Ricoh FT6655 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Ricoh Manuals
  4. All in One Printer
  5. FT6655
  6. Operating instructions manual
Ricoh FT6655 Operating Instructions Manual

Ricoh FT6655 Operating Instructions Manual

Ricoh all in one printer user manual
Hide thumbs Also See for FT6655:
Table of Contents

Advertisement

Quick Links

Download this manual
Iumml
/
FT6645/6655
Operating
Instructions
'\
'k

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT6655 and is the answer not in the manual?

Questions and answers

Related Manuals for Ricoh FT6655

Summary of Contents for Ricoh FT6655

  • Page 1 Iumml FT6645/6655 Operating Instructions ‘\ ‘k...
  • Page 2 Note: Certain options contact your local Ricoh shall not be responsible of parts other than genuine Ricoh parts in your Ricoh office product. I For good copy quality, Ricoh recommends ~ower source: 120V, 60 Hz, more than 20A ‘lease make sure to connect the power cord to a power source about Dower cord.

  • Page 3: Safety Information

    When using your copier, the following Safety During Operation In this manual, all safety messages These words mean the following: WARNING: Important information to alert you to a situation damage to your property if instructions Caution: Impotiant information that tells how to prevent situation that might cause minor injury.

  • Page 4: General Safety Information

    SAFETY INFORMATION General Safety Information ~ &lways turn the copier off when you have finished copying for the day, but leave it plugged D When the copier will not be used for a long period, disconnect the power cord. Cl If the copier must be transported by vehicle, please contact your service representative.

  • Page 5: Installation Requirements

    Copier Environment INSTALLATION Copier Environment The installation location should be carefully chosen because environmental affect the performance of a copier. - Optimum environment tJ Temperature: 10- 30”C (50 - 86°F) Cl Humidity: 15- 90?40 D A strong and level base. 0 The copier must be level within 5 mm (0.2”) both front to rear and left to right.

  • Page 6: Power Connection

    INSTALIJ4TION REQUIREMENTS Power Connection Avoid multiwiring. Cl Make sure that the wall outlet is near the copier and easily accessible. D Make sure the plug is firmly inserted ~ Voltage must not fluctuate more than 10YO. Cl Do not set anything on the power cord.

  • Page 7: Paper Storage

    Storage Supplies Paper Storage Paper should always be stored properly, reproduction, creased copies, and paper misfeeds. ~ Avoid storing paper in humid areas. (Under high temperature store copy paper in a vinyl bag,) Z1Do not store paper where it will be exposed U Store on a flat surface.

  • Page 8: Table Of Contents

    TABLE OF CONTENTS GUIDE TO COMPONENTS Copier Type ... . . Copier Exterior ... . System Overview ... Operation Panel Key Tops...
  • Page 9 SEITING ORIGINALS IN THE RECIRCULATING Recommended Originals Non-recommended Originals Setting Originals ... SETTING ORIGINALS ON THE EXPOSURE BASIC FUNCTIONS AND KEY TOPS sort , .,...0.0.000. Stack ....Stapling Gopies.
  • Page 10 TABLE OF CONTENTS SPECIFICATIONS Copier ..Dual Job Feeder ..Compact Sorter Stapler Floor Type Sorter Stapler Recirculating Document Finisher ... . . 3,500-sheet Large Capacity COMBINATION...
  • Page 11 Before reading this Operating Instructions, please refer to pages 2-5 to know which type of copier and system you have.

  • Page 12: Guide To Components

    GUIDE TO COMPONENTS Copier Type There are two types of copier. Type Type ~-.--.--! GUIDE TO COMPONENTS Three 550-sheet paper trays Optional 3,500-sheet —-—— ---- (3,500) .—— — ——— Tandem paper tray (two 500-sheet paper trays) One 550-sheet paper tray 1,500-sheet large capacity Optional...

  • Page 13: Copier Exterior

    Copier Exterior Copier Exterior TRAY (Option) COPY MAIN SWITCH Completed copies are Switches delivered here. ON and *FOR TYPE 2 55CKWEET This tray can sheets of paper. Ep J \ “FOR TYPE 550-SHEET PAPER TRAYS These trays can hold 550 sheets of copy paper each.

