Blaupunkt Q Series Manual
Home portal server
Hide thumbs
Also See for Q Series:
- Installation and operation manual (56 pages) ,
- Installation and operation manual (39 pages)
Subscribe to Our Youtube Channel
Related Manuals for Blaupunkt Q Series
Summary of Contents for Blaupunkt Q Series
- Page 1 For Q & Q-Pro Series Manual Home Portal Server for Blaupunkt Q-Series Enjoy it. IP-Alarm System Smart Home Alarm Blaupunkt Competence Centre Security...
-
Page 2: Table Of Contents
Table of Contents Contents 1. Introduction and registration....................................3 1.1 Preparation........................................3 1.2 Registration........................................4 1.3 Handling error messages during registration..........................5 2. Operation through the web portal..................................6 2.1 Security..........................................6 2.1.1 Sensors......................................6 2.1.2 System Modes..................................7 2.1.3 IP cameras....................................7 2.2 Automation........................................8 2.2.1 Device......................................8 2.2.1.1 Power switch..............................9 2.2.1.2 Roller shutters 9 2.2.1.3 Thermostat and Radiator........................10 2.2.1.4 Smart Lights..............................11... - Page 3 If the device is updating, please don’t turn it off since it could harm the Security System. NOTE: Information and illustrations are subject to change within the document. Blaupunkt reserves the right to alter the specification and product design at any time without notice.
-
Page 4: Introduction And Registration
1. Introduction and registration These instructions are intended to help you with the operation of your Blaupunkt Q Series Smart Home Alarm System. You can download the Secure4Home app for free from the Apple Store or Google Play. IMPORTANT: Be sure to read the quick start guide that comes with the kit. It contains important information and helps to get the system up and running quickly. -
Page 5: Registration
Registration is now complete. If you do not receive a confirmation e-mail, please check your spam folder. The Secure4Home App is intended to register and manage your Security System from anywhere. For configuration please refer to chapter 2. Operation through the Web Portal. Blaupunkt Competence Centre Home Security... -
Page 6: Handling Error Messages During Registration
Error with MAC address: Each MAC address can only be registered once. Otherwise, an error message will be displayed. If you are the owner of the panel and have not previously registered this panel, please contact Blaupunkt Support. NOTE: Using LTE routers and powerline adapters can cause problems. Blaupunkt Competence Center Home Security... -
Page 7: Operation Through The Web Portal
Additionally, it is possible to manually take a picture with the PIR camera (IRC-S2 or IRC-P4) by clicking on the button and a video recording with the Video camera (IPC-S1) by clicking on the button. Blaupunkt Competence Centre Home Security... -
Page 8: System Modes
The IP Camera List will display a preview image for the IP Cameras (IPC-S1) learned in the alarm panel (up to 3 cameras). Click on the IP camera image to get to the IP Camera page and see the video live stream. Blaupunkt Competence Center Home Security... -
Page 9: Automation
If there is any failure on a device (E.g. battery low, supervision failure), the device will be highlighted in red and the error will be displayed under the “Fault” column. On this page, it’s possible to do some basic operation as turning ON /OFF or dimming a device. Blaupunkt Competence Centre Home Security... -
Page 10: Power Switch
Status column. Click on the 3 dots from the right to open a more in-detail energy consumption chart. At the drop-down menu, you can choose to display the last 2 hours, 24 hours, 7 days or 30 days. Blaupunkt Competence Centre Home Security... -
Page 11: Thermostat And Radiator
The radiator TRV-S1 is usually installed at the corner of the room and near the heating pipe. As a result, it’s temperature reading may deviate from room temperature at the centre room. Use the Setpoint Offset function to compensate for the deviation. Blaupunkt Competence Centre Home Security... -
Page 12: Smart Lights
Philips Hue, Osram Lightify, Müller Licht tint. Other Zigbee smart lights brands might also be compatible but have not been tested by Blaupunkt and complete compatibility cannot be assured. The smart light must not be paired or connected to any other panel or HUB (Phillips HUB included). If the smart light is paired to other panel or HUB, please perform a factory reset on the smart light. - Page 13 (yellowish) and at the right cool light (white). Then click “Apply” at the bottom right. On the pre-set sub-menu, it’s possible to select some pre-set colours in order to change to the desired colour in an easy and fast way. Blaupunkt Competence Centre Home Security...
