Related Manuals for OLIMEX OLIMEXINO-328
Summary of Contents for OLIMEX OLIMEXINO-328
- Page 1 OLIMEXINO-328 an Arduino-like development board USER’S MANUAL Document revision E, August 2017 Designed by OLIMEX Ltd, 2011 All boards produced by Olimex LTD are ROHS compliant...
-
Page 2: Disclaimer
This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product. -
Page 3: Table Of Contents
1.2 Improvements over the original Arduino design ..............5 1.3 Target market and purpose of the board ................7 1.4 Document organization ......................7 CHAPTER 2 – SETTING UP THE OLIMEXINO-328 ........... 8 2. Introduction to the chapter ....................... 8 2.1 Electrostatic warning ....................... 8 2.2 Requirements ........................... - Page 4 OLIMEX© 2017 OLIMEXINO-328 user's manual 6. Introduction to the chapter ..................... 18 6.1 Eagle schematics ........................18 6.2 Physical dimensions ....................... 20 CHAPTER 7 – REVISION HISTORY AND SUPPORT ........21 7. Introduction to the chapter ..................... 21 7.1 Document revision ......................... 21 7.2 Board revision ........................
-
Page 5: Chapter 1 - Overview
Thank you for choosing the OLIMEXINO-328 board from Olimex! This document provides a user’s guide for the Olimex Arudino-like OLIMEXINO-328. As an overview, this chapter gives the introduction to Arduino, the scope of this document and lists the features of the board. The document’s organization is then detailed. - Page 6 OLIMEX© 2017 OLIMEXINO-328 user's manual to use virtually any power supply adapter on the market, including applications with the standard 24VDC industrial power supply. 3. We carefully selected all components to work reliably over the industrial temperature range -25+85C so the board can be used in industrial applications (the original design was suitable for the commercial 0-70C operating temperature).
-
Page 7: Target Market And Purpose Of The Board
Revision B and revision C boards and resources were used while writing this document. It is possible that all revisions used to create the document are outdated so it is recommended to download the latest sources from the web-page of OLIMEXINO-328 at the official www.olimex.com web-site. -
Page 8: Chapter 2 - Setting Up The Olimexino-328
General practice for working with static sensitive devices should be applied when working with this board. 2.2 Requirements In order to set up the OLIMEXINO-328 optimally, you might need to update your set of hardware and/or software tools. The major needed components are listed below. Hardware tools:... -
Page 9: Connecting To Arduino Ide
The first time you connect the board you would be asked for drivers. You can find the drivers needed for OLIMEXINO-328 in the install folders of the Arduino IDE (usually in folder “drivers”). After the drivers are successfully installed you should run the Arduino IDE. -
Page 10: Chapter 3 - Olimexino-328 Board Description
3. Introduction to the chapter Here you get acquainted with the main parts of the board. Note the names used on the board differ from the names used to describe them. For the actual names, please, check the OLIMEXINO-328 itself. -
Page 11: Layout (Bottom View)
OLIMEX© 2017 OLIMEXINO-328 user's manual 3.2 Layout (bottom view) Page 11 of 24... -
Page 12: Chapter 4 - Control Circuity
The board can operate at either 3.3V or 5V, selected via a switch. When operating at 5V ensure that the boards connected to OLIMEXINO-328 can also operate at 5V. If you are not sure, set the switch to 3.3V operation. -
Page 13: Chapter 5 - Interfaces And Hardware
5.2 PWR_J connector The power jack used is the typical one used by Olimex in most of our products – the DC barrel jack has 2.0mm inner pin and 6.3mm hole. More information about the exact component might be found here: https://www.olimex.com/wiki/PWRJACK. -
Page 14: Arduino Shield Platform
These four connectors are usually used when you want to mount extension shield on the OLIMEXINO-328. The shield connector layout follows the original Arduino layout and spacing BUT we have also provided set of metalized holes that improve the layout by keeping 0.1'' step between connectors. -
Page 15: Con4 - Digital
D11(MOSI) D12(MISO) D13(SCK/LED1) AREF 5.4 LIPO_BAT connector The LIPO_BAT connector comes handy when you want to use the OLIMEXINO-328 as a stand- alone device. Pin # Signal name VBAT Olimex LTD has a number of batteries with the proper connector. They might be found here: https://www.olimex.com/Products/Power/... -
Page 16: Jumper Description
OLIMEX© 2017 OLIMEXINO-328 user's manual connector or jumper wires to be able to connect your AVR programmer tool. Please make sure you are not trying to use TPI or PDI interface with the ICSP pads. If your programmer has only 10 pin ICSP cable you would need to use jumper wires or adapter to be able to connect to the 6 pin interface. -
Page 17: Leds And Buttons
(UART, SPI, I2C). Most Olimex-manufactured UEXT modules work at 3.3V – they would get damaged if the jumper is set to 5V. When using Olimex MOD- board on this UEXT ensure the jumper is set to 3.3V, else you might damage the module. -
Page 18: Chapter 6 - Schematics
OLIMEX© 2017 OLIMEXINO-328 user's manual CHAPTER 6 – SCHEMATICS 6. Introduction to the chapter In this chapter is located information about the schematics describing logically and physically OLIMEXINO-328. 6.1 Eagle schematics Stand-alone search-able schematic in PDF format might be found at the web page of OLIMEXINO- 328. - Page 19 OLIMEX© 2017 OLIMEXINO-328 user's manual 5V_USB DVCC RXD_E C1739pF D0(RXD) Close TXD 1 TXD_E VCCIO FB/600 OHM/1206(321611C-601) RXD 5 C1839pF D1(TXD) DVCC RTS# 3 Close Q16.000MHz/HC-49S/20pF/20ppm/PTH VBUS CON1 CTS# 11 USBDM DTR# 2 RESET USBDP 0R(NA) 3.3V DSR# 9 PCINT7/XTAL2/TOSC2/PB7...
-
Page 20: Physical Dimensions
OLIMEX© 2017 OLIMEXINO-328 user's manual 6.2 Physical dimensions Note that all dimensions are in inches. Page 20 of 24... -
Page 21: Chapter 7 - Revision History And Support
OLIMEX© 2017 OLIMEXINO-328 user's manual CHAPTER 7 – REVISION HISTORY AND SUPPORT 7. Introduction to the chapter In this chapter you will find the current and the previous version of the document you are reading. Also the web-page for your device is listed. Be sure to check it after a purchase for the latest available updates and examples. -
Page 22: Board Revision
AVR-ISP500 – assembled and tested AVR-ISP compatible programmer AVR-ISP-MK2 – assembled and tested AVR-ISP compatible programmer How to purchase Olimex products? You can order from our web-shop or from any of our distributors. The list of official Olimex distributors might be found at: https://www.olimex.com/Distributors/. Please check https://www.olimex.com/... -
Page 23: Faq
What might be causing the problem? A2: Very often people try to use the PDI or TPI interface of AVR-ISP-MK2 for the ICSP slot of OLIMEXINO-328. Please, use jumper wires to transform the 10-pin ICSP of the AVR-ISP-MK2 to 6-pin ICSP connector of the OLIMEXINO-328. -
Page 24: Product Support
All goods are checked before they are sent out. In the unlikely event that goods are faulty, they must be returned, to OLIMEX at the address listed on your order invoice. OLIMEX will not accept goods that have clearly been used more than the amount needed to evaluate their functionality.