  • Page 14: System Overview

    System Overview System A (Copier type 1 with dual job feeder and compact Compact sorter stapler— System B (Copier type 1, or 2 with dual job feeder and floor type sorter stapler) “Illustration shows type 2. Floor type sorter stapler sorter stapler) Dual job feeder Dual job feeder...
  • Page 15 System C (Copier type 2 with recirculating Finisher document handler and finisher) Recirculating document handler i-f== 3,500-sheet – large capacity tray...

  • Page 16: Operation Panel

    GUIDE TO COMPONENTS Operation Panel Tops GUIDANCE Press to see guidance for functions. > See page 12. CONTRAST DIAL You can change the brightness of the display. Program ~ -> NUMBER PROGRAM ~EY Use to enter the Press to select the desired number of program mode,...

  • Page 17: Touch Panel Display

    Touch Panel Display Initial Display System A and B System Keys that have the option of being selected. Keys that have been selected. Keys that have no option to select. GUIDE TO COMPONENTS COPY COUNTER Indicates the number of copies. BASIC FUNCTIONS AND KEY TOPS See page 35.

  • Page 18: What You Can Do With This Copier

    WHAT YOU CAN DO WITH THIS COPIER WHAT YOU CAN DO WITH THIS COPIER System A and B Ready 1“ 81/2x 8’/2X 11X17G & 8V2X 1 1 U .Bwass Tray Auto CC ~ erfSlip Shyt] ( Edit Imagq ) f page 9.
  • Page 19 WHAT YOU CAN DO WITH THIS COPIER (“) See pages 60-63. ~hmt hwrl lPaper Ilesignatel ., . . . @i@@fl . “, . . .,,:.., ..,.,.,.,:.,... ,.:,,, , ,,,. . .,. “456 IN’ Y ip $ hod 1...”...
  • Page 20 CAN DO WITH THIS COPIER WHAT YOU (“” Editing/ Centwing !hve Area I Mete El p (i-e’ l%se’t See pages 56-59. Erm Borderl Bord. I Cent. / page hull IEm!!LJ...
  • Page 21 Dupbl I rl : ~: ,--.-’, Kl%l Emml ,’,:& =’;-., WHAT YOU CAN DO WITH THIS COPIER See pages 44-55. Combine I hnbine2 Nkn. I I Combine 4 Min. I...

  • Page 22: How To See The Guidance Display

    TO SEE THE GUIDANCE DISPLAY HOW TO SEE THE GUIDANCE Press the Guidance key when you want to know detailed use. You can use this key in stand-by Seeking Guidance In Stand-by Press the Clear Modes key and the Guidance key, Touch the key you want to know about on the touch panel display.

  • Page 23: Seeking Guidance While Entering Job Settings

    Seeking Guidance While Entering Job Settings Seeking Guidance 1. Press the Guidance key. The information about have selected just before will be dis- played on the touch panel display. example, if you have Staple mode, the guidance shown at right. Cl The touch panel display shown at right is for system B.

  • Page 24: User Tools

    CHANGING DEFAULT SE7TINGS CHANGING User Tools This section is for the key operators copier’s default settings using the following User Tools Menu < User Tools> < User Tools> Selectone of the followingItems. Selectone of the folloiulng i tems. Auto rwet/Auto ~Select specialtray ~Set...

  • Page 25: Autoreset/Auto Off

    User Tools Auto reset/Auto The co ier returns to its initial condition our jo Auto reset rom 1 second to 999 seconds, off . ~ default: When the machine the selected Screen Saver automatically. seconds, ~ default: When the copier is used after the weekly timer has turned it off, the copier will turn itself back off after the selected Auto The auto off time can be set from 1 minute to 999 minutes,...

  • Page 26: Weekly Timer

    CHANGING DEFAULT SEITINGS Use to set the copier’s internal clock before setting the weekly timer. the touch panel display instructions. necessary, remember to adjust the clock time. Weekly Timer Use to set the weekly timer. If you set the timer, the copier turns on and off automatically the selected time each day.

  • Page 27: Tray Display

    User Tools Change fixed R/E has 10 fixed ratios (4 enlargements This copier fixed reproduction ratios to different Set standard tray display When Auto Paper Select is canceled, as a default setting. Paper Tray Priority the other tray as a default setting. As a default setting, the Auto Paper Select is selected.

