Page 1
Q-Serie: Smart Home Alarm Manual Installation and operation of the Blaupunkt Q-Series Enjoy it. IP-Alarm System Smart Home Alarm Blaupunkt Competence Center Security...
Table of Contents 1. Introduction and registration 1.1 Preparation 1.2 Registration 1.3 Handling error massages during registration 1.4 Confirmation of registration and log-in 2. Extension of the security system 3. Assembly and planning of the security system 3.1 Kit Content Installation 3.2 General instructions for installation 3.3 Before mounting: walk test 3.4 Tamper protection...
Page 3
NOTE: Information and illustrations are subject to chage within the document. Blaupunkt reserves the right to alter the specification and product design at any time without notice.
1. Introduction and registration These instruction is intended to help you with the installation and operation of your Blaupunkt Q Series Smart Home Alarm System. You can download the Secure4Home app for free from the Apple Store or Google Play.
Follow the link on the e-mail and log in to the server. To do this, enter the registered username and the registered password. Registration is now complete. If you do not receive a confirmation e-mail, please check your spam folder. Blaupunkt Competence Center Home Security...
SRAC-S1 SD-S1 Detector CO-S2 HD-S1 WS-S1 Hazard Alert Radiator Thermostat 5in1 Multi Detector Smart Power Meter Power Meter Relay Roller Shutter Smart System TRV-S1 MD-S1 Switch PSM-S1 PRM2-S1 Relay SCM-S1 Thermostat TMST-S1 Switch Smart Home Blaupunkt Competence Center Home Security...
3. Assembly and planning of the security system IMPORTANT: Before you install the devices, you should first register the system in the Blaupunkt Home Portal at https://eu.bphomeconnect.com/. 3.1 Kit Content Installation Panel System mode-LED (Green/Red): Status-LED (Amber /Red): Network-LED (Amber): Green ON –...
Page 8
Fig.3 Remote-Control (Q3200 KIT) (RC-R3B) (Fig.4) LED-Display Arm Away-Button Arm Home-Button With the RC-R3B you can operate your Blaupunkt security system comfortably. By pressing the buttons, Emergency- it’s possible to change the system arm mode and Button trigger an emergency alarm.
• It must be connected to your • Do not point the PIR sensor router via Ethernet. at window, or heat sources directly, such as stove, boilers or radiators. Blaupunkt Competence Center Home Security...
5.Place the DC-S1 cover again onto the base. Make sure that the tamper protection is pushed down, other- wise the tamper will be triggered. 6.Repeat the same process for the magnet. The magnet should be installed adjacently at the sensor marker. Blaupunkt Competence Center Home Security...
Page 11
4. Fix the IRC-S2 back cover onto the wall with the screws and plugs provided. 5. Place the IRC-S2 again onto the back cover. Make sure that the tamper protection is pushed down, otherwise the tamper will be triggered. Corner Fixing Knock-outs x4 Surface Fixing Knock-outs x 2 Blaupunkt Competence Center Home Security...
If there is any failure on a device, the device will be marked with a red line and the error status is displayed. Additionally, here it is possible to manually take a picture with the PIR camera by clicking on the button. Blaupunkt Competence Center Home Security...
4.1.3 IP cameras The IP Camera List displays the IP cameras learned in the alarm panel. Click on the IP camera image to get to the IP Camera page and see the video live stream. Blaupunkt Competence Center Home Security...
The Automation page provides access to the home automation features of the alarm system. 4.2.1 Device All home automation accessories are displayed on this page. Here you can have an overview, manage and use each of them individually. Blaupunkt Competence Center Home Security...
In the group menu you can assign several devices to a group. For example, you can map the devices in a room to a specific group, easily monitoring the status of all devices in a room. Blaupunkt Competence Center Home Security...
/ portal or triggered automatically by linking them to other sensors. Refer to point 4.2.3.2 for some examples. You add up to 3 actions per scene and a maximum amount of 10 scenes. Blaupunkt Competence Center Home Security...
Click Submit to confirm the scenario setting. The new scenario will now be displayed in the list. Whenever you want to trigger a scene manually click Apply to trigger the desired scene manually. This is also possible via the app. For more information, refer to “Secure4Home App”. Blaupunkt Competence Center Home Security...
On “Action Type” select “Request Image”, then select the IRC-S2 (PIR-Camera) and press “Submit”. Step 2: Once the scenario is created go to Settings> Devices. Click the three dots on the right of the desired door contact to open the sensor settings. Blaupunkt Competence Center Home Security...
