Related Manuals for OSD Audio NERO XA5180
Summary of Contents for OSD Audio NERO XA5180
- Page 1 NERO H O M E T H E A T E R NERO XA5180 OWNER’S MANUAL (This manual applies to all XA amps, the diagrams show the XA5180, however the connections etc., are the same for all XA amps)
- Page 2 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ FIRST General Note on the Declaration of Conformity: We hereby declare that this device is in accordance with the essential requirements of the European Directive 2014/35/EU or 2001/95/EC (if applicable). The full EU declaration of conformity can be requested at the following address: InMusic GmbH Harkortstr.
-
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Protective earthing terminal(For class I apparatus with earthing). The apparatus should be connected to a mains socket outlet with a protective earthing connection. (For class II apparatus only)This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. - Page 4 AMP5 AMP4 AMP3 AMP2 AMP1 Audio Inputs Speaker Outputs (see page 4) (see page 4) Inputs for connecting the XA Amplifier to the outputs of a Use these 5-way binding posts to connect the XA Amp to surround processor, preamplifier AV receiver with pre-out your speakers.
-
Page 5: Connecting Your Speakers
SPEAKER & INPUT CONNECTION INPUTS: Non Balanced RCA NERO XA5180 MODEL: Balanced XLR ATTENTION OUTPUTS: Connect to Speakers Connecting your speakers: Use Class 2 wiring for speaker connections. Wiring the speaker connector with bare wire: 1. Strip the insulation off each speaker wire to expose 3/8" (10 mm) of bare conductor. -
Page 6: Auto Power On
AUTO POWER ON NERO XA5180 MODEL: Remote Trigger ATTENTION Auto Power ON To use another device with a 12 volt trigger output jack to automatically power on the XA: 1. Select Trigger position. 2. Connect a 3.5mm mono jack from the trigger-output jack of the source device to the REMOTE TRIGGER jack on the When the switch is set to TRIGGER, the goes into standby mode and the front panel LED’s glow yellow. -
Page 7: Amplifier Operation And Maintenance
AMPLIFIER OPERATION AND MAINTENANCE Before you begin: Ensure that the amp is plugged into a 15 Amp power socket. At full power the amp will require in excess of 10 Amps. Ensure the amp has air clearance with nothing covering the ventilation slots. 6 inches of clearance is recommended, or, if rack mounted, please use a cooling fan. -
Page 8: Power-On - Trigger
AMPLIFIER OPERATION AND MAINTENANCE Power-on – Trigger Press the front panel power button. After a short pause the front panel LED indicators will light-up. When the rear panel switch is set to TRIGGER the front panel indicator lights will be Yellow/Orange and the amp will be in Standby mode. When a TRIGGER signal is present the amp will turn on and the indicator lights will be Blue. -
Page 9: Performance Specs
PERFORMANCE SPECS XA7180 AMP 1 AMP 2 AMP 3 AMP 4 AMP 5 AMP 6 AMP 7 OUTPUT POWER (RMS) (UNIT:W) @1% THD (SINGLE CHANNEL) 4 Ohms OUTPUT POWER (RMS) (UNIT:W),@5% THD (SINGLE CHANNEL) 4 Ohms OUTPUT POWER (RMS) (UNIT:W) @1% THD (SINGLE CHANNEL) 8 Ohms ALL CHANNEL OUTPUT POWER (RMS) (UNIT:W) @0.1% THD 8 Ohms... -
Page 10: Specifications
RMA@audiogeargroup.com for a Returned Merchandise Authorization (RMA) number then the unit must be shipped to OSD AUDIO at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the product(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.