  • Page 28: Copy Count

    CHANGING DEFAULT SETTINGS User Tools for User Code Mode If the copier is set to use the User Code function, codes before the machine can operate. copies made under each user code. mode, please contact your sales or service User tools 8,9, 10 and 11 are for the User Code mode.

  • Page 29: Setting Originals In The Dual Job Feeder

    Remmmended Originals SETTING ORIGINALS Recommended Originals For this dual job feeder, the following 41-52 Paper Weight 11 -131b Maximum number of originals to be set A3 lengthwise A4 lengthwise A4 sideways A5 sideways b a) > B4 lengthwise B5 lengthwise <...

  • Page 30: Non-Recommended Originals

    SEITING ORIGINALS IN THE DUAL JOB FEEDER Non-recommended Caution: The following types of originals feeder. Please place them directly on the exposure than 128 g/rep, 34 lb Originals thicker Originals thinner than 41 g/rep, 11 lb Paper with any kind of coating (such as carbon) on the back, or originals that are taped together Originals smaller than A5 sideways, 5112”x 8112”...

  • Page 31: Setting A Stack Of Originals

    Setting A Stack Of Originals Setting A Stack Of Originals Automatic Document Feed (ADF) mode Automatic Reverse Document Sided Originals mode) In this mode, the operator inserts a stack of originals These originals are individually fed onto and removed Correct any curl, fold, or crease in the originals before...
  • Page 32 originals face up into Insert Original feeder until dicator goes off. The original guide must touch the front side of the originals. Do not stack originals above the limit mark. Press the Start key, The bottom sheet of the original stack (last page) is fed into the dual job feeder first.

  • Page 33: Setting One Original At Atime

    Setting One Original At A Time Setting One Original Semi-Automatic Document mode, the operator inserts one original at a time into the dual job feeder. In thk automatically fed onto and removed from the exposure glass. any curl, fold, Correct or crease in the originals before setting.
  • Page 34 SEITING ORIGINALS IN THE DUAL JOB FEEDER the original face into the dual job feeder until the Insert indicator goes off. Start with the last page of the originals. The original guide must touch the front side of the original. Press Start key.

  • Page 35: Setting Different Sized Originals

    Setting Different Sized Originals Setting Diffe Sized Originals mode Mixed Sized In this mode, you can set originals feeder. You can use the following A4/A3 version: A3, B4, A4 and B5 11” x 17”, 81/2” x 14”, and 81iz” x 11“ LT/DLT version: Touch the Special...
  • Page 36 SEITING ORIGINALS IN THE DUAL JOB FEEDER Adjust the original guide to match the widest original. Set the originals face up into the dual feeder until the insert indicator goes off. Cl Originals must be aligned to the rear-left corner of the dual job feeder, as shown.

  • Page 37: Setting A Pasted Original

    Setting A Pasted Original Setting A Pasted Original Pasted Original mode In this mode, you can set a pasted original you can set one original at a time. o In this mode, Touch the Special Orig. touch panel display. (See page 41.) Touch the Pasted Original touch panel display.
  • Page 38 SETTING ORIGINALS IN THE DUAL JOB FEEDER one pasted original face dual job feeder until the Insert Original indicator goes off. Start with the last page of originals. Cl The original guide must touch the front side of the original. Start Press key.

  • Page 39: Presetting Originals During A Copy Run

    Presetting Originals During A Copy Run Presetting Originals Touch the Preset key of the touch panel display. (See page 41.) Following the instructions on the dis- play, set the copy job settings for your next job. Touch the Exit key of the touch panel display.
  • Page 40 SETTING ORIGINALS IN THE DUAL JOB FEEDER Touch the Exit key of the touch panel display. After your first job is finished, the next will start automatically. Cl When presetting a job using the compact sorter stapler, you have to remove the current job’s copies from the sorter stapler before the preset job can start.

  • Page 41: Recommended Originals

    SEITING Recommended Originals SETTING ORIGINALS RECIRCULATING Recommended Originals For this recirculating document handler, the following 52-103 SIZE A3 lengthwise o ,- F (8” x 13“) lengthwise > A4 sideways A4 lengthwise A5 lengthwise 11” x 17“ lengthwise 81/2”x 14 lengthwise 11”...