Page 19
Step 2: Once the scenario is created go to Settings> Devices. Click the three dots at the right of the desired motion detector to open the sensor settings. For images please refer to “Example 1” Blaupunkt Competence Center Home Security...
4.2.3.3 Delete a Scene Step 1 Click on the icon and select which scenario you want to delete. Then confirm with OK to delete the scenario. Blaupunkt Competence Center Home Security...
4.2.4.1 Create a Rule Step 1 Click on the Icon to get to the Add Rule menu. Step 2 Enter a Name for the rule. Step 3 Select a Trigger for the rule (e.g. Schedule). Blaupunkt Competence Center Home Security...
Page 22
Optional: To add more than 1 action to a rule click the + icon at the right to add a new action for the current rule. (up to 3 actions per rule). Step 6 Click Save to confirm the rule setting. The new rule will now be displayed in the rule list. Blaupunkt Competence Center Home Security...
Click Submit to confirm the rule change. Activate / Deactivate a rule Click the ON / OFF switch button to activate or deactivate a rule. A rule with the switch button green means that its activated while in grey means deactivated. Blaupunkt Competence Center Home Security...
4.2.4.3 Delete a Rule Step 1 Click on the Icon, to get to the “delete rule” menu. Step 2 Check the box in front of the rule and click OK. Blaupunkt Competence Center Home Security...
The Q-Hub should switch on the Smart Power Switch Meter plug (PSM-S1) every day at 07:00, only if the alarm system is armed. This would look like this: 2. Example The disarming of the Q-Hub automatically opens roller shutter A and roller shutter B. This would look like this: Blaupunkt Competence Center Home Security...
The Event page displays all alarm / status events, pictures and videos transmitted by the alarm panel. Using the icons, you can filter media or alarm events, or search for events on a specific date. Blaupunkt Competence Center Home Security...
Please refer to 4.2.3 Scene for scenario creation and exam- ples. • Chime: If chime function is enable the Q-Hub will emit a double “beep” sound notification whenever this sensor gets triggered under Home or Disarm mode. Blaupunkt Competence Center Home Security...
Page 28
Note: If the panic button on the remote control is triggered, the control panel can no longer be disarmed by the same remote control. This must be done with another device or the app. Click Submit when you have finished setting the device and want to save it. Blaupunkt Competence Center Home Security...
6 or higher is recommended. If no signal is received or bellow 5, please choose a different mounting location and run the test again. With the IP camera, the signal is transmitted automatically upon entering Walk Test and does not require button press. IP Camera will be displayed always as 0. Blaupunkt Competence Center Home Security...
Check the box in front of accessory info, and click OK to add the accessory into the Q-Hub. The device will be assigned automatically to the first available empty zone number. Refer to 4.6.1 Setting the devices to set up the accessory configurations. Blaupunkt Competence Center Home Security...
30 seconds to alert the user of a failure. • Disarming Beep: Here you can adjust the volume for the disarming notification sound (low, medium or high volume). Blaupunkt Competence Center Home Security...
• Low Temperature: When temperature drops below the set value, the Q-Hub will notify the user about the Low Temperature condition. If the temperature rises above the set value again, the Q-Hub will send Low Tem- perature Restore report to the user. Blaupunkt Competence Center Home Security...
• Siren Tamper: By selecting OFF it will disable temporarily the siren’s tamper protection function for one hour. You can also reactivate the siren tamper protection by selecting ON again. This function should be used to avoid a tamper alarm whenever you wish to change the siren location or batteries. Blaupunkt Competence Center Home Security...
Code. If they are identical, the System Mode change will not work. 4.7.7 Time Setting Under “Time Zone Setting” open the dropdown menu and select your time zone Use the Date & Time Settings to configure the date and time Blaupunkt Competence Center Home Security...
The Report setting page allows you to program the system notification path. Call notifications: With the premium service, user will be able to receive telephone calls from Blaupunkt Calling Alarm Center. Whenever the Q-Hub detects an intrusion it will send a report to our Calling Alarm Center, and perform auto- maticly loop calls to your telephone number.
Page 36
0, the server stops calling. The status of your call credit can be seen by hovering the mouse over the icon. You have 12 call credits per month. Refer to premium.blaupunkt-security.com for more information regarding the premium service. Blaupunkt Competence Center Home Security...
Page 37
Check the boxes of the e-mail addresses you want to remove at the right end of the e-mail address list and click Submit to remove the selected e-mail addresses from the system. The default e-mail address can not be deleted. Blaupunkt Competence Center Home Security...
