Download Print this page

Casio Oceanus OCW-G2000S-1A Operation Manual page 21

Hide thumbs

Advertisement

Table of Contents
Auto Time Adjustment by
Bluetooth Connection (Time
Adjustment)
Q1
When does the watch sync its time
setting with the phone?
The watch will connect with the phone and
perform auto time adjustment at around 12:30
a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The
connection is automatically terminated after
auto time adjustment is complete.
Q2
Auto time adjustment is performed,
but the time setting is not correct.
Is auto time adjustment not being
performed according to its normal
schedule?
Note that auto time adjustment is not
performed for 24 hours after swapping of
the Home Time and World Time, or after
the time setting is adjusted manually on
the watch. Auto time adjustment will
resume 24 hours after either of the above
operations is performed.
Is the watch in the Airplane Mode?
Auto time adjustment will not be
performed at the scheduled times if the
watch is in the Airplane Mode. Exit the
watch's Airplane Mode.
Using the Watch in a Medical Facility or
l
Aircraft
Q3
Time is not displayed correctly.
The phone's time setting may be incorrect
because it is unable to connect with its
network due to being out of range, etc. If this
happens, connect the phone to its network
and then adjust the time setting.
Operation Guide 5501
Hand Movement and
Indications
Q1
I don't know what mode the watch is
in.
You can determine the current mode by
checking the disk. Use (C) to navigate
between modes.
Navigating Between Modes
l
Q2
The second hand is jumping at two-
second intervals.
Battery power is low. Keep the watch exposed
to light until it recharges sufficiently.
Solar Charging
l
Q3
All hands are stopped and buttons do
not work.
The battery is dead. Keep the watch exposed
to light until it recharges sufficiently.
Solar Charging
l
Q4
The hands suddenly start moving at
high speed.
This is due to one of the reasons below, and
does not indicate malfunction. Simply wait
until normal hand movement resumes.
The watch is recovering from a power
saving state.
Power Saving
l
The hands are moving to their new positions
following a GPS signal or time calibration
signal receive operation.
Time Adjustment (GPS, Time Calibration
l
Signal)
Establish a connection with the phone and
correct the time setting.
Auto Time Adjustment
l
Q5
Hands are stopped and buttons do
not work.
The watch is in the charge recovery mode.
Wait until the recovery process is complete
(for about 15 minutes). The watch will recover
more quickly if you place it in a brightly lit
location.
Q6
Why is the current time indicated by
the watch is off by a large amount of
time (nine hours, three hours and 15
minutes, etc.)?
The city setting is not correct. Select the
correct setting.
Acquiring GPS Position Information
l
Manually
Setting a Home Time City
l
Q7
The current time indicated by the
watch is off by one hour or 30
minutes.
The summer time setting is not correct. Select
the correct setting.
Acquiring GPS Position Information
l
Manually
Setting a Home Time City
l
Q8
The hand and/or day indicator are not
aligned correctly.
Strong magnetism or impact can cause the
hands and/or the indicator to go out of
alignment. Adjust hand and/or day indicator
alignment.
Adjusting Hand and Day Indicator
l
Alignment
Crown Operations
Q1
Nothing happens when I rotate the
crown.
If you do not perform any operation for about
two minutes after pulling out the crown
(approximately 30 minutes in the case of hand
and day indicator alignment), crown
operations will automatically become
disabled. Push the crown back in to its normal
position and then pull it out again to re-enable
crown operations.
Using the Crown
l
21

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Casio Oceanus OCW-G2000S-1A

This manual is also suitable for:

Oceanus ocw-g2000c-1a