  • Page 42: Non-Recommended Originals

    SETTING ORIGINALS IN THE RECIRCULATING Non-recommended Caution: The following types of origins/s ing document handler. Please place them directly on the exposure O Originals thicker than 128 g/m2, 34 lb D Originals thinner than 52 g/rep, 14 lb D Paper with any kind of coating (such as carbon) on the back, or originals that are taped together D Originals smaller than A5 lengthwise, 51/2”...
  • Page 43 SETTING ORIGINALS IN THE RECIRCUIJ+TING DOCUMENT HANDLER Setting Originals Adjust original guides original width. If you have more than two originals, square the stack of originals. originals face up in the original stacker. The Set Original indicator should turn off. Originals should be the same size.

  • Page 44: On The Exposure Glass

    SEl17NG ORIGINALS ON THE EXPOSURE GIASS SETTING ORIGINALS If your machine is equipped with the platen Lift the platen cover. Set the original face down on the ex- posure glass. The original aligned to the rear left corner. Before pressing the Start key, lower platen cover.

  • Page 45: Basic Functions And Key Tops

    BASIC FUNCTIONS AND KEY TOPS I ,:, ::.=:: , .:x,:x -Want’ouseo IEEiil The copier automatically controls ing to the original background density. After canceling the Auto Image Density, adjust the image density manually. touch the right keys. To get a lighter image, touch the left keys.

  • Page 46: And Key Tops

    BASIC FUNCTIONS AND KEY TOPS When you have selected key appears see at a glance all the modes you selected. After the Check Modes key is touched, P!zJ the touch panel display. play when the Check Modes key was touched. When you select functions appears change settings...

  • Page 47: And Key Tops

    sort Before using the Sort function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. System A and B copy of each original is System the Sort key.

  • Page 48: And Key Tops

    BASIC FUNCTIONS AND KEY TOPS EEDm! Before using the Stack function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. System A and B All copies of each original are delivered System Copies from different copy runs are grouped...
  • Page 49 Stapling Copies Stapling Copies ‘ Before using the Staple function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. the Staple function, groups of D If you select this function, the Sort function is automatically selected. Stapling Position and Original...
  • Page 50 BASIC FUNCTIONS AND KEY TOPS rl Forthe Staple function, the following limitations apply: Maximum paper A3,11’’x17” size Minimum paper B5, 8112°x 11” size Maximum paper 80 g/mz, 20 lb weight Minimum paper 52 g/m2, 14 lb weight A4, 81/2” x 11” or smaller: from 2 to 20 sheets Stapler capacity B4, 8112°x 14“...
  • Page 51 This key can be used only when you have system You can staple copies sorted in bins after copying (This key has two functions. This key can be used only when your machine DiEEiEl This key can be used only when your machine You can set the copy settings for your next job.

  • Page 52: Auto Start Mode

    BASIC FUNCTIONS AND KEY TOPS t> Program You can store up to 5 frequently for future use. can select the Program N0,5 as a default setting using Entering a program Set the copy settings you want to put into memory. Press the Program Follow the instructions Recalling...

  • Page 53: Functions On Operation Screens

    Reduce/Enlarge FUNCTIONS ON OPERATION FUNCTIONS ON OPERATION SCREENS SCREENS You can select one of 10 preset ratios. enlargement 6 reduction ratios and 4 ratios are preset. O You can change the fixed ratios using User Tool 6. See page 17. The reproduction ratio can be changed from 50% to 200?10in 10/0steps.

  • Page 54: Duplex/Series Copies (Duplex)

    FUNCTIONS ON OPERATION SCREENS Before using this function, please refer to page 4 and 5 to know which system function is different depending on the system O A right margin (5 mm, on the back side automatically. 0.2”) is set System A and B If your machine is equipped with the dual job feeder (system A or B), you should select one of three keys (Autocount, Even, or Odd)
  • Page 55 Duplex/Series Copies (Duplex) this Select key if the number of originals if the number of originals Select this key 432’ FUNCTIONS ON OPERATION SCREENS is even. is odd. Wnen you set originals feeder, last should be on the bottom as shown, in the dual job page of originals...
  • Page 56 FUNCTIONS ON OPERATION SCREENS System C your machine is equipped with the recirculating document handler (system C), the Autocount function is default. Do the following. Set the stack of originals Start key. Press the The machine starts counting start automatically. lJN!wLl Duplex/Series Copies (Duplex~ face up in the recirculating...
  • Page 57 Duplex/Series Copies (Duplex) mmml This function makes 2 sided copies from 2 sided originals. FUNCTIONS ON OPERATION SCREENS When you set originals in the dual job feeder, the last page of the originals should be on the bottom as shown. in the recir- When originals...

