Group:fundamental Parameters #2; Group:panel Control Parameters; Group:terminal Selection Parameters - Toshiba Tosvert-130 Installation Manual

GROUP:FUNDAMENTAL PARAMETERS #1 (Cont.)
Register Function / Title
31 ACC/DEC PATTERN #1 SELECTION
32 ACCEL/DECEL PATTERN ADJUST LOW
33 ACCEL/DECEL PATTERN ADJUST HIGH

8.3.2 GROUP:FUNDAMENTAL PARAMETERS #2

Reg. Function / Title
34 BASE FREQUENCY #2
35 MAXIMUM OUTPUT VOLTAGE #2
36 VOLTAGE BOOST #2
37 ELECTRONIC THERMAL PROTECT LVL #2
38 STALL PROTECTION SELECTION #2
39 0 STALL PROTECTION LEVEL #2
3A ACCELERATION TIME #2
3B DECELERATION TIME #2
3C ACC/DEC PATTERN #2 SELECTION
3D ACC/DEC #1/#2 SWITCH FREQUENCY

8.3.3 GROUP:PANEL CONTROL PARAMETERS

Reg. Function / Title
3E DIRECTION SELECTION (FORWARD/REV)
3F STOP PATTERN SELECTION
40 FUNDAMENTAL PARAM SWITCHING
41 ACCEL/DECEL #1/#2 SELECTION
42 PANEL RESET SELECTION
43 PANEL FEEDBACK CONTROL

8.3.4 GROUP:TERMINAL SELECTION PARAMETERS

Reg. Function / Title
44 INPUT TERMINAL SELECTION
45 1 "R" INPUT TERMINAL FUNCTION
46 "S1" INPUT TERMINAL FUNCTION
47 "S2" INPUT TERMINAL FUNCTION
48 "S3" INPUT TERMINAL FUNCTION
49 "S4" INPUT TERMINAL FUNCTION
4A "F" INPUT TERMINAL FUNCTION
4B "RES" INPUT TERMINAL FUNCTION
4C "ST" INPUT TERMINAL FUNCTION
4D "S5" INPUT TERMINAL FUNCTION
4E "S6" INPUT TERMINAL FUNCTION
4F "S7" INPUT TERMINAL FUNCTION
50 POTENTIAL TERMINAL FUNCTION
51 R,S1-S7 TERMINAL RESPONSE TIME
52 F INPUT TERMINAL RESPONSE TIME
53 RES INPUT TERMINAL RESPONSE TIME
54 ST INPUT TERMINAL RESPONSE TIME
Bank
0 / 1
0 / 1
0 / 1
Bank
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
(Ref. 1) 0 / 1
0 / 1
0 / 1
0 / 1
Bank
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
(Note 1) 0 / 1
Bank
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
0 / 1
Address Mask Adjustment Range
042D 0030 0000: Linear
0001: Self-adjusting
0002: S-Pattern #1
0003: S-Pattern #2
04C4 00FF 0000~00032 (0 ∼ 50)
04C5 00FF 0000~00032 (0 ∼ 50)
Address Mask Adjustment Range
0432 FFFF 09C4 ∼ 9C40 (25.00 ∼ 400.00)
0430 FFFF
0000 ∼ 0258 (0 ∼ 600)
042E FFFF 0000 ∼ 012C (0.0 ∼ 30.0)
0434 00FF
000A ∼ 0064 (10 ∼ 100)
0437 0040 0000: ON (0)
0001: OFF (1)
0435 00FF
000A ∼ 00D7 (10 ∼ 215)
03CA FFFF
0001 ∼ EA60 (0.01~ 6000)
0001 ∼ EA60 (0.01~ 600)
03CC FFFF 0001 ∼ EA60 (0.01~ 6000)
0001 ∼ EA60 (0.01~ 600)
0437 0030 0000: Linear
0001: Self-adjusting (1)
0002: S-Pattern #1 (2)
0003: S-Pattern #2 (3)
0406 FFFF 0000 ∼ Fmax
Address Mask Adjustment Range
04FA 0004 0000: Reverse
0001: Forward
045C 0040 0000: Decelerated stop (0)
0001: Coast stop
04FB 0004 0000: V/F #1
0001: V/F #2
04FA 0008 0000: Acc / dec #1 (1)
0001: Acc / dec #2 (2)
045C 0030 0000: All possible
0001: overload only (1)
0002: overload, overcurrent
only (2)
04FB 0001 0000: Feedback valid (0)
0001: Feedback invalid (1)
Address Mask Adjustment Range
04BB 0001 0000: Standard functions (0)
0001: Individual selection (1)
046C FFFF
0000 ∼ FFFF (0 ∼ 54)
046E FFFF Refer to Table 6
0470 FFFF in RS-485 manual
0472 FFFF
0474 FFFF
0476 FFFF
0478 FFFF
047A FFFF
047C FFFF
047E FFFF
0480 FFFF
0482 FFFF
0462 00FF 0001 ∼ 0064 (1 ∼ 100)
0463 00FF
0001 ∼ 0064 (1 ∼ 100)
0464 00FF 0001 ∼ 0064 (1 ∼ 100)
0465 00FF
0001 ∼ 0064 (1 ∼ 100)
18
Multiplier

Multiplier
0.01
1
0.1
1

1
0.1
0.01
0.1
0.01
(0) 
0.01
Multiplier
(0) 
(1)

(1)
(1) 
(2)

(0)


Multiplier


1
1
1
1