Table of Contents
Advertisement
CYCLE DEFAULTS TABLE continued
PRF40K Recharge Cycles:
Length of Cycle
Cycle
Cycle
HE
Description
Setting
1
Backwash 1
10 min
2
Brine Draw
51 min
Slow Rinse
3
Re-
3 min
Pressurize
4
Fast Rinse 1
4 min
5
Backwash 2
1 min
6
Fast Rinse 2
1 min
7
Refill
4 .1min
*The camshaft does not move between Brine Draw and Slow Rinse .
Slow Rinse begins when the brine in the salt tank runs out and the
check valve closes .
PRF26K Recharge Cycle Requirements:
Minimum Salt/
Salt/Recharge (lbs)
Regeneration Time
(min)
Water to Drain (gal)
Max . Flow to Drain
(gpm)
PRF34K Recharge Cycle Requirements:
Minimum Salt/
Salt/Recharge (lbs)
Regeneration Time
(min)
Water to Drain (gal)
Max . Flow to Drain
(gpm)
PRF40K Recharge Cycle Requirements:
Minimum Salt/
Salt/Recharge (lbs)
Regeneration Time
(min)
Water to Drain (gal)
Max . Flow to Drain
(gpm)
START-UP
The conditioner will now need to be placed into operation .
Please review Quick Cycling the Control procedure before
attempting start-up .
DO NOT put regenerant material into the brine tank .
1 . With the supply water for the system still turned off, position
the bypass valve to the "not in bypass" (normal operation)
position .
12 • PRF26K, PRF34K, and PRF40K
Time remaining to
end of cycle
HC
HE
Setting
Setting
Setting
10 min
74 .1 min
118 .1 min
79 min
64 .1 min
108 .1 min
3 min
13 .1 min
29 .1 min
4 min
10 .1 min
26 .1 min
1 min
6 .1 min
22 .1 min
1 min
5 .1 min
21 .1 min
20 .1 min
4 .1 min
20 .1 min
Maximum Salt/
Capacity
Capacity
2 .6
12 .8
75
109
37
44
1 .7
1 .7
Maximum Salt/
Capacity
Capacity
3 .4
16 .7
76 .5
117 .5
46 .3
56 .9
2 .1
2 .1
Maximum Salt/
Capacity
Capacity
4 .1
20
74 .1
118 .1
58 .7
72 .1
2 .7
2 .7
HC
Both valve
handles pointing
in direction of
water flow
2 . Press and hold the
seconds . This will initiate a manual regeneration, and cycle
to the backwash position .
3 . Filling the media tank with water .
A . With the conditioner in backwash, open the water
supply valve very slowly to approximately the 1/4 open
position . Water will begin to enter the media tank . Air
will begin to be purged to drain as the media tank fills
with water .
WARNING:
If opened too rapidly or too far, media may
be lost out of the tank into the valve or the
plumbing. In the 1/4 open position, you
should hear air slowly escaping from the
valve drain line.
B . When all of the air has been purged from the media
tank (water begins to flow steadily from the drain line),
open the main supply valve all of the way . This will
purge the final air from the tank.
C . Allow water to run to drain until the water runs clear
from the drain line . This purges any debris from the
media bed .
D . Pour about 3 gallons of water into the brine tank .
Advance to cycle 2 (Brine Draw) by pressing the
and
buttons at the same time . The water in the brine
tank should be drawn into the valve . If the water is not
receding from the tank, refer to Troubleshooting .
E . Quickly cycle the control to the refill cycle (C7). Place
salt in brine tank. Allow this cycle to finish and the
control to move to service . The brine tank will have the
correct amount of water .
WARNING:
Ensure that the system has been properly
disinfected per the water conditioning
system manufacturer's recommendations.
The water conditioning system is now fully operational.
The display will show the hour of the day . The decimal point at
bottom center of the display will blink when water is flowing.
INSTALLATION CHECKLIST
___ Read the owner's/installation manual?
___ Follow all safety guidelines in the manual?
___ If metal pipe was used, did you restore the electrical ground?
___ Securely install both drain hoses to an approved drain?
___ Perform a leak test?
___ Move the bypass valve to service?
___ Sanitize the softener?
___ Add salt pellets to the salt storage tank?
___ Program the control correctly to meet your needs?
___ Start a recharge?
button on the controller for 3
Advertisement
Table of Contents