  • Page 58: Copies (Series Duplex)

    FUNCTIONS ON OPERATION SCREENS be used if copy paper larger than A4 sideways or The following functions cannot selected. The center of an original is determined according to the selected copy paper and sure to select copy paper and reproduction ratio suitable for the original. This function makes 2 sided copies from 2 facing pages of a bound (book) original.

  • Page 59: Duplex/Series Copies (Series Duplex)

    Duplex/Series Copies (Series Duplex) Use this function to have the copies face each other exactly do. When you use this function, place the original on the exposure For bound originals read from left to right, place the original cover right side up. You should start with the last page of the originals should be aligned to the left scale as shown.

  • Page 60: Duplex/Series Copies (Series Copies)

    FUNCTIONS ON OPERATION SCREENS Book+l$iM 2$idod + I$idod This function makes 1 sided copies from two facing pages of bound (book) originals. Cl This function cannot be used if copy paper larger than A4 sideways or 81/2” x 11” sideways is selected. O The center of an original is determined according to the selected copy paper and reproduction sure to select copy paper and reproduction ratio suitable for the original.
  • Page 61 LJlll ’234 When you set originals in the dual job feeder, the last page of the originals should be on the bottom as shown. When you set originals in the recir- culating document handler, page of the originals should be on the bottom as shown.

  • Page 62: Duplex/Series Copies (Combine)

    FUNCTIONS ON OPERATION SCREENS Combine2 Origs. Combine4 Orixs. The Combine function can be used only when your machine is equipped with the dual job feeder (system - A or B). Cl When using the Combine functions, please select the copy paper size below. A4/A3 version: A4 sideways, B5 sideways, A5 sideways LT/DLT version:...
  • Page 63 Duplex/Series Copies (Combine) Select this key if the number of originals FUNCTIONS ON OPERATION SCREENS is even. When you set originals feeder, the last page of should be on the bottom in the dual job the originals as shown.
  • Page 64 ON OPERATION SCREENS FUNCTIONS Select this key if the number of originals Duplex/Series Copies (Combine) is odd. When you set originals feeder, the last page of the originals should be on the bottom as shown, in the dual job...
  • Page 65 Duplex/Series Copies (Combine) This function makes one 2 sided copy from four 1 sided originals. O After selecting the Combine 4 Origs. function, you have input the number of originals. FUNCTIONS ON OPERATION SCREENS to select the Autocount key or Number keys key to Example: Number When...
  • Page 66 When making copies in the Editing/Centering or the recirculating document O In the Save Area and the Delete Area modes, the designated line will vary by f5 mm ( + 0.2”). Therefore, leave at least 5 mm (0.2”) between the designated line and the image. If this clearance is narrower than this, undesired image portions might be deleted or saved.

  • Page 67: Edit Image(Editing/Centering)

    Edit Image(Editing/Centering] FUNCTIONS ON OPERATION SCREENS This function centers original image on the copy.

  • Page 68: Edit Image (Margin Adj.)

    Edit Image (Margin Adj.) You can make margins by shifting the image to the left or right, and towards the top or bottom. This function is convenient when binding copies. o A41A3 version Maximum margin width: Left and right: Top and bottom: Cl LT/DLT version Maximum margin width: Left and right: Top and bottom:...