“Account”. This page displays your registered user info, secondary user account list, language and push notifications settings. Please click on the icon to edit the account information (see screenshot below). Blaupunkt Competence Center Home Security...
Page 39
“Remove ac- count” function. Check the boxes of the accounts you want to remove at the right end of the user account list and click Submit to remove the selected user accounts from the system. Blaupunkt Competence Center Home Security...
Page 40
To keep your account secure from hackers we recommend a strong password with at least 8 characters includ- ing lower letters, upper letter, numbers and special symbols. • Account Info: Click icon to access to your account info where the MAC address of the panel and the account number will be displayed. Blaupunkt Competence Center Home Security...
Page 41
None: No event will be report All: Alarm and status events will be reported. Burglar: Only alarm events will be reported Click “SUBMIT” to confirm after finishing all settings. Blaupunkt Competence Center Home Security...
The Service and Payment page displays the user account service package choices. With the premium service, the user will be able to receive telephone calls from Blaupunkt Calling Alarm Center. Our premium service call notifications will provide the peace of mind that whenever the Q-Hub detects an intrusion it will send a report to our Calling Alarm Center, and perform automaticly loop calls to your telephone number.
Activate “Stay logged in” for the app to save your credentials for the next time. After successfully logging in, you will first be redirected to the “Security” page. To switch between the function pages, tap the respective function icons at the bottom. Blaupunkt Competence Center Home Security...
Contact will be also marked in red. Tap once on the accessory to check the status and the error message. Use the button to filter and display only accessories with any kind of error. Use the button to filter and display only Door Contacts with Open status. Blaupunkt Competence Center Home Security...
By clicking on the scene its possible to check the actions of that scene. Group: On the group menu its possible to manage the accessors by groups. To link accessories to a certain group please use the Web Home Portal. Blaupunkt Competence Center Home Security...
Page 46
This menu allows the user to activate / Deactivate any existing rule. Click the ON / OFF switch button to activate or deactivate a rule. A rule with the switch button green means that it’s activated while in grey means deactivated. Blaupunkt Competence Center Home Security...
In this sub-menu you can manage the motion detector with camera (IRC-S2). Click the icon to take a photo with the IRC-S2. The snapshot will be loaded to the Home Portal and dis- played on the Event menu. Blaupunkt Competence Center Home Security...
Press a event for details as Date, Time, and accessory triggered. Additionally events captured by the IRC-S2 will display the captured photo. Press the phone button to access the telephone function to make a call Press the mail button to forward and share this event via mail or whatsapp. Blaupunkt Competence Center Home Security...
Alarm type push notification. Any other push notification uses the standard notification tone from your phone and won’t disturb you if the phone is on silence mode. Blaupunkt Competence Center Home Security...
Page 50
About: Under this menu it will be displayed the Blaupunkt Technical support contact Info according to your app lan- guage. Additionaly, at the bottom can be found the App version. Blaupunkt Competence Center Home Security...
Check on the device menu for any accessory with tamper error. Refer to the accessory manual to locate the tam- per and check if it’s properly pressed. • Radio interference: Perform Walk Test on all your accessories to check if Q-Hub can still receive their signals. Blaupunkt Competence Center Home Security...
If using a IR-S1L make sure that pets do not have access to the secure area. For a pet immune motion detector please use a IRP-S1L. Make sure that the motion detector is not aiming at a source of heat or moving objects. Blaupunkt Competence Center Home Security...
• Reconnect the power plug while holding down the red button on the back. • Press the button for about 5 seconds until the alarm panel emits a long beep and all 3 LEDs light up. • Release the button: the factory reset is complete. Blaupunkt Competence Center Home Security...
• Emergency power supply: 15 hours Wireless Motion detector • Radio frequency: 868 MHz • Battery: 1 x 3 V lithium battery Wireless Door / Window Sensor • Radio frequency: 868 MHz • Battery: 1 x CR2 3V lithium battery Blaupunkt Competence Center Home Security...
This device complies with the requirements of the R & TTE Directive 1999/5 / EC and the following unified standards have been met: Health: EN62479:2010 Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EMC: EN 301 489-1 V1.9.2:2011 EN 301 489-3 V1.6.1:2013 EN 301 489-17 V2.2.1:2012 Radio: EN 300 328 V1.8.1:2012 EN 300 220-1 V2.4.1:2012 EN 300 220-2 V2.4.1:2012 Blaupunkt Competence Center Home Security...