Table of Contents
Advertisement
Quick Links
To our customers,
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
Old Company Name in Catalogs and Other Documents
Renesas Electronics website:
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation
Advertisement
Table of Contents
Related Manuals for Renesas R8C/25
Summary of Contents for Renesas R8C/25
- Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
- Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
- Page 3 Renesas Starter Kit for R8C/25 User’s Manual RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / R8C/Tiny SERIES Rev.2.00 2007.10...
-
Page 4: Table Of Contents
Table of Contents Chapter 1. Preface ...1 Chapter 2. Purpose ...2 Chapter 3. Power Supply ...3 3.1. Requirements ...3 3.2. Power – Up Behaviour ...3 Chapter 4. Board Layout ...4 4.1. Component Layout ...4 4.2. Board Dimensions ...5 Chapter 5. Block Diagram ...6 Chapter 6. -
Page 5: Chapter 1. Preface
Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this document, either in whole or part is prohibited without the written permission of Renesas Solutions Corp. Trademarks All brand or product names used in this manual are trademarks or registered trademarks of their respective companies or organisations. -
Page 6: Chapter 2. Purpose
This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User Code Debugging. • User Circuitry such as Switches, LEDs and potentiometer(s). • User or Example Application. • Sample peripheral device initialisation code. The RSK board contains all the circuitry required for microcontroller operation. -
Page 7: Chapter 3. Power Supply
When the RSK is purchased the RSK board has the ‘Release’ or stand alone code from the example tutorial code pre-programmed into the Renesas microcontroller. On powering up the board the user LEDs will start to flash. After 200 flashes, or after pressing a switch the LEDs... -
Page 8: Chapter 4. Board Layout
4.1. Component Layout The following diagram shows the top layer component layout of the board. LCD Display Microcontroller Pin Headers (J1 to J4) Chapter 4. Board Layout Application Board Interface Application Board Interface Figure 4-1: Board Layout Reset Switch RS232 Serial Power Power LED E8 Header... -
Page 9: Board Dimensions
4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid for easy interfacing. 14.00mm 45.00mm 50.80mm 80.00mm 85.00mm Figure 4-2 : Board Dimensions 27.00mm... -
Page 10: Chapter 5. Block Diagram
Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. A pplic ation B oard Interface Mic roc ontroller P in Headers LIN Connector, P ower Connector for LIN S erial Connector Option Figure 5-2 is representative of the connections required to the RSK. Host PC P ower J ack Option B oot mode pins... -
Page 11: Chapter 6. User Circuitry
6.1. Switches There are four switches located on the RSK. The function of each switch and its connection are shown in Table 6-1. Switch When pressed, the RSK microcontroller is reset. SW1/BOOT* Connects to an IRQ input for user controls. The switch is also used in conjunction with the RES switch to place the device in BOOT mode when not using the E8a debugger. -
Page 12: Serial Port
6.4. Serial port The microcontroller programming serial port 1 is connected to the RS232 transceiver. This serial port can optionally be connected to the RS232 transceiver as well by fitting option resistors. The connections to be fitted are listed in the table 6-3. Description TxD1 RxD1... -
Page 13: Option Links
6.6.Option Links Table 6-5 below describes the function of the option links contained on this RSK board. Reference Function Reference Voltage Oscillator (Main clock) Oscillator (Main clock) Oscillator (Main clock) Oscillator (Main clock) Oscillator (Sub clock) Oscillator (Sub clock) Oscillator (Sub clock) Oscillator (Sub clock) - Page 14 Connects microcontroller pin 22 to LIN-NSLP Connects microcontroller pin 23 to LIN-RXD0 Connects microcontroller pin 23 to LIN-TXD0 Do not use CAN function, R8C/25 Microcontroller do not have CAN function Option Link Settings Fitted Alternative (Removed) External 3V3 disconnected from Board_VCC...
-
Page 15: Oscillator Sources
Function 6.7.Oscillator Sources A crystal oscillator is fitted on the RSK and used to supply the main and sub clock input to the Renesas microcontroller. Table 6-6: Oscillators / Resonators details the oscillators that are fitted and alternative footprints provided on this RSK:... -
Page 16: Chapter 7. Modes
The RSK supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the R8C/25 Group Hardware Manual. 7.1. Boot mode The boot mode settings for this RSK are shown in Table 7-1: Boot Mode pin settings below: MODE The software supplied with this RSK supports Boot mode using an E8a and HEW only. -
Page 17: Chapter 8. Programming Methods
Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E8a debugger. Refer to R8C/25 Group Hardware Manual for details of programming the microcontroller without using these tools. -
Page 18: Chapter 9. Headers
9.1. Microcontroller Headers Table 9-1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller connections. The header pins connect directly to the microcontroller pins. * Marked pins are subject to option links. Circuit Net Name No Connection TRISTn MODE_E8B RING_P4_4... - Page 19 Circuit Net Name IRQ0/TRIGa* IRQ2/IO_7* LCD_RS P3_1 IO_5 IO_3 No Connection Circuit Net Name No Connection P4_2/VREF IO_2 LCD_D7 LCD_D5 MO_UD Device Circuit Net Name IRQ1/IO_6* LCD_E AD_POT TMR1 IO_4 No Connection Table 9-3: J3 Device Circuit Net Name IO_0 IO_1 LCD_D6 LCD_D4...
-
Page 20: Application Headers
9.2. Application Headers Table 9-5 and Table 9-6 below show the standard application header connections. * Marked pins are subject to option links. Header Name RSK Signal Regulated Supply 1 CON_5V Regulated Supply 2 CON_3V3 Analogue Supply Analogue Reference CON_VREF ADC0 ADC2 DAC0... - Page 21 Function Power Supply (for LIN module) GROUND Function Power Supply (for LIN module) LIN Bus Line GROUND Table 9-7: LIN Headers Signal Name VBAT Signal Name VBAT...
-
Page 22: Chapter 10.Code Development
Chapter 10.Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the RSK board must be connected to a PC USB port via an E8a. An E8a is supplied with the RSK product. 10.2. Mode Support HEW connects to the Microcontroller and programs it via the E8a. Mode support is handled transparently to the user. -
Page 23: Memory Map
10.4. Memory Map 00000h 002FFh 00400h 00BFFh 02400h 02BFFh 08000h 0FFFFh Internal RAM User RAM Area Internal ROM Emulator Firmware (Data Area) Note: E8 Firmware area Emulator Firmware Internal ROM (Program Area) User ROM Area Fixed Vector Tables Figure 10-1: Memory Map Area selected via HEW Area... -
Page 24: Chapter 11. Component Placement
Chapter 11. Component Placement Figure 11-1: Component Placement... -
Page 25: Chapter 12. Additional Information
For information about the R8C/25 group microcontrollers refer to the R8C/25 Group Hardware Manual For information about the R8C/25 assembly language, refer to the R8C/Tiny Series Software Programming Manual. Online technical support and information is available at: Technical Contact Details America: techsupport.rta@renesas.com... - Page 26 Renesas Starter Kit for R8C/25 User's Manual Publication Date Rev.1.01 29.05.2006 Published by: Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan ©2006 Renesas Solutions Corp., Renesas Technology Europe Ltd. and Renesas Technology Corp., All Rights Reserved.
- Page 27 Renesas Starter Kit for R8C/25 User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10J1242-0200...