  • Page 69: Cover Mode

    FUNCTIONS ON OPERATION SCREENS Cover mode The Front Cover function can be used only when your machine tem A or or the recirculating document Cl ~5hen using the Front Cover function, you should set the tray for cover sheets using User Tool 2. See page Cl You can also select the bypass feed tray for cover sheets.
  • Page 70 The Fron~Back Covers function can be used only when your machi~e feeder (system or B), or the recirculating ~ When using the Front/Back Covers function, you should set the tray for cover sheets using User Tool 2. See page 15. can also select the bypass feed tray for cover sheets.
  • Page 71 FUNCTIONS ON OPERATION SCREENS The Paper Designate function can be used only when your machine (system A or B), or the recirculating document Before using this function, please refer to pages function is different depending on the system System A and B (with dual job feeder) After selecting this function,...

  • Page 72: Cover/Slip Sheet (Ohp Slip Sheet)

    Cover/Slip Sheet (OHP Slip Sheet) o ~5hen using the OHP slip sheet function, you should set the tray for slip sheets using User Tool 2. See page o You can also select the bypass feed tray for slip sheets. In this case, make sure to set paper for slip sheets that are identical in size and direction with the paper to which you are copying, because the machine cannot detect the length of paper set in the bypass feed tray.

  • Page 73: Loading Paper

    LOADING PAPER The following paper sizes can be set. Copier type 1 Paper Size Ilnxli’” 81/zm X14” 81/2’xll” 81t2n X 13“ tF41 8“ x 101/2” 8“x1O” 8“X13’’ (F) 1!?n f?flAn Copier type 2 Tandem Paper Tray (~~s:hwesor x 2 sets) Paper Size 11”X17”...
  • Page 74 “L” means lengthwise. “S” means sideways. version machines. O can be used for A4A3 can be used for LT/DLT version machines. O*: 2 sets of 500 sheets can be set in A4/A3 version machines. sheets can be set in *: 2 sets of 500 LT/DLT version machines.

  • Page 75: 550-Sheet Paper Tray

    LOADING PAPER 550-sheet Paper Tray OForcopiertypel (lst,2nd and3rd feed station) For copier type 2 (2nd feed station) Cl You can change the paper size of the 2nd feed station. See page 73. Pull out the paper tray until it stops. Load paper in the paper tray.

  • Page 76: Tandem Paper Tray

    Tandem Paper Tray Tandem Paper Tray IJ For copier type 2 (1st feed station) Cl Before loading paper inthetandem Was the whole tray pulled out or only the left part? The whole tray was pulled out. Follow the Follow the procedure on procedure below.
  • Page 77 LOADING PAPER Load paper in the right paper tray. The paper stack must be flush with the right side of the paper tray. Do not stack paper over the limit mark, Make sure to read the notice on the pack- age showing the front side (copy side) of the paper.

  • Page 78: 1,500-Sheet Large Capacity Tray

    1,500-sheet Large Capacity Tray 1,500-sheet Large Capacity o For copier type 2 (3rd feed station) Press the Down key to lower the bot- template. The Down keystarts ing. paper has run out, the bottom plate lowers automatically and the lit. In this case, you need not press the Down key.

  • Page 79: Optional 3,500-Sheet Large Capacity Tray

    LOADING PAPER Push the tray until it stops. Optional 3,500-sheet Open the cover of the large capacity tray. When opening the cover, hold it by the lip. Press the Down key to lower the bot- tom plate. The Down key starts blink- ing.

  • Page 80: Bypass Feed Tray

    Bypass Feed Tray Repeat steps 2 and 3. Close the cover. Bypass Feed Tray 1. Open the bypass feed tray. Slide the paper guides to the paper width. If you use copy paper larger than A4 sideways or 8112° x 11” sideways, out the paper support guide.
  • Page 81 LOADING PAPER Insert the copy paper. Make sure to read the notice on the pack- age showing the front side (copy side) of the paper. Load paper with the mpy side After copying is completed, bypass feed tray. close the...

  • Page 82: Changing Paper Size

    o You can change the pa~~ size of the 2nd tray. contact your sales or serwce representative. 1. Pull out the 2nd paper tray stops. Remove copy paper. While pressing the release lever on the front side guide, slide the front and rear guides to the paper size you want to use.

  • Page 83: Size

    Select the paper size by adjusting paper size selector on the back side of the tray. Load paper. Cl The paper stack must be flush with the right side of the tray. Do not stack paper over the limit mark. Make sure to read the notice on the pack- age showing the front side (copy side) of the paper.

