Daikin ERLQ004CA Installer's Reference Manual page 99

6/9
Field settings table
Breadcrumb Field code Setting name
A.8 [2-02] When should the disinfection function start?
A.8 [2-03] What is the disinfection target temperature?
A.8 [2-04] How long must the tank temperature be maintained?
A.8 [2-05] Room antifrost temperature
A.8 [2-06] Room frost protection
A.8 [2-09] Adjust the offset on the measured room temperature
A.8 [2-0A] Adjust the offset on the measured room temperature
A.8 [2-0B] What is the required offset on the measured outdoor temp.?
A.8 [3-00] Is auto restart of the unit allowed?
A.8 [3-01] --
A.8 [3-02] --
A.8 [3-03] --
A.8 [3-04] --
A.8 [3-05] --
A.8 [3-06] What is the maximum desired room temperature in heating?
A.8 [3-07] What is the mimimum desired room temperature in heating?
A.8 [3-08] What is the maximum desired room temperature in cooling?
A.8 [3-09] What is the minimum desired room temperature in cooling?
A.8 [4-00] What is the BUH operation mode?
A.8 [4-01] Which electric heater has priority?
A.8 [4-02] Below which outdoor temperature is heating allowed?
A.8 [4-03] Operation permission of the booster heater.
A.8 [4-04] --
A.8 [4-05] --
A.8 [4-06] -- (Do not change this value)
A.8 [4-07] Enable the second step of the backup heater?
A.8 [4-08] Which power limitation mode is required on the system?
A.8 [4-09] Which power limitation type is required?
A.8 [4-0A] --
A.8 [4-0B] Automatic cooling/heating changeover hysteresis.
A.8 [4-0D] Automatic cooling/heating changeover offset.
A.8 [5-00] Is backup heater operation allowed above equilibrium temperature during space
heating operation?
A.8 [5-01] What is the equilibrium temperature for the building?
A.8 [5-02] Space heating priority.
A.8 [5-03] Space heating priority temperature.
A.8 [5-04] Set point correction for domestic hot water temperature.
A.8 [5-05] What is the requested limit for DI1?
A.8 [5-06] What is the requested limit for DI2?
A.8 [5-07] What is the requested limit for DI3?
A.8 [5-08] What is the requested limit for DI4?
A.8 [5-09] What is the requested limit for DI1?
A.8 [5-0A] What is the requested limit for DI2?
A.8 [5-0B] What is the requested limit for DI3?
A.8 [5-0C] What is the requested limit for DI4?
A.8 [5-0D] What type of backup heater installation is used?
A.8 [5-0E] --
A.8 [6-00] The temperature difference determining the heat pump ON temperature.
A.8 [6-01] The temperature difference determining the heat pump OFF temperature.
4P383508-1B - 2017.04
Range, step
Default value
R/W 0~23 hour, step: 1 hour
23
R/W [E-07]≠ 55~80°C, step: 5°C
1 :
70°C
[E-07]=1 : 60°C
60°C
R/W [E-07]≠1: 5~60 min, step: 5 min
10 min
[E-07]=1: 40~60 min, step: 5 min
40 min
R/W 4~16°C, step: 1°C
12°C
R/W 0: Disabled
1: Enabled
R/W -5~5°C, step: 0,5°C
0°C
R/W -5~5°C, step: 0,5°C
0°C
R/W -5~5°C, step: 0,5°C
0°C
R/W 0: No
1: Yes
0
1
4
2
1
R/W 18~30°C, step: A.3.2.4
30°C
R/W 12~18°C, step: A.3.2.4
12°C
R/W 25~35°C, step: A.3.2.4
35°C
R/W 15~25°C, step: A.3.2.4
15°C
R/W 0: Disabled
1: Enabled
2: Only DHW
R/W 0: None
1: BSH
2: BUH
R/W 14~35°C, step: 1°C
25°C (*5)
14~35°C, step: 1°C
35°C (*6)
R/W 0: Limited
1: No limit
2: Most optimum
3: Optimum
4: Only legionella
2
0
0/1
R/W 0: No
1: Yes
R/W
0: No limitation
1: Continuous
2: Digital inputs
R/W 0: Current
1: Power
0
R/W 1~10°C, step: 0,5°C
1°C
R/W 1~10°C, step: 0,5°C
3°C
R/W 0: Allowed
1: Not allowed
R/W -15~35°C, step: 1°C
0°C
R/W 0: Disabled [E-07]≠
1
1: Enabled [E-07]=1
R/W -15~35°C, step: 1°C
0°C
R/W 0~20°C, step: 1°C
10°C
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0: 1P,(1/2)
1: 1P,(1/1+2) (*3)
2: 3P,(1/2)
3: 3P,(1/1+2)
4: 3PN,(1/2)
5: 3PN,(1/1+2) (*4)
1
R/W 2~20°C, step: 1°C
2°C
R/W 0~10°C, step: 1°C
2°C
Installer setting at variance with
default value
Date Value
(*1) *HB*_(*2) *HV*_
(*3) *3V_(*4) *9W_
(*5) *04/08*_
(*6) *11/16*