installation Guide JetCon 2301 Industrial Media Converter
ATTENTION
is is a Class 1 Laser/LED product.
！ Don't look into the Laser/LED Beam.
3. For di erent link distances, the JetCon 2301 provides JetCon 2301-m" for multi-mode
ber and "JetCon 2301-s" for single-mode ber.
Alm
4. e table below illustrates ber transceiver speci cation.
PW1 PW2
TP SPD Mode Alm Flw Con.
LLF
Modul Fiber (um) Connecter
JetCon
Multi-Mode
SC
2301-m
50~62.5/125
JetCon Single-Mode
SC
2301-s 8-10/125
xPwr(Min):Minimum Launch Power
RxPwr(Min):Maximum Receive Sensitivity
Link Budget=Minimum Launch Power –Maximum Receive Sensitivity
Note: To ensure your ber converter can transmit/receive data between the 2 nodes, the
attenuation of the optical ber cable should be smaller than the ber converter's Link Budget.
Alarm
System
gure
Maximum 1A current / DC 24V
Extra Power
System
Alm
PW1 PW2
TP SPD Mode Alm Flw Con.
LLF
e alarm
e LNK / ACT LED will turn on and start
RX RX
TX TX
Cable Wiring(SC to SC)
TX A RX B
RX A TX B
TXPwr TxPwr RxPwr RxPwr
Wavelength(um) LinkBudg(dBm) Distance(km)
(Min) (Max) (Min) (Max )
1310nm -20dB m -14dBm -31dBm 0dB m 11dB m 2K M
1310nm -15dB m -8dBm -34dBm 8dBm 19dB m 30km
TxPwr(Max):Maximum Launch Power
RxPwr(Max):Minimum Receive Sensitivity
DIP Switch Setting
Pin No. # Status Description
On Enable Link Loss Forwarding function.
DIP 1
Off Disable Link Loss Forwarding function (Default)
On Set TX port in 10 Mbps Half Duplex mode
DIP 2
Off Set TX port in Auto-Negotiation mode (Default)
On Enable power alarm
DIP 5
Off Disable power alarm (default)
On Enable port alarm
DIP 6
Off Disable port alarm (default)
On Disable Flow control
DIP 7
Off Enable Flow control (default)
DIP 3 DIP 4
Store and Forward forwarding mode (default mode)
Off Off
Pure Converter forwarding mode
Off On
Modify Cut-Through forwarding mode
On Off
Converter mode with Auto-Change forwarding mode
On On
Note: After adjusting the DIP-switch, please reboot the unit to activate
the new settings.
Support
5 Years Warranty
Each of Korenix's product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
Support is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional sta s are
ready to solve your problems at any time Korenix global service center's e-mail is
KoreCARE@korenix.com.
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
1 2 3 4 5 6 7
1 2 3 4 5 6 7