Group:protection Function Parameters - Toshiba Tosvert-130 Installation Manual

8.3.7 GROUP:PROTECTION FUNCTION PARAMETERS

Reg. Function / Title
11F DYNAMIC BRAKING SELECTION
120 2 BRAKING RESISTOR VALUE
121 BRAKING RESISTOR POWER RATING
122 OVERVOLTAGE STALL PROTECTION
123 DC INJECTION START FREQUENCY
124 Other DC INJECTION CURRENT MAGNITUDE
125 than 0 DC INJECTION TIME
126 FWD/REV DC INJECTION PRIORITY CTRL
127 MOTOR SHAFT STATIONARY CTRL
128 EMERGENCY OFF MODE SELECTION
129 2 EMERGENCY OFF DC INJECTION TIME
12A NUMBER OF RETRY ATTEMPTS
12B Other TIME BETWEEN RETRY ATTEMPTS
than 0
12C REGENERATION POWER RIDE-THROUGH
12D 1 REGENERATION RIDE-THROUGH TIME
12E AUTO-RESTART (MOTOR SPEED SEARCH)
12F ELECTRONIC THERMAL PROTECT LVL #1
130 OVERLOAD REDUCTION START FREQ
131 MOTOR 150% OVERLOAD TIME LIMIT
132 OVERLOAD SELECTION
133 STALL PROTECTION ENABLE
134 0 STALL PROTECTION CURRENT LEVEL
135 UNDERVOLTAGE TRIP SELECTION
136 UNDERVOLTAGE DETECT TIME
137 LOW CURRENT DETECT SELECTION
138 LOW CURRENT DETECT LEVEL
139 LOW CURRENT DETECTION TIME
140 OUTPUT SHORT-CIRCUIT DETECTION SELECT
141 OVERTORQUE TRIP SELECTION
142 OVERTORQUE TRIP LEVEL
Bank Address
(Note) 0 / 1 04BD
0 / 1 0416
0 / 1 0418
0 / 1 04BD
0 / 1 03FC
0 / 1 043A
0 / 1 043B
0 / 1 04BC
0 / 1 04BC
0 / 1 04BC
0 / 1 043D
0 / 1 043F
0 / 1 0440
0 / 1 04BD
0 / 1 0446
0 / 1 04B6
0 / 1 042A
0 / 1 0410
0 / 1 0444
0 / 1 04BD
0 / 1 042D
0 / 1 042B
0 / 1 04BD
0 / 1 0414
0 / 1 04BC
0 / 1 0441
0 / 1 0442
0 / 1 04BE
0 / 1 04BE
0 / 1 0443
22
Mask Adjustment Range
0003 0000: no dynam. Braking
0001: with dynamic braking,
no DBR OL trip
0002: with dynamic braking
and DBR OL trip
FFFF 000A ∼ 2710 (1.0 ∼ 1000)
FFFF
0001 ∼ EA60 (0.01 ∼ 600.00)
0004 0000: ON
0001: OFF
FFFF
0000 ∼ 2EE0 (0.00 ∼ 120.00)
00FF 0000 ∼ 0064 (0 ∼ 100)
00FF 0000 ∼ 0064 (0.0 ∼ 10.0)
0040 0000: OFF
0001: ON
0080 0000: OFF
0001: ON
0030 0000: Coast stop
0001: Decelerated stop
0002: DC injection stop
00FF 0000 ∼ 0064 (0.0 ∼ 10.0)
00FF
0000 ∼ 000A (0 ∼ 10)
00FF 0000 ∼ 0064 (0.0 ∼ 10.0)
0008 0000: OFF
0001: ON
00FF 0000 ∼ 00FA (0.0 ∼ 25.0)
0018 0000: OFF
0001: On power failure
0002: On ST make/break
0003: Both (1) and (2)
00FF 000A ∼ 0064 (10 ∼ 100)
FFFF
0000 ∼ 0BB8 (0.00 ∼ 30.00)
00FF 0001 ∼ 00F0 (10 ∼ 2400)
0030 0000: with motor overload trip,
w/o soft-stall
0001: with motor overload trip
and soft-stall
0002: w/o soft-stall or motor
overload trip
0003: with soft-stall, w/o motor
overload trip
0040 0000: ON
0001: OFF
00FF
000A ∼ 00D7 (10 ∼ 215)
0080 0000: Trip disabled
0001: Trip (during run)
FFFF
0000 ∼ 03E8 (0.00 ∼ 10.00)
0008 0000: Trip disabled
0001: Trip on detection
00FF 0000 ∼ 0064 (0 ∼ 100)
00FF 0000 ∼ 00FF (0 ∼ 255)
0003 0000: Standard motor
0001: High-speed motor
0002: Positioning use
(standard motor)
0003: Positioning use (high-
speed motor)
0040 0000: Trip disabled (0)
0001: Trip enabled (1)
00FF 0000 ∼ 00C8 (0 ∼ 200)
Multiplier

0.1
0.01

0.01
1
0.1



0.1
1
0.1

0.1

1
0.01
10


1

0.01

1
1


1