-
Page 14: Room
• To delete accessories from a room, select the desired room and click the icon top right corner of the accessories list. • To add accessories to a room, select the desired room and click the icon top right corner of the accessories list. Blaupunkt Competence Center Home Security... -
Page 15: Groups
At the right column above the device list, some device types will low the user to modify values for all the accessories from the group. (E.g. dimming, temperature setpoint or colour). Click the icon to send the action. Blaupunkt Competence Centre Home Security... -
Page 16: Scene
Here you can create a scenario by clicking on the - Click symbol from the left column. Step 2 Enter a name for the scenario. Step 3 Choose an icon for the scenario that you can easily recognize. Blaupunkt Competence Centre Home Security... - Page 17 Then confirm with OK to delete the scenario. 2.2.4.3 Edit a Scene Select the scene you want to edit from the left column. Then click on the icon from the right column. Blaupunkt Competence Center Home Security...
-
Page 18: Rule
2.2.5.1 Create a Rule Step 1 Click on the Icon to get to the Add Rule menu. Step 2 Enter a Name for the rule. Step 3 Select a Trigger to start the rule (e.g. Schedule). Blaupunkt Competence Center Home Security... - Page 19 Scenes already have up Step 6 Click Save to confirm the rule setting. The new rule will now be displayed in the rule list. Blaupunkt Competence Centre Home Security...
- Page 20 A rule with the switch button green means that its activated and will start when the trigger and conditions are met. While the switch button in grey means deactivated and won’t start even if the rigger and conditions are met. Blaupunkt Competence Center Home Security...
- Page 21 2.2.4.3 Delete a Rule Step 1 Click on the Icon, to get to the “delete rule” menu. Step 2 Check the box in front of the rule and click OK. Blaupunkt Competence Centre Home Security...
- Page 22 Note: Make another rule (e.g. at 22:00) to close the blinds and turn the lights OFF. Turn on the lights when you arrive home Whenever you open the door of your home between (e.g. 19:00 and 7:00) turn the lights (PSM-S1, PRM-S2 or smart lights) ON for 30 seconds. Blaupunkt Competence Center Home Security...
- Page 23 Whenever you leave and change the alarm mode to arm the lights (PSM-S1, PRM-S2 or smart lights) will turn OFF, the blinds (SCM-S1) will close and the heating system (TRV-S1 or TMST-S1) will be lowered to 18ºC, Blaupunkt Competence Center Home Security...
- Page 24 Every day at 23:00 change the Security system to Home arm, turn all the lights OFF, (PSM-S1, PRM-S2 or smart- lights) close all your blinds (SCM-S1) and turn down the heating system (TRV-S1 or TMST-S1) to 18ºC. Blaupunkt Competence Centre Home Security...
-
Page 25: Live-Video
2.3.1 Video Adjustments. access the video adjustments, click on the icon. On the following submenu would be possible to change video image colours as well as quality (resolution) and the frame rate (FPS). Blaupunkt Competence Centre Home Security... - Page 26 10 seconds before the alarm was triggered and 20 seconds after the alarm to complete the total amount of 30 seconds for the video recording. Blaupunkt Competence Centre Home Security...
- Page 27 To assign or to change the Wi-Fi network of an IP camera click on “Scan Wi-Fi APs”. Select your Wi-Fi network and click “connect”. Then, input the Wi-Fi password o the “Pre-shared Key” field and click “Submit” at the bot- tom. Blaupunkt Competence Centre Home Security...
