Advertisement

Quick Links

C
ONDENSED
References
refer to a specific chapter of the
User's Manual.
For further information, please refer to the User's Manual
supplied with your unit.

DETECTOR CONNECTIONS

-2
10
10
-3
10
-4
COR
ZERO
-5
10
-6
10
INLET
-7
3
TEST
10
10
Remote control
10
2
-8
10
HIGH
1
10
-9
10
1
-10
10
10
-1
SNIF
(accessory not
-2
10
-11
10
VENT
10
-3
-12
10
mbar
mbar.l/s
delivery)
CYCLE
AUTO CAL
ZERO
A 400
SD card
Printer
(not delivered, payable
by the customer)
or
External control
system
(I/O interface)
SubD 15 pins
Controlling the detector
with a PC through
the RS 232 interface
(PC not included, payable
Main power switch
by the customer)
Power fuse + exchange fuse

OPERATOR INTERFACE

Application window
(touch-sensitive screen)
M
ANUAL
ASM 310
2
1
Change the application
window (come back to
home).
Change the level.
Start the function
allocated.
APPLICATION WINDOWS
SD card
Allows the operator to set/
Setting
confi gure the detector
Sniffer probe
according ti its needs
(accessory
not delivery)
Inlet DN 25
A 400
Inlet vent
and neutral
gas purge
CAUTION
Do not seal
Exhaust connector
(with silencer)
CAUTION
Do not seal
Main power cable
Function keys allowing the
1
activation of the associated
functions.
6
Functions allocated to the function
2
keys.
3
Start/Stop of a test.
5
4
Level change.
Application window change,
4
5
come back to home (standard
display).
START
Remote control connection
STAND-BY
6
3
(accessory).
Start/Stop the test
Place the blank-off fl ange on the detector
inlet (detector state on delivery).
Start the test.
START
STAND-BY
The helium signal displays the
measured value : it corresponds in our
case to the detector background.
Stop the test.
START
STAND-BY
To remove the blank-off flange, do an
air inlet.
Inform the operator
Standard
of the test
display
Allows the operator to follow
Graphic
and to record the He signals
and the pressure according
display
to time
Indicate to the operator the leak
Vacuum
detector vaccum circuit as well
circuit
as the valves state
The operator can mask, add,
switch some windows
in the loop
C 403.
The operator can have only
a single application window
displayed.

ASSISTANCE TO THE TEST

Hard vacuum test mode

Select the hard vacuum
test mode (
C 402)
While the leak detector is in stand-by,
Connect the part to be tested to the leak
connect the sniffer probe (accessory to be
detector inlet port or put the part in the test
purchased separately) to the sniffer port of
chamber connected to the leak detector.
the leak detector.
Select the reject point (
START
Start the test
STAND-BY
The leak value measured displays.
START
STAND-BY
Stop the test
The detector returns automatically to stand-by mode.
If Memo function is activated and a printer is connected to the detector,
a test ticket will be printed automatically after the test (
MAIN FONCTIONS

Set Points

C 401
2 adjustable set points:
reject set point in hard vacuum,
reject set point in sniffing.
Define the acceptance threshold of the good/bad parts:
leak value measured ≤ reject set point => part accepted.
leak value measured > reject set point => part rejected.

Audio alarm set points

C 401
Digital voice informs the operator about the detector state or the actions to do.
The audio alarm informs the operator that the reject set point was crossed. The level
varies from 0 to 8 (0 to 90 dB).
or
Stop simultaneously the audio alarm and the digital voice with the key

Autocalibration

C 406
It allows to check that the detector is adjusted to detect the selected tracer gas and dis-
play a correct leak value.
By default, autocalibration is set ON and the internal calibrated leak is selected to allow
a quick leak detector autocalibration.
Autocal = ON : the detector will be automatically calibrated at each switching on.
At any time, the operator can start an autocalibration (
Sniffi ng test mode
Select the sniffing test
mode (
C 402)
C 401)
C 406)
.
).

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ASM 310 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pfeiffer Vacuum ASM 310

  • Page 1 (accessory to be Level change. detector inlet port or put the part in the test purchased separately) to the sniffer port of chamber connected to the leak detector. ASM 310 Application window change, the leak detector. come back to home (standard display).
  • Page 2 2 years CS : Please contact Customer Service (1) running time (2) running time or storage (3) storage Pfeiffer Vacuum GmbH Pfeiffer Vacuum GmbH Headquarters Headquarters * Service intervals: The service intervals given are for applications and work rates which conform...

Table of Contents