Table of Contents
Advertisement
Quick Links
DisplayPort to CAT5e Daisy
Introduction
The DisplayPort to CAT5e Daisy Chain HD Extender Kit with
RS-232 & IR extends DisplayPort signal over one Cat5/6
cable up to 330ft and is cascade connection supported.
Features and Benefits
•
Extend DisplayPort signals up to 100m over Cat5e/
6 cabling
•
Cascade receivers up to 10 layers
•
Supports video high resolution Full HD 1080p, 1920
x 1080@60Hz
•
Supports local DisplayPort and audio output
•
Metal housing with mounting mechanism
Package Contents
CE-DP0511-S1
04-0955A
Chain HD Extender Kit
with RS-232 & IR
Installation Guide
1
Advertisement
Table of Contents
Related Manuals for SIIG CE-DP0511-S1
Summary of Contents for SIIG CE-DP0511-S1
-
Page 1: Installation Guide
Extend DisplayPort signals up to 100m over Cat5e/ 6 cabling • Cascade receivers up to 10 layers • Supports video high resolution Full HD 1080p, 1920 x 1080@60Hz • Supports local DisplayPort and audio output • Metal housing with mounting mechanism Package Contents CE-DP0511-S1 04-0955A... - Page 2 CE-DP0611-S1 Layout Transmitter Unit (Tx) Figure 1: Transmitter side panel • DC 5V: DC 5V power jack. Plug the included power adapter here • PWR: LED indicator for power status. On/Off when the Transmitter is powered on/off...
- Page 3 • LINK: LED indicator for link status. On when the connection of Transmitter and Receiver is established and detected • DP IN: DisplayPort signal input port. Connect this port to your DisplayPort source device by using a DisplayPort cable (not included) •...
- Page 4 • DC 5V: DC 5V power jack. Plug the included power adapter here • IR: Connect to the included IR receiver cable • RESET: Use the fine end of any object to press and hold the bottom to return to default settings •...
-
Page 5: Hardware Installation
IR Extension Cables To control the source device from Receiver's end: Plug the IR blaster cable to the Transmitter's IR connector, then plug the IR receiver cable to the Receiver's IR connector. Point your source device's remote control to the IR receiver's eye, the command will be sent to Transmitter end, and the connected source device will enforce the command accordingly. - Page 6 Connect remote DisplayPort display (such as a LCD TV) to the receiver's DP OUT connector. output display Figure 5 Connect the IR blaster cable and IR receiver cable to the Transmitter and Receiver's IR ports separately. Skip this step if not needed. Connect the two 3.5mm to RS-232 cables to the Transmitter and Receiver's RS-232 ports separately.
-
Page 7: Function Diagram
10. Plug the included power adapters into the DC 5V power jack of the Transmitter and Receiver separately. Power on the connected source device and display(s), the Extender kit is ready for use. Function Diagram Basic connection IR receiver remote DP cable display (optional) -
Page 8: Advanced Connections
Advanced Connections Daisy Chain Connection Display Display Display source CAT. X cable Display DisplayPort cable Figure 8 • The extension distance through CAT. X cable is up to 100 meters for one layer... - Page 9 Cascade Connection Display CAT. X cable DisplayPort cable Display Display source Display Figure 9 • Cascade receivers up to 10 layers; extension distance through CAT. X cable up to 100 meters for one layer...
- Page 10 Gigabit Ethernet Switch Connection CAT. X cable Display DisplayPort cable Gigabit switch Display Display source Display Figure 10: Used with Gigabit Ethernet switch • Connect with the Gigabit Ethernet switch especially when your Tx or Rx unit has only one signal input/ output port •...
-
Page 11: Technical Support And Warranty
(2) years from the date of purchase of the product. SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the product if defective in materials or workmanship. - Page 12 Fremont, CA 94538-3152, USA Phone: 510-657-8688 DisplayPort to CAT5e Daisy Chain HD Extender Kit with RS-232 & IR is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation.
Need help?
Do you have a question about the CE-DP0511-S1 and is the answer not in the manual?
Questions and answers