Delta 600VA Installation And Operation Manual

Delta UPS – Agilon Family
VX Series, Line-interactive
600-1500 VA
Installation & Operation Quick Guide
ENGLISH
1

Package Inspection

No. Item
1 UPS
2 Quick Guide
3 USB Cable
4 Output Power Cord (10A)
Remove the UPS from its package and inspect it for damage that may have
occurred during shipping. If any damage is discovered, re-pack the unit and
return it to the place of purchase.
2
Front Panel & Rear Panel
600VA
(Front Panel)
1
6
2
4
5
1000VA
(Front Panel)
1
2
3
1500VA
(Front Panel)
1
2
7
3
www.deltapowersolutions.com
No.
LED Indicator
(Only For 600VA Model)
1
LCD Touch Panel (Only For
1000VA/ 1500VA Model)
ON/ OFF Button
2
Output Socket
3
3
Operation
y y
Connect to Utility Power
Q'ty
Connect the AC power cord to the utility power. Then, the UPS will start
1 PC
to charge its inside battery (batteries). For best result, charge the battery
1 PC
(batteries) for 6 hours prior to initial use. It is not recommended to connect
the UPS's AC power cord to any generator.
1 PC
y y
Plug in Equipment
1 PC
Plug your equipment to the Output Socket on the rear panel of the UPS.
(Rear Panel)
y y
Connect to USB Port and Install Software
Connect one end of the supplied USB cable to your PC and the other to
the USB port located at the rear of the UPS. Download the latest version of
ViewPower software (http://www.deltapowersolutions.com/en/mcis/600va-
1500va-single-phase-ups-vx-series-software-download.php) to your hard
3
drive. Follow on-screen instructions to complete the software installation.
y y
Turn On/ Off the UPS
When the UPS is OFF, press the ON/ OFF Button to turn on the UPS and
the LED/ LCD will be on. When the UPS is ON, press the ON/ OFF Button
to turn off the UPS and the LED/ LCD will shut off.
(Rear Panel)
y y
Fuse Replacement
When the UPS always runs in battery mode, it might be because the fuse
6
is damaged. If yes, please follow the following procedures to replace the
fuse.
1 Remove the fuse cover from the rear panel.
4
5
(Rear Panel)
6
2 Replace the original fuse
4
5
3
Replace the fuse cover back to the rear panel.
Item No. Item
4 AC Input
5 Fuse
USB Port
6
Cooling Fan
7
(Only For 1500VA Model)
WARNING:
1. Make sure that the UPS is powered on to protect all important
devices from data loss during power failure.
2. NEVER connect a laser printer or scanner to the Output
Socket of the UPS. The equipment may draw significant
power to overload the UPS.
(1500VA)
(Pull)
(Fuse Cover)
with the provided backup fuse
1
2
(Take Out)
1
4
LED Indicator
LED
ON
ON Sounds all the time
Flashing
Flashing Sounds every second
OFF
5
LCD Display
y y Operation Display:
UPS Mode
UPS
Power On
AC Mode
When AVR is functioning,
second.
Overload
In AC
Mode
Battery
Mode
Original Fuse
When battery level is low,
(Provided)
Overload
In Battery
Mode
Backup Fuse
(Provided)
NOTE:
.
2
If backlight shuts off, you can activate it by touching the screen.
Continue to the Next Page
(Install)
(Only For 600VA Model)
Alarm UPS Status
The main AC power is normal
OFF
and the UPS runs normally.
UPS fault.
Sounds every Power failure occurs and the
10 seconds UPS runs in battery mode.
Low battery.
OFF The UPS is off.
(Only For 1000VA/ 1500VA Model)
LCD Touch Panel Description
When the UPS is powered
on, it will enter this mode for
4 seconds.
LCD information will be
displayed in the following
order when the LCD
is touched.
1. Output voltage
2. Input voltage
icon will flash every 3. Load level
4. Battery capacity
When overload occurs,
alarm will beep every 0.5
second.
icon will flash.
Alarm will beep every
10 seconds and LCD
information will be displayed
in the following order
when the LCD is touched.
1. Output voltage
2. Input voltage
3. Load level
icon will flash.
4. Battery capacity
When overload occurs,
alarm will beep every 0.5
second.
icon will flash.
