Vendo V-max Safety Manual
  1. Manuals
  2. Brands
  3. Vendo Manuals
  4. Vending machines
  5. V-max
  6. Safety manual
Vendo V-max Safety Manual

Vendo V-max Safety Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SAFETY SECTION
S-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V-max and is the answer not in the manual?

Questions and answers

Related Manuals for Vendo V-max

Summary of Contents for Vendo V-max

  • Page 1 SAFETY SECTION...

  • Page 2: A Commitment To Safety

    Vendo has no control over the machine once it leaves the premises. It is the owner or lessor’s responsibility to maintain the vendor in a safe condition. See Section I of this manual for proper installation procedures and refer to the appropriate service manual for recommended maintenance procedures.

  • Page 3: Section I: Vendor Installation

    SECTION I: VENDOR INSTALLATION Vendors are large, bulky machines of significant size and weight. Improper handling can result in injury. When moving a vendor, carefully plan the route to be taken and the people and equipment required to accomplish the task safely. Remove all tape, shipping sealant, and Styrofoam from the vendor.
  • Page 4 TYPE 1 STEP 3 LARGE SLOT-LINE 2 STEP 1 NEUTRAL CONTACT (WHITE ) 0 - 5 VOLTS STEP 2 SMALL SLOT-LINE 1 LIVE CONTACT (BLACK) 110 VOLTS ROUND SOCKET EARTH CONTACT (GREEN) 0 VOLTS EARTH CONTACT SLOT TYPE 2 STEP 2 STEP 3 (GREEN AND YELLOW) 0 VOLTS...
  • Page 5 SECTION I: VENDOR INSTALLATION (CONTINUED) For Type 1 and Type 2 outlets, test for Grounding and Polarization as follows: With a test device (volt meter or test light), connect one probe to the receptacle’s neutral contact and the other to the live contact. The test device should show a reaction.
  • Page 6 SECTION I: VENDOR INSTALLATION (CONTINUED) Door Support (Figure 2) The door support is to ensure that the outer door closes squarely to the cabinet. Raising the door can also ensure proper alignment of the door latch. FIGURE 2 NOTE: Refer to the appropriate parts and service manual for detailed instructions, operating principles, and recommended maintenance intervals and procedures.

  • Page 7: Section Ii: Electrical Hazards

    SECTION II: ELECTRICAL HAZARDS GENERAL Vendo vending machines are provided with the appropriate power supply setting for your area. Some models are equipped with step-down transformers, as required. This enables the vending machine to operate on different main voltages. Refer to Section I. E. for information to determine the main power requirements.
  • Page 8 INDIVIDUALS CAN BE DANGEROUS. Power to lighting and refrigeration system is shut off automatically by the electronic controller when the outer door is opened. Applies to V-Max only. NOTE: For power-on servicing of the vendor’s lighting system, turn lighting power on by accessing the Lights test function of the electronic controller (see programming on inner door).

  • Page 9: Section Iii: Mechanical Hazards

    WARNING: THIS VENDING MACHINE INCLUDES MECHANICAL EQUIPMENT WHICH CAN BE HAZARDOUS IF IMPROPERLY HANDLED OR SERVICED. USE CAUTION AND CONSULT THE VENDO SAFETY MANUAL AND THE VENDO SERVICE MANUAL FOR ADDITIONAL SAFETY INFORMATION. WARNING WARNING RISK OF SHOCK RISK OF ENTRAPMENT...

  • Page 10: Section Iv: Refrigeration Hazards

    SECTION IV: REFRIGERATION HAZARDS GENERAL Refrigeration systems involve both electrical power and mechanical action. These systems may present any of the potential dangers shown in the sections on electrical and mechanical hazards contained in this manual. See Sections II and III for further information. Compressed Refrigerant Refrigeration systems involve the compression and evaporation of gases.

  • Page 11: Section Vi: Substitutions And Modifications

    If questions arise, contact the Technical Services Department of the Vendo office in your area. When servicing the vending machine, always reassemble all components to their original location and position. Maintain the correct routing for tubing, electrical wiring, etc.
  • Page 12 SECTION VI: SUBSTITUTIONS AND MODIFICATIONS (CONTINUED) WARNING: THIS APPLIANCE MUST BE EARTHED. IMPORTANT! The wires in the main leads are colored in accordance with the following code: 110v/120v 220v/240v Green Green and Yellow........ Earth White Blue ............Neutral Black Brown ............ Live S-12...

  • Page 13: Section Vii: Consumer Safety Warning

    (One such decal is supplied with the vending machine.) Vendo will supply sufficient decals to be placed on all machines, on request. If you have any questions, contact the Technical Services Department of the Vendo office in your area.
  • Page 14 PARTS, SALES, & SERVICE CENTERS OF VENDO/SANDEN COMPANY AREA ADDRESS PHONE NUMBERS United States, The Vendo Company Tel: (559) 439-1770 Canada 7209 N. Ingram Fax: (559) 439-2083 Fresno, CA 93650 U.S.A. Japan Sanden International Corporation Tel: (81) 3-3835-1321 31-7 Taito 1-Chome...

  • Page 15: Phone Numbers

    PARTS, SALES, & SERVICE CENTERS OF VENDO/SANDEN COMPANY FOR LATIN AMERICA AREA ADDRESS PHONE NUMBERS Mexico Vendo de Mexico Tel: (525) 515-9745 Camino Real de Toluca No. 154 Fax: (525) 277-0111 Col. Bellavista 01140 Mexico D.F. Mexico Central America The Vendo Company Tel: (559) 439-1770 7209 N.
  • Page 16 NOTES S-16...

Table of Contents