Related Manuals for Renesas R8C/15
Summary of Contents for Renesas R8C/15
- Page 1 REJ10J0746-0110 R8C/15, R8C/17 StarterKit Tutorial RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / R8C/Tiny SERIES Rev.1.10 Renesas Solutions Corp. Revision date : Mar 01, 2005 www.renesas.com...
- Page 2 (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corporation product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation or a third party.
- Page 3 Table of Contents accessory softwares to install Until a sample program is operated with an emulator software 2.1 Flash programmer (Flash development toolkit) Installation 2.2 Emulator Software, C Compiler and High-performance Embedded Workshop Installations 2.3 USB driver installation 2.4 Operate Sample Program...
- Page 4 1. accessory softwares to install 1) Note the following points before installing. a) The M3T-NC8C has already been installed. b) The M3T-NC30WA has already been installed. c) The emulator software has already been installed. Install the software attached to this product after uninstalling the above software. 2) The directory and file names including space cannot be used.
- Page 5 Click “OK”. Click “Next” Select language to be used and click "Next"...
- Page 6 Only when you agree with License Agreement, click "Yes". Click “Next”. Click “Next”.
- Page 7 Remove a check. Click “Next” Click “Next”. Refer to a new folder name, or select from the existing folder list and Click “Next”.
- Page 8 Refer to a new folder name, or select from the existing folder list and Click “Next”. Click “Next”. Click “Install”.
- Page 9 Click “finish”.
- Page 10 2.2 Emulator Software, C Compiler and High-performance Embedded Workshop Installations 1) Installation Double-click an installer of CD-ROM ¥ dlp_tool ¥. 2) Installation procedures are described below. Select the language to be used and click “Next”. Click “Next”...
- Page 11 Only when you agree with License Agreement, click "Yes". Select all and click “Next” Refer to a new folder name, or select from the existing folder list and click “Next”.
- Page 12 Refer to a new folder name, or select from the existing folder list and click “Next”. Click “Yes” Check the setting before starting the installation and if the setting is correct, click “Next”.
- Page 13 Check the setting before starting the installation and if the setting is correct, click “Next”. Then, a copy will be started. Click “Finish”.
-
Page 14: Usb Driver Installation
2.3 USB driver installation Connect the E8 emulator using the USB cable to the USB port of host machine. <Windows XP> Installation procedures are described below. If the E8 emulator is connected, it is recognized as a new hardware. Click “Next” after selecting “Install the software automatically”. Click “Continue”. - Page 15 Renesas USB drivers are not authenticated by Microsoft, but we provide them based on the sufficient examination. Insert CD-ROM and specify ¥dlp_tool¥DRIVERS¥USB¥XP¥. Click “OK”. Click “Finish”. The installation is completed above.
- Page 16 <Windows 98/ME> Installation procedures are described below. If E8 emulator is connected, it is recognized as a new hardware. Click “Next” and start installing a driver. Put a check into “search for the best driver for your device” and click “Next”. Insert CD-ROM and Put a check into “Specify a location”.
- Page 17 Click “Next”. Click “Finish”. The installation is completed above.
- Page 18 2.4 Operate Sample Program 1) Copy ¥Japanese¥M3A0115_17¥PROGRAM¥ in CD-ROM to the given folder. 2) Change a file attribute Since the copied file attribute is set to “read-only”, change it to the attribute which can be read or written. <Windows XP/2000> Select “Property”...
- Page 19 Click “OK”. The installation is completed above.
- Page 20 <Windows 98/ME> Select all files in the copied folder by a mouse. Select “File” and “Property”. Remove a check of “Read-only” and click “Apply”.
- Page 21 Click “Close”. Perform this setting to files in all folders of “3min_timer” and “ad_onkai”. The installation is completed above.
- Page 22 3) Connect a target board Use a user cable to the E8 emulator and connect a target board. Perform the below setting for the jumper setting of a target board. JP No. JP1 : “AN8” JP2 : “BZ” Connecting Status “AN8”...
- Page 23 The example of the musical scale program (ad_onkai.hws) is shown below. (1) Start High-performance Embedded Workshop Select “program” of start menu - “Renesas” - “High-performance Embedded Workshop” - “High-performance Embedded Workshop” and click. (2) Select “refer to another project work space” and click “OK”.
- Page 24 (4) Select “R5F21174” for Device and put a check into “Download emulator firmware” for Mode. Click “OK”. (5) When 5V power supply is performed from E8, put a check into “Power supply is carried out”. Select 5.0V and click “OK”. (6) Select location to download a firmware and click “OK”.
- Page 25 (3) Execute Click “Debug” - “Execute”. (4) If clicking “Debug” - “Stop a program”, a program will stop. When executing the program again, click “Debug” - “Execute”. <Musical Scale Program> When a program execution starts, LED1(red) lights up. When pressing SW4 on the target board, the buzzer starts sounding.
-
Page 26: Revision History
REVISION HISTORY Rev. Date Page 2004.08.18 0.10 1.00 2005.02.01 1.10 2005.03.01 First edition issued It changed from FDTlight to flash programmer (Flash Development Toolkit). The installation method changed, too. Add accessory softwares to install Description Summary... - Page 27 R8C/15, R8C/17 StarterKit Tutorial Publication Date Rev.1.10 Mar 01, 2005 Published by: Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan ©2005 Renesas Technology Corp. and Renesas Solutions Corp., All Rights Reserved. Printed in Japan.
- Page 28 R8C/15, R8C/17 StarterKit Tutorial Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan...