Advertisement
Quick Links
XMP100
Digital Stereo Power Amplifier
FEATURES:
• Class D Amplification (89% Efficient)
• MAIN / INTERRUPT priority input switching
• MAIN auxiliary output
• Speaker A/B switching
• Front panel Balance and Volume controls
• Signal sensing "Power On" and Trigger mode
• Rear mounted treble and bass controls
SPECIFICATIONS
Stereo (8 ohm):
50W per channel, <1% THD+N
Stereo (4 ohm):
75W per channel, <1% THD+N
Bridged Mono (8 ohm):
160W, 1kHz, <1% THD+N
Frequency Response:
10Hz ~ 30kHz, -2dB/ +1dB
Signal to Noise Ratio:
100dB below 50W output into 8 ohms
w/20kHz Lowpass filter
Channel Separation:
65dB @ 1kHz, referred to 50W output
into 8 ohms
Input Sensitivity:
700mV input for rated 50W output
into 8 ohms
Bass/Treble Control:
+/- 12dB @ 100Hz and 10kHz
AC Power Consumption:
200W maximum
Net Weight:
4.7lbs / 2.2kgs
Gross Weight:
6.8lbs / 3kgs
OsdAudio ®
775 Columbia St.,
Brea. CA92821
www.osdaudio.com
Congratulations on your purchase of the OsdAudio ® XMP100.
Please take a few moments to read this entire manual, and be sure to
retain this document for future reference. Please read and observe all
safety instructions detailed on page 2.
NOTE: If any part of this product is damaged or missing, please call your
dealer or OsdAudio ® directly at 888 779 4968.
Please read your warranty and retain your receipt and original carton
for possible future use.
For more information about OsdAudio ® electronics, speakers and
accessories please visit www.osdaudio.com
2.15"
(55mm)
7.65"
(194mm)
XMP100
OWNER'S MANUAL
XMP100
D I G I TA L P O W E R
A M P L I F I E R
16.9" (430mm)
XMP100 Owner's Manual 51115
XMP100
D I G I TA L P O W E R
A M P L I F I E R
Advertisement
Related Manuals for OSD Audio XMP100
Summary of Contents for OSD Audio XMP100
-
Page 1: Specifications
D I G I TA L P O W E R A M P L I F I E R XMP100 Congratulations on your purchase of the OsdAudio ® XMP100. Digital Stereo Power Amplifier Please take a few moments to read this entire manual, and be sure to FEATURES: retain this document for future reference. - Page 2 For a period of two years f r om from a stereo pre-amplifier or source to the MAIN input jacks of your XMP100. date of original pu r chase, we will r epair or r eplace the p r oduct, at our option, Next connect your speakers to the terminals marked “Speaker A”...
-
Page 3: Rear Panel Controls
NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both Allows the XMP100 to be powered on by other electronics or to power A and B speaker terminals! This may result in a lower impedance than the on other electronics via a 3.5mm mini phone plug cable. - Page 4 XMP100 OWNER’S MANUAL CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SE R VICABLE P A R TS INSIDE. REFER SE R VICING TO QUALIFIED PERSONNEL! The exclamation point within an equ i lateral triangle is intended to alert the user of the p r esence of important operating and maintenance (servicing) instructions in the literatur e accompanying the appliance.