Icom IC-F3262D Series Instructions

PANEL DESCRIPTION
[Rotary Selector]
[VOL]
Antenna
connector
LED indicator
[Emer]*
GPS receiver*
[Side1]*
Speaker
Multi-connector
[PTT]
Microphone
Function display
[Side2]*
[Side3]*
[P0]* 2 , [P1]*
[P2]* 2 , [P3]*
10-keypad
The illustration is of the 10-key type transceivers.
FUNCTION DISPLAY
q we rt y u i o
001 ch-01
!0
IC-F3262D
CLR MENU
!1
q SIGNAL STRENGTH ICON
Displays the relative receive signal strength.
w LOW POWER ICON
Displayed when low output power is selected.
PRIVATE
• When the battery charge decreases to a specified level, low
power is automatically selected.
ID 0000002
e SPEAKER/TELEPHONE ICON
➥ Displayed when the channel is in the 'audible' BIIS
CALL dPMR MENU CLR
(unmute) mode.
➥ Displayed when a matched signal is received.
➥ " " is displayed when connecting to a telephone line.
r SCRAMBLER ICON
Displayed when the Voice Scrambler function is ON.
t SCAN ICON
Displayed while scanning.
y MESSAGE ICON
➥ Displayed when a received message (Short Data
Message or Status Message) is stored in the stack
memory.
➥ Blinks when an unread message is in the stack
memory.
D About the LED indicator
• Lights red while transmitting.
• Lights green while receiving a signal, or when
the squelch is open.
• Blinks red when the battery is exhausted.
1
D About the Multi-connector
CAUTION: Attach the connector cover
when an optional accessory is not used.
2 ,
2
1
* A GPS receiver is bult-in, depending on the transceiver version.
2
* Dealer assignable
u BELL ICON
D isplayed when a matched signal is received, depending
on the presetting.
i GPS/COMPANDER ICON
➥ Displayed when the GPS receiver acquires the GPS
signal from a satellite and the GPS Indicator is set to
ON.
➥ " " is displayed when the Compander function is
activated and the GPS Indicator is set to OFF.
o BATTERY ICON
Displays the battery level.
Indication
Charging Exhausted
Battery level Full Mid
required
0001 blinks when the battery is over charged.
blinks when the battery is exhausted.
1234
• This icon may not be displayed, depending on the presetting.
!0 ALPHANUMERIC READOUT
CALL TXCE MON
➥ Displays the operating channel number, channel
name, Menu contents, DTMF code, and so on.
➥ Depending on the presetting, characters are displayed
in 1 line or 2 lines on the display.
• In this instruction manual, the display illustration is
described as having characters displayed in 2 lines.
!1 KEY ICONS
Display the assigned function of the [P0], [P1], [P2] and
[P3] front panel keys.
– 4 –
VHF dPMR HANDHELD TRANSCEIVERS
Iç-F3262D
UHF dPMR HANDHELD TRANSCEIVERS
Iç-F4262D
FOREWORD
This instruction sheet includes some functions which are
usable only when they are preset by your dealer. Ask your
dealer for details.
See the operating guide for details of the dPMR™ (digital
Private Mobile Radio) and the BIIS (Binary Interchange
of Information and Signaling) 1200 system operations.
Ask your dealer for details.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
• Force majeure, including, but not limited to, fires, earthquakes,
storms, floods, lightning, other natural disasters, disturbances,
riots, war, or radioactive contamination.
• The use of Icom transceivers with any equipment that is not
manufactured or approved by Icom.
Icom, Icom Inc. and Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain,
Russia, Australia, New Zealand, and/or other countries.
dPMR and the dPMR logo are trademarks of the dPMR MoU Association.
All other products or brands are registered trademarks or trademarks of their respective holders.
D Turning power ON
Before using the transceiver for the first time, the battery
pack must be fully charged for optimum life and
operation. See the back page of this sheet.
➥ Rotate [VOL] to turn ON the power.
Battery
D Receiving and Transmitting
Receiving:
q Select a channel.
➥ Rotate [Rotary selector].
➥ Push [CH Up] or [CH Down].
➥ Push one of the direct channel select keys,
[MR-CH 1] to [MR-CH 4].
w When receiving a call, rotate [VOL] to adjust the audio
output level to a comfortable listening level.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
INSTRUCTIONS
series
Thank you for choosing the IC-F3262DT/IC-F3262DS
vhf dpmr handheld transceivers
IC-F4262DS
uhf dpmr handheld transceivers
series
READ ALL INSTRUCTIONS carefully and
completely before using your transceiver.
SUPPLIED ACCESSORIES
Flexible antenna
(This illustration is
for the UHF type.)
BASIC OPERATION
NOTE:
• If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
• The battery type must be selected, according to the
attached battery type, when tuning the transceiver ON.
See the operating guide for details of entering the
password or selecting the battery type.
Transmitting:
CAUTION: Attach an antenna before transmitting.
Transmitting without an antenna may damage the
transceiver.
Wait until the channel is clear to avoid interference.
q While holding down [PTT], speak at a normal voice level.
w Release [PTT] to receive.
IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start
speaking.
2. Hold the microphone 5 to 10 cm from your mouth, then
speak at a normal voice level.
– 1 –
or IC-F4262DT/
.
Battery pack Belt clip
Connector cover
(with screw)
A-7213D-1EU-w Printed in Japan
© 2015–2016 Icom Inc.