-
Page 28: Event
All the intrusion alarms such as PIR motion detection, door contact open while arm mode and device tamper will be displayed in red, while system changes or technical alerts as device supervision failure, low battery device or video recordings/photos requested manually will be displayed in yellow. Blaupunkt Competence Centre Home Security... -
Page 29: Settings
If there is any failure on a device (e.g. battery low, tamper open, supervision failure), the device will be highlighted in red and the error will be displayed under the “Fault” column. Door contacts that are open will also be highlighted in red and under the “Status” column will display “DC Open”. Blaupunkt Competence Center Home Security... -
Page 30: Add Device
Step 3 Check the box in front of accessory info and click OK. Step 4 Select the zone (device number) and type a device name. E.g. “DC Front Door”, then Click “OK”. Blaupunkt Competence Centre Home Security... -
Page 31: Update Device List
Hazard accessories as Smoke or Water detectors will still work locally with the in-built siren. Chime: If chime function is enabled the panel will emit a double “beep” sound notification whenever this sensor gets triggered under Home or Disarm mode. Blaupunkt Competence Centre Home Security... - Page 32 Note: If the panic button on the remote control is triggered, the control panel can no longer be dis- armed by the same remote control. This must be done with another device or the app. Blaupunkt Competence Centre Home Security...
-
Page 33: Walk-Test
With the IP camera, the signal is transmitted automatically upon entering Walk Test and does not require to press any button. IP Camera will be displayed always like Blaupunkt Competence Center Home Security... -
Page 34: Panel Setting
• Warning Beep: If a fault is detected in the system and this feature is enabled, the panel will emit a “beep” sound notification (OFF, low, medium, or high volume) every 30 seconds to alert the user of a failure. (Default medium) Blaupunkt Competence Center Home Security... - Page 35 Exit Delay Time expires or they will trigger an alarm. • Exit Delay Sound: Set the Exit Delay countdown volume between OFF, low, medium, or high volume. • Entry Delay Sound: Set the Entry Delay countdown volume between OFF, low, medium, or high volume. Blaupunkt Competence Centre Home Security...
-
Page 36: Panel Settings
• Siren Tamper: By selecting OFF it will disable temporarily the siren’s tamper protection function for one hour. You can also reactivate the siren tamper protection by selecting ON again. This function should be used to avoid a tamper alarm whenever you wish to change the siren location or batteries. Blaupunkt Competence Center Home Security... - Page 37 APN settings manually. Ask your telecom provider for your APN settings: “APN name”, “username” and “password”. At the “RSSI” field check that the GSM signal strength is 6 or above. If the signal is below 6 try another location for the Q-Pro or test with another telecomunications provider. Blaupunkt Competence Centre Home Security...
-
Page 38: Code
User PIN Code slot. • Delete: Check this box to remove this User PIN Code. User 1 cannot be deleted. Click Submit at the bottom to delete the User PIN Code Blaupunkt Competence Centre Home Security... -
Page 39: Time Setting
If you want to keep the accessories that are registered on the panel, make sure to check the “Keep the current network settings” checkbox before clicking submit. Note: The accessories and their settings will be kept, but rules and scenes related to the accessories will still be deleted. Blaupunkt Competence Centre Home Security... -
Page 40: Account
To keep your account secure from hackers we recommend a strong password with at least 8 characters in- cluding lower letters, upper letter, numbers and special symbols. • Account Info: Click icon to access to your account info where the MAC address of the panel and the account number will be displayed. Blaupunkt Competence Centre Home Security... - Page 41 This change will not affect the app language or the panel voice prompt. App language will be set according to the smartphone language. To change the language of the panel voice prompt please refer to chapter 2.5.2.2 Panel Settings Blaupunkt Competence Centre Home Security...
-
Page 42: Notification
Program the Push Notification setting for smartphone devices via Secure4Home App. Click the dropdown menu and select one of the following options: None: No event will be reported All: Alarm and status events will be reported. Burglar: Only alarm events will be reported Blaupunkt Competence Center Home Security... - Page 43 Check the boxes of the e-mail addresses you want to remove at the right end of the e-mail address list and click Submit to remove the selected e-mail addresses from the system. The default e-mail address cannot be deleted. Blaupunkt Competence Center Home Security...
- Page 44 With the premium service, the user will be able to receive telephone calls from Blaupunkt Calling Alarm Centre. Whenever the panel detects an intrusion it will send a report to our Calling Alarm Centre and perform automatically loop calls to your telephone number. Up to 3 different telephone numbers.