  • Page 84: What To Do When Things Go Wrong

    WHAT TO DO WHEN THINGS GO WRONG Problem Nothing happens when the main switch IS turned on. The Start key does not change from red to green after the main switch is turned on? or the machine stops during a copy run. Problem Image density Copies appear...

  • Page 85: User Remarks

    USER REMARKS Problem Staples do not come out at You loaded the new staple all. cartridge. There are “ammed staples in the stap er. O If you cannot correct the problem by taking the actions above, please contact your service representative. Cl Narrow margins at the leading and side edges of original are not copied.

  • Page 86: When Removing Misfed Paper

    WHEN ADDING TONER WARNING: Do not incinerate when exposed [ WARNING: Dispose of the used toner Cl When adding toner, follow the instructions IJ Do not turn off the main switch. WHEN REMOVING MISFED PAPER WARNING: Since some parts voltage, touch machine door.

  • Page 87: Copier

    DAILY MAINTENANCE To maintain high copy quality, clean the following Copier Touch Panel Display Clean the touch panel display cloth. SOft Exposure Glass Lift the platen cover, dual job feeder or recirculating document handler. Clean the exposure glass with a damp cloth and wipe it with a dry cloth.

  • Page 88: Dual Job Feeder

    Dual Job Feeder Dual Job Feeder Belt Lift the dual job feeder. Clean the belt with adamp wipe it with a dry cloth. If stains do not come off, use belt cleaner. Feed-in Unit Clean the original table and original guide with a damp cloth and wipe them with a dry cloth.

  • Page 89: Recirculating Document Handler

    DAILY MAINTENANCE Recirculating Document Belt Lift the recirculating document ler. Clean the belt with a damp cloth and wipe it with a dry cloth. If stains do not come off, use belt cleaner. Feed-in Unit Clean the original stacker and original guides with a damp cloth...

  • Page 90: Specifications

    Copier Copier Console Configuration: Process: Dry electrostatic Originals: Sheet, book Maximum: Original Size: Copy Paper Size: See pages 64 and 65. Copy Paper Weight: Paper tray: Bypass feed tray: Duplex copying: See pages 64 and 65. Copy Paper Capacity: Copying Speed: Type 1: Type 2:...

  • Page 91: Large Capacity Tray

    SPECIFICATIONS Reproduction Ratio: Power Consumption: Type 1 and 2 Full system: Copier with dual job feeder, compact sorter stapler, and 3,500-sheet large capacity tray Copier with dual job feeder, floor type sorter stapler, and 3,500-sheet large capacity tray Copier with recirculating document handler, finisher, and 3,500-sheet large capacity tray A4/A3version 65’ZO...
  • Page 92 Copier Type 1 and 2 Noise Emission Sound pressure level: The measurements are made according to 1s07779. Full system: Copier with dual job feeder, capacity tray Copier with dual job feeder, large capacity tray Copier with recirculating document handler, finisher and 3,500-sheet large capacity tray Dimensions (W x D x H):...

  • Page 93: Dual Job Feeder

    SPECIFICATIONS Weight: Type 1 Copier Copier with dual job feeder, compact sorter stapler, 3,500-sheet large capacity tray Copier with dual job feeder, floor type soder stapler, 3,500-sheet large capacity tray Type Copier Copier with dual job feeder, floor type sorter stapler, 3,500-sheet large capacity tray Copier with recirculating document handler, finisher, 3,500- sheet large capacity tray Optional Equipment:...
  • Page 94 Dual Job Feeder Dual Job Feeder Original Size: See page 19. Original Weight: See page 19, See page 19. Original Table Capacity: Original Feed: Automatic Automatic Semi-automatic Mixed sized mode Pasted original Preset mode Face up, first sheet on top Original Set: One flat belt...
  • Page 95 SPECIFICATIONS Compact Sorter Stapler Paper Size for Bins: Paper Weight for Bins: Bin Capacity: Number of Bins: Stapler Capacity: Stapling Position: Staple Replenishment: Power Source: Power Consumption: Dimensions (W x D x H) Weight: See pages 37 and 38. See pages 37 and 38. See pages 37 and 38.

