Table of Contents
Advertisement
Quick Links
Installation Manual
RADAR SENSOR
DRS4DL+
Model
(Product Name: RADOME RADAR SENSOR)
SAFETY INFORMATION.................................................................................................. i
SYSTEM CONFIGURATION .......................................................................................... iv
EQUIPMENT LISTS......................................................................................................... v
1. INSTALLATION.......................................................................................................... 1
1.1 Installation Considerations....................................................................................................1
1.2 Installation of the Radar Sensor............................................................................................2
2. INITIAL SETUP........................................................................................................... 7
2.1 Connections ..........................................................................................................................7
2.2 Initial Setup for NavNet TZtouch (Model: TZT9/TZT14/TZTBB) ...........................................7
2.3 Initial Setup for NavNet TZtouch2 (Model: TZTL12F/TZTL15F) .........................................10
2.4 Check Points After Installation ............................................................................................12
3. MAINTENANCE, TROUBLE- SHOOTING............................................................... 14
3.1 Maintenance .......................................................................................................................14
3.2 Replacement of Fuse..........................................................................................................15
3.3 Troubleshooting ..................................................................................................................15
3.4 Replacement of Magnetron.................................................................................................15
APPENDIX 1 RADIO REGULATORY INFORMATION ............................................AP-1
SPECIFICATIONS ..................................................................................................... SP-1
PACKING LIST ............................................................................................................ A-1
OUTLINE DRAWING ................................................................................................... D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Advertisement
Table of Contents
Related Manuals for Furuno DRS4DL+
Summary of Contents for Furuno DRS4DL+
-
Page 1: Table Of Contents
3.4 Replacement of Magnetron....................15 APPENDIX 1 RADIO REGULATORY INFORMATION ..........AP-1 SPECIFICATIONS ..................... SP-1 PACKING LIST ......................A-1 OUTLINE DRAWING ....................D-1 INTERCONNECTION DIAGRAM ................S-1 www.furuno.com All brand and product names are trademarks, registered trademarks or service marks of their respective holders. -
Page 2: Safety Information
SAFETY INFORMATION Read these safety instructions before you operate or install the equipment. Indicates a condition that can cause death or serious WARNING injury if not avoided. Indicates a condition that can cause minor or moderate CAUTION injury if not avoided. Warning, Caution Mandatory Action Prohibitive Action... - Page 3 SAFETY INFORMATION CAUTION CAUTION WARNING Use the correct fuse. The guard zone alarm is an effective aid to anti-collison. Use of a wrong fuse can result in fire or damage to the equipment. Its use does not relieve the operator of the responsibility to keep a vigilant watch on Do not place liquid-filled containers his or her surroundings.
- Page 4 SAFETY INFORMATION Warning Label(s) Warning label(s) is(are) attached to the equipment. Do not remove the label(s). If a label is missing or damaged, contact a FURUNO agent or dealer about replacement. Name: Warning Sticker Type: 03-129-1001-3 Code No.: 100-236-743-10 TFT display The high quality TFT (Thin Film Transistor) LCD displays 99.99% of its picture elements.
-
Page 5: System Configuration
SYSTEM CONFIGURATION RADAR SENSOR DRS4DL+ Pre-attached power/LAN cable 1.4 m Selectable power/LAN cable CP03-36400 (10 m) / CP03-36410 (15 m) / CP03-36420 (20 m) / CP03-36430 (30 m)* * For 24 VDC only. Multi Function Display Power supply TZTL12F/TZTL15F** 12/24 VDC TZT9/TZT14/TZTBB** ** Software upgrade to V5.01 or after is required. -
Page 6: Equipment Lists
EQUIPMENT LISTS Standard supply Name Type Code No. Remarks Radar Sensor RSB-127-120 Installation Materials CP03-35701 001-078-350 CP03-36400 000-027-211 Select one Power / LAN cable 10 m CP03-36410 000-027-212 Power / LAN cable 15 m CP03-36420 000-027-213 Power / LAN cable 20 m CP03-36430 000-027-214 Power / LAN cable 30 m... -
Page 7: Installation
INSTALLATION Installation Considerations General considerations NOTICE Do not use paint, anti-corrosion products, contact spray or other items containing organic solvents on the equipment. Organic solvents can harm paint and plastic, particularly the connectors. • The radar sensor has no power switch. Therefore, it is recommended that you con- nect the sensor to a distribution switchboard with a switch for power control. -
Page 8: Installation Of The Radar Sensor
1. INSTALLATION • To avoid electrical interference, do not run the antenna cable near other electrical equipment. Also do not run the cable in parallel to power cables. • Do not install the unit where its motor noise may affect crew or passengers. Not recommended •... - Page 9 1. INSTALLATION Tools and materials for mounting Name Usage Electric drill Drill holes for mounting. Drill bit: 11 mm Hexagonal wrench Fastening bolts: Diagonal: 6 mm Self-vulcanizing tape For water proofing of connector junction. Vinyl tape Cable tie For tying up the cable. Marine sealant For coating exposed parts of bolts.
- Page 10 1. INSTALLATION 1. Use the mounting template (supplied) to mark the location of fixing holes in the mounting platform. Be sure to drill the holes parallel with the bow. 2. From the bottom of the radome, remove flat washers (M12), spring washers (M10), flat washers (M10) and hex head bolts (M10 20).