-
Page 45: Service & Payment
2.6.3 Service & Payment The Service and Payment page displays the user account service package choices. With the premium service, the user will be able to receive telephone calls from Blaupunkt Calling Alarm Centre. Our premium service call notifications will provide the peace of mind that whenever the panel detects an intrusion it will send a report to our Calling Alarm Centre and perform automatically loop calls to your telephone number. -
Page 46: Operation Of The Mobile App Secure4Home
Activate “Stay logged in” for the app to save your credentials for the next time. After successfully logging in, you will first be redirected to the “Security” page. To switch between the function pages, tap the respective function icons at the bottom. Blaupunkt Competence Center Home Security... -
Page 47: Security
If an accessory has any kind of error the app will display the icon and the number of accessories with an error on the red circle. Tap on the icon to see the issues of the devices. For more information about device errors refer to 3.3 Device. Blaupunkt Competence Centre Home Security... -
Page 48: Device
Device filter: Tap on the button Tap on the button to filter and display only Door Contacts to filter and display only accessories with Open status. with any kind of error. Blaupunkt Competence Centre Home Security... -
Page 49: Home Automation
By clicking on the scene it’s possible to check the actions of that scene. NOTE: Scenes cannot be created, edited or deleted on the app. For those features please use the Home Portal interface. For more information refer to chapter 2.2.4 Scene. Blaupunkt Competence Center Home Security... - Page 50 Then select the accessory from the accessory list and tap “Delete”. • To add accessories to a room, select the desired room and click icon top right corner. Then select the accessory from the accessory list and tap “Add”. Blaupunkt Competence Centre Home Security...
- Page 51 Then select the accessory from the accessory list and tap “Delete”. • To add accessories to a group, select the desired group and click icon. Then select the accessory from the accessory list and tap “Add”. Blaupunkt Competence Centre Home Security...
- Page 52 Tap on the desired rule to see the rule trigger, condition and actions. NOTE: Rules cannot be created, edited or deleted on the app. For those features please use the Home Portal interface. For more information refer to chapter 2.2.5 Rule Blaupunkt Competence Centre Home Security...
-
Page 53: Camera
In this submenu, you can manage the motion detector with camera (IRC-S2 and IRC-P4). Click the icon to take a photo with the IRC camera. The photo will be loaded to the Home Portal and displayed on the Event menu. Blaupunkt Competence Center Home Security... -
Page 54: Event
/ photos requested manually will be displayed in yellow Press an event for details as Date, Time, and accessory triggered. Additionally, events captured by the IRC-S2 or IRC-P4 will display the captured photo. Blaupunkt Competence Centre Home Security... -
Page 55: Account
Alarm type push notification. Any other push notification uses the standard notification tone from your phone and won’t disturb you if the phone is on silence mode. Blaupunkt Competence Center Home Security... - Page 56 Mode change will not work. For more information, see the Home Connect Server Manual. For configuration of the Arm Home Mode, see chapter 2.6.1 Device Setting in the Home Connect Server Manual (Download at service.blaupunkt-security.com). Blaupunkt Competence Centre Home Security...
- Page 57 ID account num- ber, the region assigned for your panel and account and the version of the Secure4Home app. At the bottom can be found the Blaupunkt Technical support contact Info according to your app language and country.
-
Page 58: Troubleshooting And Reset To Default Settings
Check on the device menu for any accessory with tamper error. Refer to the accessory manual to locate the tamper and check if it’s properly pressed. • Radio interference: Perform Walk Test on all your accessories to check if Q-Hub can still receive their signals. Blaupunkt Competence Center Home Security... -
Page 59: Motion Detector
• Reconnect the power plug while holding down the red button on the back. • Press the button for about 5 seconds until the alarm panel emits a long beep and all 3 LEDs light up. • Release the button: the factory reset is complete. Blaupunkt Competence Centre Home Security... - Page 60 Enjoy it. BLAUPUNKT Competence Centre Security Security Brand Pro GmbH Mondstrasse 2-4 85622 Feldkirchen-München, Germany © Technical changes and errors excepted...
Need help?
Do you have a question about the Q Series and is the answer not in the manual?
Questions and answers