Basic Parameters (Control Keypad: Menu M2 G2.1) - Vacon NXP User Manual

14 • vacon
6.2 Basic parameters (Control keypad: Menu M2
Code Parameter
P2.1.1 Max frequency
P2.1.2 Acceleration time 1
P2.1.3 Deceleration time 1
P2.1.4 Current limit
Nominal voltage of
P2.1.5
the motor
Nominal frequency
P2.1.6
of the motor
Nominal speed of
P2.1.7
the motor
Nominal current of
P2.1.8
the motor
P2.1.9 Motor cosϕ
P2.1.10 I/O Reference
Keypad control
P2.1.11
reference
Fieldbus control
P2.1.12
reference
Jogging speed
P2.1.13
reference
P2.1.14 Preset speed 1
P2.1.15 Preset speed 2
P2.1.16 Preset speed 3
P2.1.17 Preset speed 4
P2.1.18 Preset speed 5
P2.1.19 Preset speed 6
P2.1.20 Preset speed 7
Table 3. Basic parameters G2.1
6
shaft synchronization application – parameter lists
Min Max Unit
Par. 2.1.1 320,00 Hz
0,1 3000,0 s
0,1 3000,0 s
0,4 x I 2 x I A
H H
180 690 V
30,00 320,00 Hz
300 20 000 rpm
0,4 x I 2 x I A
H H
0,30 1,00
0 14
0 9
0 9
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
0,00 Par. 2.1.2 Hz
G2.1)
Default Cust ID
50,00 102
1,0 103
1,0 104
I 107
L
NX2: 230V
NX5: 400V 110
NX6: 690V
50,00 111
1440 112
I 113
H
0,85 120
0 117
8 121
9 122
5,00 124
10,00 105
15,00 106
20,00 126
25,00 127
30,00 128
40,00 129
50,00 130
Tel. +358 (0)201 2121 • Fax +358 (0)201 212 205
Note
NOTE: If f > than the
max
motor synchronous speed,
check suitability for motor
and drive system
Check the rating plate of
the motor
The default applies for a 4-
pole motor and a nominal
size frequency converter.
Check the rating plate of
the motor.
Check the rating plate of
the motor
0=AI1
1=AI2
2=AI1+AI2
3=AI1-AI2
4=AI2-AI1
5=AI1xAI2
6=AI1 Joystick
7=AI2 Joystick
8=Keypad
9=Fieldbus
10=Motor potentiometer
11=AI1, AI2 minimum
12=AI1, AI2 maximum
13=Max frequency
14=AI1/AI2 selection
0=AI1
1=AI2
2=AI1+AI2
3=AI1-AI2
4=AI2-AI1
5=AI1xAI2
6=AI1 Joystick
7=AI2 Joystick
8=Keypad
9=Fieldbus
See par. 2.1.12
Multi-step speed 1
Multi-step speed 2
Multi-step speed 3
Multi-step speed 4
Multi-step speed 5
Multi-step speed 6
Multi-step speed 7