Ablerex GR1200 User Manual

This manual contains important safety instructions. Please follow all instructions during installation. Read this manual thoroughly before unpacking,
installing or operating.
Caution: Risk of Electric Shock
•
The UPS contains batteries. The output outlets may be electrically live even when the UPS is disconnected from the AC mains.
•
The UPS contains potentially hazardous voltages. Do not open the units as there are no user serviceable parts. All maintenance and
servicing should be performed by qualified service personnel.
•
Risk of electric shock, Battery Circuit is not isolated from AC input, hazardous voltage may exist between battery terminals and ground. Test
before servicing and use insulated tools.
NOTE: The UPS is designed to be for use with computer loads only.
Caution：Do not connect a laser printer to the UPS.
A laser printer draws significantly more power than other types of equipment and may overload the UPS.
Inspection
1
Inspect the UPS upon receipt.
Notify the carrier and dealer if there
is damage. The package is
recyclable; save it for reuse or
dispose of it properly.
Inspect accessories:
Power cable 1PCS
①
USER MANUAL 1PCS
Connect Modem/ Phone / Network for Surge Protection (Optional)
4
- For modem/phone line protection,
connect equipment to the RJ11
port using RJ11 cable.
- For surge protection, connect
equipment to the RJ45 port using
Ethernet/RJ45 cable.
Cold Start Function
7
When the UPS is OFF and no utility input
power is present, use the "Cold Start"
feature to apply power to the loads from
UPS's battery. Press the "ON/OFF" switch
until the UPS beeps.
GR600/GR800–LEDFRONT
PANEL(STANDARD)
GR1200/GR1800/GR2000 – LED
FRONT PANEL(STANDARD)
USER'S MANUAL
Choose an installation location
2
- Avoid locations that are excessively humid, near water,
near heat sources or in direct sunlight
- Allow 1inch (2.5cm) clearance on each side of the UPS
Software Download and Installation
8
Please follow steps below to download and install monitoring software:
1. Go to the website http://www.ablerex.com.sg/downloads.html
2. Depending on the computer OS, select Emily software (for Win 7&8 OS, select Emily2) and click download.
3. Follow the on-screen instructions to install the software.
4. When the computer restarts, the monitoring software automatically search and connects to the UPS.
FRONT PANEL EXPLANATIONS
LED
Symbol Description/function
Color
N/A Turn-on/Turn-off Switch
Lit: Line mode
Green Dim: Abnormal input
voltage and frequency
Lit: Battery mode
Yellow
Flashing: Battery Low
Lit: System malfunction
Red
or abnormal
Symbol LED Description/function
Color
N/A Turn-on/Turn-off Switch
Lit: Line mode
Green
Flashing: Battery mode
Lit: System malfunction or
Red
abnormal
N/A Load
N/A Battery
Load Percentage/
Green
Battery Capacity
GR1200
SETUP
Connecting Equipment and Power to the UPS
3
Step1: Connect the UPS to the
AC mains.
Step2: Connect the equipment
to the UPS output outlets.
Step3: Switch on the AC Mains,
follow by the UPS then the
equipment last.
*Plug the UPS into the AC
Mains to charge for 8 hours
before using the UPS.
Connect Interface Device
5
The UPS is equipped with
two interface ports: a USB
port (Standard) and a 9-pin
RS232 port (Optional)
allowing advanced
communication network
between the UPS and a
computer (network).
GR600/GR800/R1200/GR1800/GR2000
– LCD FRONT PANEL(OPTION)
REAR PANEL EXPLANATIONS
GR600/GR800 REAR PANEL
1. AC Input Outlet
2. Fuse
3. Output Connector:
4x Thailand Outlets
4. USB (Standard)
4
1
2
3
1
Turn ON/OFF the UPS
6
Turn on the UPS: Press the UPS
On/OFF Switchfor approx. 3
seconds, then the Buzzer sounds
twice, the UPS will start-up.
Turn off the UPS: Press the UPS
On/OFF Switch for approx. 3
seconds, then the Buzzer sounds
twice, the UPS will shutdown.
1.Line mode 4. Battery capacity
2.Battery mode 5. Load level
6.Measurement
3.AVR mode
Target & Value
GR1200/GR1800/GR2000 REAR PANEL
1. AC Input Outlet
2. Fuse
3. Output Connector:
6x Thailand Outlets
4. USB (Standard)
5. Fan
4
1
2
7.Fault
8.Tack switch for
Turn-on/Turn-off
5
3