Advertisement
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY PRECAUTIONS
•
If you are working with the sanding machine, wear
always ear protectors and dust mask.
•
The sanding machine is not suitable for wet sanding.
•
Check if the switch is not in position "ON", before
you connect the mains plug to the mains voltage.
•
Keep the mains lead always away from moving parts
of the tools.
•
Use safety glasses, especially when you sand above
your head.
•
Do not bring pressure to your machine, this will only
delay the sanding.
The dust that is produced while working can be
detrimental to health, inflammable or explosive.
Suitable safety measures are required. Always wear suitable
safety equipment, for example a dust mask, and use the
dust bag.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
•
Excessive sparking of the carbon brushes and
verticiliosis in the collector.
•
Interruption of the mains plug, mains lead or mains
lead damage.
•
Defect switch
•
Smoke or stench of scorched isolation
4
3. OPERATION
Always observe the safety instructions and
applicable regulations.
CHOICE OF THE SAND-PAPER
Coarse sand-paper (grain 50) removes in general the
bigger part of the material and fine sand-paper is used for
the finishing. If the surface is not even, then start with
rough sand-paper. Further you use middle coarse sand-
paper(grain 80) to remove the scratches left behind by
the coarse sand-paper and finally you take fine sand-
paper (grain 120) for the finishing.
REMOVING AND INSTALLING THE
SANDING BELT
Fig. C1 + C2
Before assembly the sanding belt always remove
the plug from the mains.
•
Put the machine on its side, with the drive belt cover
down wards.
•
Loosen the sanding belt fastener (4).
•
Remove the sanding belt from the machine
•
Put a new sanding belt on the machine, make sure
that the direction arrows on the sanding belt are
pointing in the same direction as the direction
indicator (5).
•
Fasten the sanding belt fastener again (4).
ALIGNING THE SANDING BELT
Fig. B
If the sanding belt doesn't run parallel with the outer
edge of the housing, the sanding belt must be aligned.
Move the sanding belt in the correct position with the
adjusting knob (12). By turning the adjusting knob
clockwise the sanding belt will move to the inside and
by turning anti-clockwise the sanding belt will move to
the outside.
SWITCHING ON AND OFF
Fig. B
•
To switch the machine on press the on/off switch
(7).
•
To switch the machine off release the on/off switch.
If continuous operation is required the blocking
switch (8) must be used:
•
Switch the machine on to press the on/off switch.
•
Press the blocking switch and release the on/off
switch.
•
To switch the machine off press the on/off switch
again and release the on/off switch.
MOUNTING DUSTBAG
Fig. B
A complete dust bag is enclosed. Put the wire-bracket
(inside the dust bag) into to the adapter of the dust bag
(when not mounted). The end of the bracket has to point
upwards. Use the dust bag to collect dust which is
released during sanding.
•
Put the dust bag on the dust collection opening
•
Empty the dust bag regularly in order to obtain an
4. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der
udføres vedligeholdelsesarbejder på mekanikken.
Maskinerne fra Ferm er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse. Ved at
rengøre maskinen regelmæssigt og behandle den
korrekt, bidrager De til en længere levetid for maskinen.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud,
helst efter hvert brug. Sørg for at ventilationshullerne er
fri for støv og snavs. Brug en blød klud, der er vædet i
sæbevand til at fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol, ammoniak,
osv. Den slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Kontakt Deres Ferm-forhandler, hvis der opstår fejl som
følge af slitage af en del.
Bagerst i denne brugsanvisning finder De en
reservedelstegning med de reservedele, der kan
bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet af
genbrugsmateriale. Genbrug derfor emballagen.
Når de udskifter Deres maskinen bør De tage den gamle
maskine med til Deres lokale Ferm-forhandler. Der vil
maskinen blive bearbejdet på miljøvenlig vis.
GARANTI
Læs det separat vedlagte garantikort for
garantibetingelserne.
ı
CE
KONFORMITETSERKLÆRING
Vi erklærer herved, udelukkende på eget ansvar, at dette
produkt opfylder følgende standarder eller
standardiserede dokumenter
EN60745-1, EN60745-2-4, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
i henhold til følgende direktiver:
98/37/EEC
73/23/EEC
89/336/EEC
01-07-2005
ZWOLLE NL
W. Kamphof
Quality department
Ferm
Ferm
( DK )
37
Advertisement