- Page 11 • Using a cable tie, fasten the cable to the mast, etc. at the neck of each connec- tor. 6. Connect the LAN connector of the cable assembly to a LAN port on the FURUNO Multi Function Display or Ethernet HUB.
- Page 12 1. INSTALLATION Note 1: The antenna unit has no power switch. Connect the antenna unit to a dis- tribution switchboard with a switch for power control. Note 2: The antenna unit cannot accept input voltage of more than 24 VDC. Installation with the radome mount The optional radome mount lets you install the radar sensor to a mast on a sailboat.
-
Page 13: Initial Setup
• TZT9, TZT14 and TZTBB: Version 5.01 or later. TZTL12F and TZTL15F: Version 5.01 or later. Turn on the antenna unit and FURUNO Multi Function Display. Initial setup for this an- tenna must be done on the FURUNO Multi Function Display. - Page 14 2. INITIAL SETUP 4. Select [Radar Source] on the [Menu Radar] sub menus, then select the radar type connected. Note: If the antenna unit is connect- ed but does not appear in the [Ra- dar Source] list, close the list and open it again.
- Page 15 2. INITIAL SETUP Menu item Description [Antenna Longitudinal Po- Referring to the figure on the right, enter the sition] radar antenna positioning bow-stern (Longi- Origin tudinal) and port-starboard (Lateral) posi- [Antenna Lateral Position tion from the origin. (-Port)] [Auto Tuning] Enable/disable auto tuning for the connected radar.
-
Page 16: Initial Setup For Navnet Tztouch2 (Model: Tztl12F/Tztl15F)
2. INITIAL SETUP 1. Select a range between 0.125 and 0.25 NM and set the mode to “head up“. You can select a range by a pinch action. The range and range ring interval ap- pear at the bottom left of the screen. Range Range ring interval Zoom in... - Page 17 2. INITIAL SETUP 4. Drag the [Radar] menu display the menu item [Radar Initial Setup], then tap [Radar Initial Setup]. 5. Referring to the tables below, set up the radar. [Radar] menu - [Radar Initial Setup] Menu item Description [Antenna Rotation] Select the antenna rotation speed from [Auto] or [24 RPM].
-
Page 18: Check Points After Installation
2. INITIAL SETUP Correct bearing of target Displayed position of target (relative to heading) Target Target Displayed Correct position bearing of of target target (relative to heading) Antenna oriented Picture appears with Antenna oriented Picture appears with to port clockwise deviation. to starboard counterclockwise deviation. - Page 19 2. INITIAL SETUP • All washers are in place and bolts are fully tightened. • All connections are secure. • All connecting cables and wires are secured. • LAN cable is connected to the multi function display device. Turning the power on and initial setup WARNING The radar antenna emits electro- magnetic radio frequency (RF)
-
Page 20: Maintenance, Trouble- Shooting
MAINTENANCE, TROUBLE- SHOOTING WARNING NOTICE Do not use paint, anti-corrosion DO NOT OPEN THE SENSOR. Electrical shock hazard products, contact spray or other items containing organic solvents There are no user-serviceable parts on the equipment. inside. Only qualified personnel are allowed to work inside the equipment. -
Page 21: Replacement Of Fuse
Have a technician check the magnetron. Replacement of Magnetron When the life of the magnetron is reached, no targets appear on the display. If long range performance appears to have decreased, contact a FURUNO agent or dealer about replacement of the magnetron. Name Type Code No. -
Page 22: Appendix 1 Radio Regulatory Information
APPENDIX 1 RADIO REGULATORY INFORMATION USA-Federal Communications Commission (FCC) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 23: Specifications
DRS4DL+ SPECIFICATIONS OF RADAR SENSOR DRS4DL+ RADIATOR Antenna type Patch array antenna Antenna length 19-inch Horizontal beam width 5.2° typical (3 dB) Vertical beam width 25° (3 dB) Sidelobe attenuation -20 dB (within ±20°), -25 dB (±20° or more) Rotation 24 rpm RADAR FUNCTION Tx frequency... -
Page 27: Declaration Of Conformity
[DRS4DL+] Bulgarian (BG) Spanish Por la presente, Furuno Electric Co., Ltd. declara que el tipo de equipo radioeléctrico arriba mencionado es conforme con la Directiva 2014/53/UE. (ES) El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente:... - Page 28 Furuno Electric Co., Ltd. igazolja, hogy fent említett típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. (HU) címen: Maltese B'dan, Furuno Electric Co., Ltd., niddikjara li msemmija hawn fuq-tip ta' tag mir tar-radju huwa konformi mad-Direttiva 2014/53/UE. (MT) It-test kollu tad-dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ej: Hierbij verklaar ik, Furuno Electric Co., Ltd., dat het hierboven genoemde type...
- Page 32 7KH SDSHU XVHG LQ WKLV PDQXDO LV HOHPHQWDO FKORULQH IUHH )85812 $XWKRUL]HG 'LVWULEXWRU'HDOHU $VKLKDUDFKR 1LVKLQRPL\D -$3$1 $ 0$< 3ULQWHG LQ -DSDQ $OO ULJKWV UHVHUYHG $ 2&7 3XE 1R ,0( $ 7$68 '56'/ ...