  • Page 96: Floor Type Sorter Stapler

    Floor Type Sorter Stapler Floor Type Sorter Stapler Paper for Proof Tray: Paper for Bins: Paper Capacity: Stapler Capacity: Staple Position: a.6f3mm a=6*3mm b=6*3mm b=6*3mm e=45t5e Staple Replenishment: Power Source: Power Consumption: Weight: Dimensions (W x D x H) Size: Maximum: A3,11’’x Minimum:...

  • Page 97: Recirculating Document Handler

    SPECIFICATIONS Recirculating Document Original Size: See page 31. Original Weight: See page 31. Number of Originals See page 31. to be Set: Original Feed: RDH mode (1 sided original Original Set: Face up, first sheet on top Original Transport: One flat belt DC 24V (from copier) Power Source:...

  • Page 98: Finisher

    Finisher Finisher Paper Size: Sort (default) When the shift tray is not shifted, A6 can be stacked. Stack Staple Sort (default) Paper Weight: Stack mode: Staple mode: Paper Capacity: Sort (default) Stack mode: Staple mode: .—. Posltlon: Staple Staple Bottom Staple a=6?3mm b=6f3mm...

  • Page 99: 3,500-Sheet Large Capacity Tray

    SPECIFICATIONS 3,500-sheet Large Capacity Copy Paper Size: Copy Paper Weight: Power Source: Power Consumption: Dimensions (W x D x H): Weight: Cl Specifications are subject to change without Tray See pages 64 and 65. 64-105 g/mz,16-241b DC 24V, 5V (from copier) 40 w 403 x 529 x 608 mm...

  • Page 101: Combination Chart

    COMBINATION CHART This combination chart shows which modes can be used toqether. O means that these modes can be used tdgether. means that one of these modes will be selected automatically. X means that these modes cannot be used together. Save Area Delete Area Erase Border...
  • Page 102 Duplex/Series Copies ~ Finishing , 14 18 ‘ 19 01 0 ’ o x’ o’ ~ x ‘~J o~x~ ETC. Cover/Slip Sheet 25!26~ 28129130131132 010( o~o!o 0101 0!0!0 o~ol a~x!o o’ 0!01 010: ‘o o~o~ olo~ 010’ Olxl Ojx! :>;x~o x I Xix’o x ix x ‘x...
  • Page 103 INDEX Access To Copier, iv Accessing user tools, 14 ADF mode, 21 ARDF mode, 21 Auto Image Density key, 35 Auto Off, 15 Auto Paper Select, 17 Auto Paper Select key, 35 Auto Paper Select Priority, 17 Auto Reduce/Enlarge key, 35 Auto reset, 15 Auto reset/Auto off Auto Off, ~5...

  • Page 104: Guide To Components

    Feed-in Unit, 79-80 Finisher, 5, 89 Floor type sorter stapler, 4,87 from 1 sided originals to 2 sided copy, 11 from 2 sided original to 1 sided copies, 11 from 2 sided original to 2 sided copy, 11 from book original to 1 sided copies, 11 Front Cover key, 9, 60 Front doors, 3...

  • Page 105: Storage Of Supplies

    Original Count Display, 17 Thin Paper mode, 17 Select special tray Tray Display for Cover Sheet, 15 Tray Display for Slip Sheet, 15 Tray for Cover Sheet, 15 Tray for Slip Sheet, 15 Select Tray key, 35 Semi-Automatic Document Feed mode, 23 Series Copies key, 11, 50 2 Sided ~ 1 Sided key, 11, 51 Book -1...
  • Page 106 (TEL)490-09-60 Italy RICOHITALIA S.P.A. Via dells Metallurgic, 12 (zona Basson) -37139 VERONA (TEL)045-8510044 Tree Crescent, Feltham, _lVVl3 7HG Hong Kong RICOH BUSINESS MACHINES, LTD. 23/F., China Overseas Building, 139, Hennessy Road, Wan Chai, Hong (TEL) 862-2888 uses, and with the...
  • Page 107 RICOH COMPANY, LTD. Address : 15-1, 1 chome, Minami-Aoyama, Minato-ku, Tokyo Telephone : Tokyo 3479-3111 242-5415,242-5418 Telex : “RICOHBLDG TOKYO” Cable : Printed in Japan A0968607...

This manual is also suitable for:

Ft6645

Table of Contents