Download Print this page

Axxess INSTGMBTI-4 Installation Instructions

Gm lan interface for handsfree bluetooth car kits

Advertisement

Quick Links

INSTGMBTI-4
3. Insert the 44 pin Plug on harness 1 into the rear of
the radio.
4. Connect the 44 pin cap on harness 1 to the 44 pin
plug connected to the vehicle (the connector that
was removed from the back of the radio).
5. Connect the 20 pin black connector (harness 2) to
the GMBTI-2 module.
6. Connect ISO to 8 way (harness 3) to the 8 way por-
tion of harness 2. NOTE: The 12 pin black connec-
tor will not be used.
7. Plug the ISO side of the ISO to 8 way harness into
the mating Parrot connectors.
8. Take the Mute wire of the Parrot kit and plug it into
the "Mute 1" wire in the Parrot ISO harness.
9. Finish installing the rest of the Parrot hands free kit
and reinstall the OEM radio.
10. Reconnect the vehicles battery.
OPERATION
Refer to the Parrot manual for operation. Adjust the
volume of the handsfree kit by turning the volume knob
of the radio. Audio from any source will be muted when
a call comes in or a call is made.
4
INSTGMBTI-4
OTHER HANDS FREE KITS
Other handsfree kits can be used with the GMBTI-4.
Follow the steps below to wire the handsfree kit:
1. Using the ISO to 8 way connector harness cut the
ISO ends off.
2. The Yellow wire will go to the Battery wire of the
handsfree kit
3. The Red wire will go to the 12 volt accessory wire
of the handsfree kit
4. The Black wire will go to the ground of the hands-
free kit
5. The Purple wire will go to the Mute wire of the
handsfree kit
6. The White wire will go to the (+) speaker output of
the handsfree kit
7. The White/Black wire will go to the (-) speaker out-
put of the handsfree kit
Handsfree kits may have more then one speaker output
on their harnesses however the GMBTI-4 needs only
one speaker output to use.
K
NOWLEDGE IS
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certifi ed technicians
5
METRA. THE WORLD'S BEST KITS.™
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INSTGMBTI-4
GM LAN INTERFACE
FOR HANDSFREE
BLUETOOTH CAR KITS

INSTALLATION INSTRUCTIONS

READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTING ANY INSTALLATION
The GMBTI-4 is designed to integrate a Handsfree
Bluetooth Car Kit into General Motors vehicles that
have the 44 Way LAN data system. The OEM radio will
mute when a call comes in and the audio will be heard
through the front speakers. The GMBTI-4 is Plug-N-
Play for the Motorola IHF1000/1700 and Parrot car kits,
and it can be used with other car kits with modifi cations.
APPLICATIONS
P
OWER
METRA. THE WORLD'S BEST KITS.™
1-800-221-0932
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
CHEVROLET
2010 Camaro
2010 Equinox
GMC
2010 Terrain
metraonline.com

Advertisement

loading

Summary of Contents for Axxess INSTGMBTI-4

  • Page 1: Installation Instructions

    INSTGMBTI-4 INSTGMBTI-4 INSTGMBTI-4 3. Insert the 44 pin Plug on harness 1 into the rear of OTHER HANDS FREE KITS GM LAN INTERFACE the radio. Other handsfree kits can be used with the GMBTI-4. FOR HANDSFREE 4. Connect the 44 pin cap on harness 1 to the 44 pin...
  • Page 2 INSTGMBTI-4 INSTALLATION COMPONENTS INSTALLATION PROCEDURE OPERATION 1. Disconnect the vehicle battery. Refer to the Motorola IHF1000/1700 manual for opera- A. GMBTI-4 interface 2. Remove the radio from the dashboard, and discon- tion. Adjust the volume of the hands free kit by turning B.