Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Furuno PG-1000
Summary of Contents for Furuno PG-1000
- Page 1 INTEGRATED HEADING SENSOR PG-1000 MODEL...
- Page 2 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n Te l e p h o n e : 0 7 9 8 - 6 5 - 2 111 Te l e f a x : 0 7 9 8 - 6 5 - 4 2 0 0...
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS Safety Information for the Installer WARNING Turn off the power at the mains switchboard before beginning the installation. Post a sign near the switch to indicate it should not be turned on while the equipment is being installed. Fire or electrical shock can result if the power is left on or is applied while the equipment is being installed. - Page 4 FOREWORD A Word to PG-1000 Owners Congratulations on your choice of the FURUNO PG-1000 Integrated Heading Sensor. We are confident you will see why the FURUNO name has become synonymous with quality and reliability. For over 50 years Furuno Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment.
-
Page 5: Table Of Contents
TABLE OF CONTENTS SYSTEM CONFIGURATION ... iv SPECIFICATIONS...SP-1 1 INSTALLATION 1.1 Equipment List ... 1 1.2 Selecting Mounting Location ... 2 1.3 Mounting ... 3 1.4 Connections ... 4 1.5 Correcting Magnetic Field Distortion (Deviation) ... 5 1.6 Heading Alignment ... 6 1.7 Setting Output Data ... -
Page 6: System Configuration
Magnetic or true heading Magnetic Magnetic or true variation data heading Magnetic or true heading Deviation at the PG-1000 can be corrected from the Remote Display DD-2000. 10.0 - 35.0 VDC GPS NAVIGATOR (ex: GP-1610C) CURRENT INDICATOR (ex: CI-1000) Course CSE 88.8... -
Page 7: Specifications
SPECIFICATIONS OF INTEGRATED HEADING SENSOR The PG-1000 is an electromagnetic compass consisting of a fluxgate and a solid-state rate gyro, supported with advanced software. The heading information is outputted in IEC 61162-1 or NMEA format. For high data speed, AD-10 format (25 ms) is also available. The heading information is used for radar, AIS, ECDIS, automatic steering system and other navaids. -
Page 8: Installation
1 INSTALLATION 1.1 Equipment List Standard set l l a i t a Installation materials (CP64-02000) t a l Optional units - - -... -
Page 9: Selecting Mounting Location
1.2 Selecting Mounting Location The PG-1000 must be indoor on the horizon- tal plane. When selecting a mounting location, keep in mind the following points: • The ambient temperature must be between -15 C and 55 C. • Vibration at the mounting location should be minimal. -
Page 10: Mounting
For added support, use nuts, bolts and washers. o Secure sufficient clearance around the sensor for maintenance and checking. Figure 7 Mounting the PG-1000 Note: Do not overtighten the screws or bolts; the sensor may crack. Bow mark Material: Brass... -
Page 11: Connections
Checking for inclination Make sure that the PG-1000 is mounted hori- zontally by the following checks. 1. Press the [TRUE] and [+] keys more than two seconds. When the inclination is within 5 , STATUS LED lights and TRUE LED blinks. -
Page 12: Correcting Magnetic Field Distortion (Deviation)
The magnetic field at the sensor around ship is subjects to change with the ship structure, engins, electronic equipment or any ferrous materials in the vicinity. The PG-1000 contains an automatic correction facility against magnetic field distortion aboard the ship. 1. Do this procedure in a calm water. -
Page 13: Heading Alignment
The deffault setting is 100 ms. 1. Disconnect the power connector from the sensor. 2. Reattach the connector to the sensor while pressing the [+] key. The PG-1000 is pow- ered on, and the current output interval is shown by the LEDs. AUTO... - Page 14 The default setting is HDG. 1. Disconnect the power connector from the sensor. 2. Reattach the connector to the sensor while pressing the [-] key. The PG-1000 is pow- ered on, and LED(s) light to show which output sentence(s) is being output. AUTO...
-
Page 15: Correcting Magnetic Anomalies
Corrects the heading. Selects output data format; magnetic or true Turns on and off deviation corrections. Figure 18 Front panel of PG-1000 2.2 Turning the Power On/Off Note: You may leave port after the STATUS LED begins lighting (not blinking). -
Page 16: Automatic Distortion Compensation
Note 2: Correct distortion whenever you feel error is excessive. 2.4 Selecting Output Data Format The PG-1000 can output heading true or mag- netic. The default setting is magnetic heading in AD-10 format. CAUTION CAUTION Turn off the autopilot before selecting output data format. -
Page 17: Maintenance & Troubleshotting
3 MAINTENANCE & TROUBLESHOOTING 3.1 Maintenance Regular maintenance is important to maintain intended performance over a long period. Regularly check the following: • Clean the component with a soft cloth. Do not use chemical cleaners; they can remove paint and markings. •... -
Page 18: Diagnostic Test
3.3 Diagnostic test The PG-1000 has a self-test which checks the circuit board and keys for proper operation. LED/KEY/ROM/RAM test 1. Disconnect the power cable from the equip- ment. 2. While pressing the [AUTO] key, reattach the power cable. The test sequence is as below. -
Page 19: Displaying Program Version No
4. Disconnect the power cable off from the equipment, and then reattach it. 5. Mount the equipment at the previous posi- tion, referring to page 3. 3.4 Displaying Program Version No. When the equipment is powered on, the pro- gram no., denoted by LEDs in binary notation, is shown about 1 second. -
Page 20: Parts Location And List
PARTS LOCATION AND LIST C PU B o a rd PG-1000, cover opened AP-1...
Need help?
Do you have a question about the PG-1000 and is the answer not in the manual?
Questions and answers